[Çözüldü] Ubuntu 12.04 Ağ bağlantısı sorunu.

[Gam Kenarı]

Daha önce aşağıda linkini eklediğim başlıkta olduğu gibi Ubuntu 14.04 kullanıyordum; fakat sürekli donma sorunu yaşıyordum. Bir ara donma sorunu ortadan kalkmıştı. İlerleyen zamanda bu sorun tekrar başlayınca, @shadow nickli arkadaşın tavsiyesine uyarak Ubuntu 14.04'ün 64 bit olanını kurdum ama donma sorununu onda da yaşayınca 12.04'de geçiş yaptım.
https://forum.ubuntu-tr.net/index.php?topic=43161.0


Ubuntu 12.04 sürümünde yaşadığım sorun

12.04 sürümünü ilk kurduğumda ağ bağlantısı sorunu yaşadım. Bu sorunu düzeltemeyince tekrar kurulum yaptım, aynı sorunu yine devam etti. Ağ bağlantısını aşağıdaki komutu terminalden yürüterek çalıştırabiliyorum.

Kod Seç Genişlet

sudo pkill -9 NetworkManager

Bilgisayarı her açtığımda bu komutu girmem gerekiyor. Bu sorunu nasıl düzeltebilirim?

cat /etc/lsb-release

Kod Seç Genişlet

DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=12.04
DISTRIB_CODENAME=precise
DISTRIB_DESCRIPTION="Ubuntu 12.04.4 LTS"


uname -a

Kod Seç Genişlet

Linux okyanus 3.11.0-20-generic #35~precise1-Ubuntu SMP Fri May 2 21:35:48 UTC 2014 i686 athlon i386 GNU/Linux


lspci

Kod Seç Genişlet

00:00.0 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a1)
00:01.0 ISA bridge: NVIDIA Corporation MCP61 LPC Bridge (rev a2)
00:01.1 SMBus: NVIDIA Corporation MCP61 SMBus (rev a2)
00:01.2 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a2)
00:02.0 USB controller: NVIDIA Corporation MCP61 USB 1.1 Controller (rev a2)
00:02.1 USB controller: NVIDIA Corporation MCP61 USB 2.0 Controller (rev a2)
00:04.0 PCI bridge: NVIDIA Corporation MCP61 PCI bridge (rev a1)
00:05.0 Audio device: NVIDIA Corporation MCP61 High Definition Audio (rev a2)
00:06.0 IDE interface: NVIDIA Corporation MCP61 IDE (rev a2)
00:07.0 Bridge: NVIDIA Corporation MCP61 Ethernet (rev a2)
00:08.0 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2)
00:09.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2)
00:0b.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2)
00:0c.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:08.0 Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)
02:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9400 GT] (rev a1)


lsusb

Kod Seç Genişlet

Bus 001 Device 002: ID 0781:5567 SanDisk Corp. Cruzer Blade
Bus 002 Device 002: ID 046d:c05a Logitech, Inc. Optical Mouse M90
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


rfkill list
(Herhangi bir çıktı vermedi)

sudo lshw -C network

Kod Seç Genişlet

  *-network               
       açıklama: Eternet interface
       ürün: IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY
       üretici: Sundance Technology Inc / IC Plus Corp
       physical id: 8
       bus info: pci@0000:01:08.0
       mantıksal ad: eth0
       sürüm: 31
       serial: f8:1a:67:00:c5:0d
       boyut: 100Mbit/s
       kapasite: 100Mbit/s
       genişlik: 32 bits
       saat: 33MHz
       kapasiteler: pm bus_master cap_list rom eternet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       yapılandırma: autonegotiation=on broadcast=yes driver=sundance driverversion=1.2 duplex=full ip=192.168.2.221 latency=64 link=yes maxlatency=10 mingnt=10 multicast=yes port=MII speed=100Mbit/s
       kaynaklar: irq:16 ioport:cc00(boyut=128) bellek:fdeff000-fdeff1ff bellek:fdf00000-fdf0ffff


ifconfig

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr f8:1a:67:00:c5:0d 
          inet addr:192.168.2.221  Bcast:192.168.2.255  Mask:255.255.255.0
          inet6 addr: fe80::fa1a:67ff:fe00:c50d/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:54906 errors:0 dropped:0 overruns:0 frame:0
          TX packets:37952 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:66193058 (66.1 MB)  TX bytes:4674824 (4.6 MB)

eth1      Link encap:Ethernet  HWaddr 00:e0:4d:45:5b:d5 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Sunucu
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:836 errors:0 dropped:0 overruns:0 frame:0
          TX packets:836 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:84419 (84.4 KB)  TX bytes:84419 (84.4 KB)


iwconfig

Kod Seç Genişlet

lo        no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.


iwlist scanning

Kod Seç Genişlet

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

eth1      Interface doesn't support scanning.


lsmod

Kod Seç Genişlet

Module                  Size  Used by
nls_iso8859_1          12617  1
bnep                   19210  2
rfcomm                 59026  0
bluetooth             341971  10 bnep,rfcomm
nvidia              10304659  40
binfmt_misc            17268  1
snd_hda_codec_realtek    50931  1
snd_hda_intel          43326  3
snd_hda_codec         169608  2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep              13276  1 snd_hda_codec
snd_pcm                94597  2 snd_hda_intel,snd_hda_codec
snd_seq_midi           13132  0
snd_rawmidi            25157  1 snd_seq_midi
snd_seq_midi_event     14475  1 snd_seq_midi
snd_seq                55716  2 snd_seq_midi,snd_seq_midi_event
snd_timer              28930  2 snd_pcm,snd_seq
snd_seq_device         14137  3 snd_seq_midi,snd_rawmidi,snd_seq
snd                    61270  16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq_midi,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
serio_raw              13189  0
soundcore              12600  1 snd
snd_page_alloc         18398  2 snd_hda_intel,snd_pcm
k8temp                 12912  0
ppdev                  17423  0
parport_pc             32114  1
mac_hid                13077  0
i2c_nforce2            13104  0
lp                     13359  0
parport                40930  3 ppdev,parport_pc,lp
pata_acpi              12886  0
hid_generic            12492  0
usbhid                 47620  0
hid                    87771  2 hid_generic,usbhid
usb_storage            48631  1
sundance               26613  0
mii                    13693  1 sundance
floppy                 60183  0
sata_nv                23371  2
pata_amd               13761  0
forcedeth              62780  0


dmesg

Kod Seç Genişlet

[    0.194588] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[    0.194689] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[    0.194791] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[    0.194892] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[    0.194992] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[    0.195093] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[    0.195194] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[    0.195295] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[    0.195396] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[    0.195497] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[    0.196149] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.196159] ACPI: \_SB_.PCI0: notify handler is installed
[    0.196234] Found 1 acpi root devices
[    0.196374] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.196374] vgaarb: loaded
[    0.196374] vgaarb: bridge control possible 0000:02:00.0
[    0.196374] SCSI subsystem initialized
[    0.196374] ACPI: bus type ATA registered
[    0.196374] libata version 3.00 loaded.
[    0.196374] ACPI: bus type USB registered
[    0.196374] usbcore: registered new interface driver usbfs
[    0.196374] usbcore: registered new interface driver hub
[    0.196374] usbcore: registered new device driver usb
[    0.196374] PCI: Using ACPI for IRQ routing
[    0.197459] PCI: pci_cache_line_size set to 64 bytes
[    0.197500] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
[    0.197504] e820: reserve RAM buffer [mem 0x7fef0000-0x7fffffff]
[    0.197631] NetLabel: Initializing
[    0.197632] NetLabel:  domain hash size = 128
[    0.197634] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.197646] NetLabel:  unlabeled traffic allowed by default
[    0.197664] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.197664] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[    0.197664] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    0.200031] Switched to clocksource hpet
[    0.207828] AppArmor: AppArmor Filesystem Enabled
[    0.207871] pnp: PnP ACPI init
[    0.207890] ACPI: bus type PNP registered
[    0.208165] system 00:00: [io  0x1000-0x107f] has been reserved
[    0.208168] system 00:00: [io  0x1080-0x10ff] has been reserved
[    0.208172] system 00:00: [io  0x1400-0x147f] has been reserved
[    0.208175] system 00:00: [io  0x1480-0x14ff] has been reserved
[    0.208178] system 00:00: [io  0x1800-0x187f] has been reserved
[    0.208181] system 00:00: [io  0x1880-0x18ff] has been reserved
[    0.208184] system 00:00: [io  0x2000-0x207f] has been reserved
[    0.208188] system 00:00: [io  0x2080-0x20ff] has been reserved
[    0.208192] system 00:00: [mem 0xfefe0000-0xfefe01ff] has been reserved
[    0.208195] system 00:00: [mem 0xfefe1000-0xfefe10ff] has been reserved
[    0.208201] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.208957] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.208960] system 00:01: [io  0x0800-0x087f] has been reserved
[    0.208963] system 00:01: [io  0x0290-0x029f] has been reserved
[    0.208967] system 00:01: [io  0x0290-0x0297] has been reserved
[    0.208970] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.208984] pnp 00:02: [dma 4]
[    0.209016] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.209108] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.209175] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.209213] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.209260] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.209443] pnp 00:07: [dma 2]
[    0.209490] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.209785] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.210089] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.210250] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.210325] system 00:0b: [mem 0xf0000000-0xf3ffffff] has been reserved
[    0.210329] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.210446] system 00:0c: [mem 0x000f0000-0x000fffff] could not be reserved
[    0.210450] system 00:0c: [mem 0xfeff0000-0xfeff00ff] has been reserved
[    0.210453] system 00:0c: [mem 0x7fef0000-0x7fefffff] could not be reserved
[    0.210456] system 00:0c: [mem 0xffff0000-0xffffffff] has been reserved
[    0.210460] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.210463] system 00:0c: [mem 0x00100000-0x7feeffff] could not be reserved
[    0.210466] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.210470] system 00:0c: [mem 0xfee00000-0xfeefffff] has been reserved
[    0.210473] system 00:0c: [mem 0xfefff000-0xfeffffff] has been reserved
[    0.210476] system 00:0c: [mem 0xfff80000-0xfff80fff] has been reserved
[    0.210480] system 00:0c: [mem 0xfff90000-0xfffbffff] has been reserved
[    0.210483] system 00:0c: [mem 0xfffed000-0xfffeffff] has been reserved
[    0.210486] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.210497] pnp: PnP ACPI: found 13 devices
[    0.210498] ACPI: bus type PNP unregistered
[    0.210501] PnPBIOS: Disabled by ACPI PNP
[    0.247856] pci 0000:01:08.0: BAR 6: assigned [mem 0xfdf00000-0xfdf0ffff pref]
[    0.247861] pci 0000:00:04.0: PCI bridge to [bus 01]
[    0.247864] pci 0000:00:04.0:   bridge window [io  0xc000-0xcfff]
[    0.247869] pci 0000:00:04.0:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.247872] pci 0000:00:04.0:   bridge window [mem 0xfdf00000-0xfdffffff pref]
[    0.247878] pci 0000:02:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref]
[    0.247881] pci 0000:00:09.0: PCI bridge to [bus 02]
[    0.247884] pci 0000:00:09.0:   bridge window [io  0xb000-0xbfff]
[    0.247888] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff]
[    0.247892] pci 0000:00:09.0:   bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[    0.247896] pci 0000:00:0b.0: PCI bridge to [bus 03]
[    0.247899] pci 0000:00:0b.0:   bridge window [io  0xa000-0xafff]
[    0.247902] pci 0000:00:0b.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.247906] pci 0000:00:0b.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.247910] pci 0000:00:0c.0: PCI bridge to [bus 04]
[    0.247913] pci 0000:00:0c.0:   bridge window [io  0x9000-0x9fff]
[    0.247917] pci 0000:00:0c.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.247920] pci 0000:00:0c.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.247930] pci 0000:00:04.0: setting latency timer to 64
[    0.247938] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.247941] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    0.247944] pci_bus 0000:00: resource 6 [mem 0x80000000-0xf3ffffff]
[    0.247947] pci_bus 0000:00: resource 7 [mem 0xf4000000-0xfcffffffff]
[    0.247951] pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
[    0.247954] pci_bus 0000:01: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.247957] pci_bus 0000:01: resource 2 [mem 0xfdf00000-0xfdffffff pref]
[    0.247960] pci_bus 0000:01: resource 4 [io  0x0000-0xffff]
[    0.247963] pci_bus 0000:01: resource 5 [mem 0x000a0000-0x000bffff]
[    0.247966] pci_bus 0000:01: resource 6 [mem 0x80000000-0xf3ffffff]
[    0.247969] pci_bus 0000:01: resource 7 [mem 0xf4000000-0xfcffffffff]
[    0.247972] pci_bus 0000:02: resource 0 [io  0xb000-0xbfff]
[    0.247975] pci_bus 0000:02: resource 1 [mem 0xf8000000-0xfbffffff]
[    0.247978] pci_bus 0000:02: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[    0.247981] pci_bus 0000:03: resource 0 [io  0xa000-0xafff]
[    0.247984] pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfddfffff]
[    0.247987] pci_bus 0000:03: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.247991] pci_bus 0000:04: resource 0 [io  0x9000-0x9fff]
[    0.247994] pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
[    0.247997] pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.248050] NET: Registered protocol family 2
[    0.248221] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.248261] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.248302] TCP: Hash tables configured (established 8192 bind 8192)
[    0.248342] TCP: reno registered
[    0.248345] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.248356] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.248423] NET: Registered protocol family 1
[    0.248748] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[    0.249070] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[    0.249204] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249254] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249314] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249372] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249435] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249502] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249574] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.249594] pci 0000:02:00.0: Boot video device
[    0.249597] PCI: CLS 64 bytes, default 64
[    0.249655] Trying to unpack rootfs image as initramfs...
[    0.643925] Freeing initrd memory: 16716K (f5f4a000 - f6f9d000)
[    0.644126] Scanning for low memory corruption every 60 seconds
[    0.644403] Initialise module verification
[    0.644460] audit: initializing netlink socket (disabled)
[    0.644476] type=2000 audit(1400931082.644:1): initialized
[    0.674288] bounce pool size: 64 pages
[    0.674300] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.676069] zbud: loaded
[    0.676144] VFS: Disk quotas dquot_6.5.2
[    0.676202] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.676858] fuse init (API version 7.22)
[    0.676967] msgmni has been set to 1716
[    0.677639] Key type asymmetric registered
[    0.677642] Asymmetric key parser 'x509' registered
[    0.677690] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.677737] io scheduler noop registered
[    0.677740] io scheduler deadline registered (default)
[    0.677772] io scheduler cfq registered
[    0.677924] pcieport 0000:00:09.0: irq 40 for MSI/MSI-X
[    0.677977] pcieport 0000:00:0b.0: irq 41 for MSI/MSI-X
[    0.678020] pcieport 0000:00:0c.0: irq 42 for MSI/MSI-X
[    0.678086] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.678111] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.678299] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.678305] ACPI: Power Button [PWRB]
[    0.678350] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[    0.678354] ACPI: Sleep Button [SLPB]
[    0.678416] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.678419] ACPI: Power Button [PWRF]
[    0.678478] ACPI: Fan [FAN] (on)
[    0.678984] thermal LNXTHERM:00: registered as thermal_zone0
[    0.678987] ACPI: Thermal Zone [THRM] (33 C)
[    0.679022] GHES: HEST is not enabled!
[    0.679099] isapnp: Scanning for PnP cards...
[    0.679120] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.699521] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.701033] Linux agpgart interface v0.103
[    0.702691] brd: module loaded
[    0.703463] loop: module loaded
[    0.703553] megasas: 06.600.18.00-rc1 Wed. May. 15 17:00:00 PDT 2013
[    0.704060] libphy: Fixed MDIO Bus: probed
[    0.704197] tun: Universal TUN/TAP device driver, 1.6
[    0.704198] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.704243] PPP generic driver version 2.4.2
[    0.704288] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.704290] ehci-pci: EHCI PCI platform driver
[    0.704449] ehci-pci 0000:00:02.1: setting latency timer to 64
[    0.704461] ehci-pci 0000:00:02.1: EHCI Host Controller
[    0.704468] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    0.704478] ehci-pci 0000:00:02.1: debug port 1
[    0.704508] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    0.704538] ehci-pci 0000:00:02.1: irq 22, io mem 0xfe02e000
[    0.716019] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    0.716062] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.716064] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.716067] usb usb1: Product: EHCI Host Controller
[    0.716070] usb usb1: Manufacturer: Linux 3.11.0-20-generic ehci_hcd
[    0.716072] usb usb1: SerialNumber: 0000:00:02.1
[    0.716194] hub 1-0:1.0: USB hub found
[    0.716200] hub 1-0:1.0: 8 ports detected
[    0.716379] ehci-platform: EHCI generic platform driver
[    0.716390] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.716392] ohci-pci: OHCI PCI platform driver
[    0.716490] ohci-pci 0000:00:02.0: setting latency timer to 64
[    0.716493] ohci-pci 0000:00:02.0: OHCI PCI host controller
[    0.716498] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 2
[    0.716529] ohci-pci 0000:00:02.0: irq 23, io mem 0xfe02f000
[    0.774020] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.774023] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.774025] usb usb2: Product: OHCI PCI host controller
[    0.774028] usb usb2: Manufacturer: Linux 3.11.0-20-generic ohci_hcd
[    0.774030] usb usb2: SerialNumber: 0000:00:02.0
[    0.774123] hub 2-0:1.0: USB hub found
[    0.774129] hub 2-0:1.0: 8 ports detected
[    0.774277] ohci-platform: OHCI generic platform driver
[    0.774287] uhci_hcd: USB Universal Host Controller Interface driver
[    0.774373] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.774375] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.774541] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.774640] mousedev: PS/2 mouse device common for all mice
[    0.774791] rtc_cmos 00:04: RTC can wake from S4
[    0.774945] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    0.774985] rtc_cmos 00:04: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    0.775065] device-mapper: uevent: version 1.0.3
[    0.775130] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[    0.775215] platform eisa.0: Probing EISA bus 0
[    0.775221] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    0.775224] platform eisa.0: Cannot allocate resource for EISA slot 1
[    0.775227] platform eisa.0: Cannot allocate resource for EISA slot 2
[    0.775230] platform eisa.0: Cannot allocate resource for EISA slot 3
[    0.775233] platform eisa.0: Cannot allocate resource for EISA slot 4
[    0.775236] platform eisa.0: Cannot allocate resource for EISA slot 5
[    0.775239] platform eisa.0: Cannot allocate resource for EISA slot 6
[    0.775242] platform eisa.0: Cannot allocate resource for EISA slot 7
[    0.775245] platform eisa.0: Cannot allocate resource for EISA slot 8
[    0.775247] platform eisa.0: EISA: Detected 0 cards
[    0.775257] cpufreq-nforce2: No nForce2 chipset.
[    0.775260] cpuidle: using governor ladder
[    0.775261] cpuidle: using governor menu
[    0.775273] ledtrig-cpu: registered to indicate activity on CPUs
[    0.775377] TCP: cubic registered
[    0.775496] NET: Registered protocol family 10
[    0.775696] NET: Registered protocol family 17
[    0.775714] Key type dns_resolver registered
[    0.775883] Using IPI No-Shortcut mode
[    0.775966] PM: Hibernation image not present or could not be loaded.
[    0.775970] Loading module verification certificates
[    0.780268] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: d668522bd3c23a786c2f05ef3e9bd58a57def500'
[    0.780283] registered taskstats version 1
[    0.797143] Key type trusted registered
[    0.797793] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    0.813102] Key type encrypted registered
[    0.821154] AppArmor: AppArmor sha1 policy hashing enabled
[    0.821410]   Magic number: 14:440:530
[    0.821437] tty ttyS10: hash matches
[    0.821525] rtc_cmos 00:04: setting system clock to 2014-05-24 11:31:23 UTC (1400931083)
[    0.821667] powernow-k8: fid 0xe (2200 MHz), vid 0xc
[    0.821669] powernow-k8: fid 0xc (2000 MHz), vid 0xe
[    0.821671] powernow-k8: fid 0xa (1800 MHz), vid 0x10
[    0.821673] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[    0.821704] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ (2 cpu cores) (version 2.20.00)
[    0.821709] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.821710] EDD information not available.
[    1.028020] usb 1-3: new high-speed USB device number 2 using ehci-pci
[    1.032965] isapnp: No Plug & Play device found
[    1.033506] Freeing unused kernel memory: 900K (c1a80000 - c1b61000)
[    1.033564] Write protecting the kernel text: 6684k
[    1.033671] Write protecting the kernel read-only data: 3448k
[    1.033672] NX-protecting the kernel data: 5604k
[    1.053826] udevd[95]: starting version 175
[    1.164821] usb 1-3: New USB device found, idVendor=0781, idProduct=5567
[    1.164828] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.164831] usb 1-3: Product: Cruzer Blade
[    1.164834] usb 1-3: Manufacturer: SanDisk
[    1.164836] usb 1-3: SerialNumber: 2004310930081561BBD3
[    1.169523] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[    1.169833] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
[    1.169857] forcedeth 0000:00:07.0: setting latency timer to 64
[    1.225483] Floppy drive(s): fd0 is 1.44M
[    1.239376] sundance.c:v1.2 11-Sep-2006 Written by Donald Becker
[    1.239633] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[    1.239658] sundance 0000:01:08.0: setting latency timer to 64
[    1.240196] eth0: IC Plus Corporation IP100A FAST Ethernet Adapter at 0001cc00, f8:1a:67:00:c5:0d, IRQ 16.
[    1.240631] eth0: MII PHY found at address 0, status 0x7849 advertising 01e1.
[    1.275540] FDC 0 is a post-1991 82077
[    1.428022] hub 1-0:1.0: over-current condition on port 7
[    1.636027] hub 1-0:1.0: over-current condition on port 8
[    1.692735] forcedeth 0000:00:07.0: ifname eth1, PHY OUI 0x732 @ 1, addr 00:e0:4d:45:5b:d5
[    1.692741] forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
[    1.692783] pata_amd 0000:00:06.0: version 0.4.1
[    1.692838] pata_amd 0000:00:06.0: setting latency timer to 64
[    1.693213] scsi0 : pata_amd
[    1.693498] scsi1 : pata_amd
[    1.693711] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    1.693713] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    1.693747] sata_nv 0000:00:08.0: version 3.5
[    1.694034] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
[    1.694100] sata_nv 0000:00:08.0: setting latency timer to 64
[    1.694486] scsi2 : sata_nv
[    1.694578] scsi3 : sata_nv
[    1.694650] ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 20
[    1.694653] ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 20
[    1.844033] hub 1-0:1.0: over-current condition on port 1
[    1.858994] ata2: port disabled--ignoring
[    2.052018] hub 1-0:1.0: over-current condition on port 2
[    2.160035] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.168226] ata3.00: ATAPI: TSSTcorp CDDVDW SH-S223C, SB01, max UDMA/100
[    2.184237] ata3.00: configured for UDMA/100
[    2.187935] scsi 2:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S223C  SB01 PQ: 0 ANSI: 5
[    2.190857] usb-storage 1-3:1.0: USB Mass Storage device detected
[    2.191052] scsi4 : usb-storage 1-3:1.0
[    2.191147] usbcore: registered new interface driver usb-storage
[    2.191325] sr0: scsi3-mmc drive: 52x/52x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.191328] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.191456] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.191615] sr 2:0:0:0: Attached scsi generic sg0 type 5
[    2.356021] usb 2-4: new low-speed USB device number 2 using ohci-pci
[    2.568087] usb 2-4: New USB device found, idVendor=046d, idProduct=c05a
[    2.568091] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.568094] usb 2-4: Product: USB Optical Mouse
[    2.568097] usb 2-4: Manufacturer: Logitech
[    2.582114] hidraw: raw HID events driver (C) Jiri Kosina
[    2.595170] usbcore: registered new interface driver usbhid
[    2.595174] usbhid: USB HID core driver
[    2.602314] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input4
[    2.602483] hid-generic 0003:046D:C05A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:02.0-4/input0
[    2.656052] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.664245] ata4.00: HPA detected: current 976771055, native 976773168
[    2.664252] ata4.00: ATA-7: SAMSUNG HD502HI, 1AG01118, max UDMA7
[    2.664254] ata4.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.672234] ata4.00: configured for UDMA/133
[    2.672407] scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG HD502HI  1AG0 PQ: 0 ANSI: 5
[    2.672638] sd 3:0:0:0: [sda] 976771055 512-byte logical blocks: (500 GB/465 GiB)
[    2.672653] sd 3:0:0:0: Attached scsi generic sg1 type 0
[    2.672723] sd 3:0:0:0: [sda] Write Protect is off
[    2.672727] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.672766] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.741402]  sda: sda1 sda2 < sda5 sda6 sda7 >
[    2.741938] sd 3:0:0:0: [sda] Attached SCSI disk
[    3.189023] scsi 4:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.00 PQ: 0 ANSI: 2
[    3.189397] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    3.190200] sd 4:0:0:0: [sdb] 15625216 512-byte logical blocks: (8.00 GB/7.45 GiB)
[    3.191843] sd 4:0:0:0: [sdb] Write Protect is off
[    3.191850] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[    3.192834] sd 4:0:0:0: [sdb] No Caching mode page found
[    3.192839] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.196943] sd 4:0:0:0: [sdb] No Caching mode page found
[    3.196949] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.200890]  sdb: sdb1
[    3.204674] EXT4-fs (sda7): INFO: recovery required on readonly filesystem
[    3.204683] EXT4-fs (sda7): write access will be enabled during recovery
[    3.204842] sd 4:0:0:0: [sdb] No Caching mode page found
[    3.204848] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.204853] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[    3.593573] EXT4-fs (sda7): orphan cleanup on readonly fs
[    3.752249] EXT4-fs (sda7): 9 orphan inodes deleted
[    3.752251] EXT4-fs (sda7): recovery complete
[    4.089765] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[    5.037456] init: ureadahead main process (359) terminated with status 5
[    5.854048] Adding 30717948k swap on /dev/sda6.  Priority:-1 extents:1 across:30717948k FS
[    6.644818] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.644828] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[    6.877815] udevd[433]: starting version 175
[    7.810080] lp: driver loaded but no devices found
[    7.978822] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[    8.096679] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
[    8.096750] i2c i2c-1: nForce2 SMBus adapter at 0x1c40
[    8.212671] parport_pc 00:09: reported by Plug and Play ACPI
[    8.212722] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[    8.292546] lp0: using parport0 (interrupt-driven).
[    8.444233] ppdev: user-space parallel port driver
[    8.450356] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[    9.845032] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[    9.845042] hda_intel: Disabling MSI
[    9.845074] snd_hda_intel 0000:00:05.0: setting latency timer to 64
[    9.845078] hda-intel 0000:00:05.0: Disabling 64bit DMA
[    9.849453] hda-intel 0000:00:05.0: Enable delay in RIRB handling
[   10.568023] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   10.568029]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   10.568031]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   10.568033]    mono: mono_out=0x0
[   10.568034]    dig-out=0x1e/0x0
[   10.568036]    inputs:
[   10.568038]      Front Mic=0x19
[   10.568040]      Rear Mic=0x18
[   10.568042]      Line=0x1a
[   10.568045] realtek: Enabling init ASM_ID=0xc601 CODEC_ID=10ec0862
[   11.369434] type=1400 audit(1400931094.045:2): apparmor="STATUS" operation="profile_load" parent=806 profile="unconfined" name="/sbin/dhclient" pid=820 comm="apparmor_parser"
[   11.369445] type=1400 audit(1400931094.045:3): apparmor="STATUS" operation="profile_load" parent=806 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=820 comm="apparmor_parser"
[   11.369452] type=1400 audit(1400931094.045:4): apparmor="STATUS" operation="profile_load" parent=806 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=820 comm="apparmor_parser"
[   11.369474] type=1400 audit(1400931094.045:5): apparmor="STATUS" operation="profile_replace" parent=809 profile="unconfined" name="/sbin/dhclient" pid=822 comm="apparmor_parser"
[   11.369487] type=1400 audit(1400931094.045:6): apparmor="STATUS" operation="profile_replace" parent=809 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=822 comm="apparmor_parser"
[   11.369493] type=1400 audit(1400931094.045:7): apparmor="STATUS" operation="profile_replace" parent=809 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=822 comm="apparmor_parser"
[   11.370146] type=1400 audit(1400931094.045:8): apparmor="STATUS" operation="profile_replace" parent=806 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=820 comm="apparmor_parser"
[   11.370155] type=1400 audit(1400931094.045:9): apparmor="STATUS" operation="profile_replace" parent=806 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=820 comm="apparmor_parser"
[   11.370186] type=1400 audit(1400931094.045:10): apparmor="STATUS" operation="profile_replace" parent=809 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=822 comm="apparmor_parser"
[   11.370193] type=1400 audit(1400931094.045:11): apparmor="STATUS" operation="profile_replace" parent=809 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=822 comm="apparmor_parser"
[   11.672206] input: HDA NVidia Front Headphone as /devices/pci0000:00/0000:00:05.0/sound/card0/input5
[   11.672312] input: HDA NVidia Line Out as /devices/pci0000:00/0000:00:05.0/sound/card0/input6
[   11.672393] input: HDA NVidia Line as /devices/pci0000:00/0000:00:05.0/sound/card0/input7
[   11.672476] input: HDA NVidia Rear Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input8
[   11.672554] input: HDA NVidia Front Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input9
[   11.742482] nvidia: module license 'NVIDIA' taints kernel.
[   11.742488] Disabling lock debugging due to kernel taint
[   11.758078] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[   11.766024] ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16
[   11.766042] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   11.766328] NVRM: loading NVIDIA UNIX x86 Kernel Module  304.116  Mon Oct 28 20:43:01 PDT 2013
[   12.063599] init: failsafe main process (903) killed by TERM signal
[   15.069808] Bluetooth: Core ver 2.16
[   15.069847] NET: Registered protocol family 31
[   15.069849] Bluetooth: HCI device and connection manager initialized
[   15.070080] Bluetooth: HCI socket layer initialized
[   15.070084] Bluetooth: L2CAP socket layer initialized
[   15.070092] Bluetooth: SCO socket layer initialized
[   15.350952] Bluetooth: RFCOMM TTY layer initialized
[   15.350969] Bluetooth: RFCOMM socket layer initialized
[   15.350971] Bluetooth: RFCOMM ver 1.11
[   15.360559] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.360565] Bluetooth: BNEP filters: protocol multicast
[   15.360576] Bluetooth: BNEP socket layer initialized
[   18.071034] init: udev-fallback-graphics main process (1226) terminated with status 1
[   19.318247] eth0: Link up
[   19.318490] eth0: Link changed: 100Mbps, full duplex
[   19.322620] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X
[   19.322657] forcedeth 0000:00:07.0 eth1: MSI enabled
[   19.322872] forcedeth 0000:00:07.0 eth1: no link during initialization
[   19.323288] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   19.323808] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   43.517826] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   58.916440] audit_printk_skb: 189 callbacks suppressed
[   58.916447] type=1400 audit(1400931141.593:75): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/mission-control-5" name="/usr/share/gvfs/remote-volume-monitors/" pid=2169 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  105.828130] init: network-manager main process (1155) killed by KILL signal
[  105.828169] init: network-manager main process ended, respawning
[ 5253.137417] Program lshw tried to access /dev/mem between ff000->101000.



dmesg | tail

Kod Seç Genişlet

[   19.322657] forcedeth 0000:00:07.0 eth1: MSI enabled
[   19.322872] forcedeth 0000:00:07.0 eth1: no link during initialization
[   19.323288] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   19.323808] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   43.517826] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   58.916440] audit_printk_skb: 189 callbacks suppressed
[   58.916447] type=1400 audit(1400931141.593:75): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/mission-control-5" name="/usr/share/gvfs/remote-volume-monitors/" pid=2169 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  105.828130] init: network-manager main process (1155) killed by KILL signal
[  105.828169] init: network-manager main process ended, respawning
[ 5253.137417] Program lshw tried to access /dev/mem between ff000->101000.


[heartsmagic]

Sorun kablolu bağlantıda sanrım? İlk açılışta mı oluyor bu sorun?
Ayrıca ikinci bir ağ kartı görünüyor, doğru mudur?

[Gam Kenarı]

@heartsmagic
Evet sorun kablolu bağlantıda. Bilgisayarı ilk açtığımda bu sorunla karşılaşıyorum. Aşağıdaki komutu terminalden yürüttükten sonra ağ bağlantısı kurulabiliyor.

Kod Seç Genişlet

sudo pkill -9 NetworkManager

Fazla anlamadığım için, ikinci bir ağ kartı hakkında bir bilgim yok.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 24 Mayıs 2014 - 18:13:51


Görüntüde olduğu gibi  "Kablolu Ağ (NVIDIA MCP61 Ethernet) bağlantı kesildi" diye yazıyor.  Fakat şu an internete girebiliyorum.

[heartsmagic]

Peki, ilk açtığın anda bağlantı olmadığında:

Kod Seç Genişlet

ifconfig

ne döndürüyor?

[Gam Kenarı]

Şöyle bir çıktı verdi:

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr f8:1a:67:00:c5:0d 
          inet6 addr: fe80::fa1a:67ff:fe00:c50d/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:4055 (4.0 KB)

eth1      Link encap:Ethernet  HWaddr 00:e0:4d:45:5b:d5 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Sunucu
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


[heartsmagic]

Peki ağ yöneticisinde "Ağ Yönetimini Etkinleştir" seçeneği ile ağı kapatıp açınca sorun çözülüyor mu? 
Senin uyguladığın çözüm ağ yöneticisini sonlandırmak.

[Gam Kenarı]

Peki ağ yöneticisinde "Ağ Yönetimini Etkinleştir" seçeneği ile ağı kapatıp açınca sorun çözülüyor mu?
Senin uyguladığın çözüm ağ yöneticisini sonlandırmak.

Bilgisayarı resetleyip söylediklerinizi denedim ama sorun çözülmüyor.

[heartsmagic]

İlginç bir durum var ortada, şu eth1 kafamı karıştırıyor.

Kod Seç Genişlet

dmesg | grep eth
nm-tool
lspci -nnk | grep -iA2 net

çıktılarını geçer misin sistem açılır açılmaz.

[Gam Kenarı]

Sistem açılır açılmaz uyguladım.

dmesg | grep eth

Kod Seç Genişlet

[    1.141697] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[    1.142021] forcedeth 0000:00:07.0: setting latency timer to 64
[    1.196249] eth0: IC Plus Corporation IP100A FAST Ethernet Adapter at 0001cc00, f8:1a:67:00:c5:0d, IRQ 16.
[    1.196679] eth0: MII PHY found at address 0, status 0x7849 advertising 01e1.
[    1.664732] forcedeth 0000:00:07.0: ifname eth1, PHY OUI 0x732 @ 1, addr 00:e0:4d:45:5b:d5
[    1.664738] forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
[    5.977298] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.977308] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   18.197877] eth0: Link up
[   18.198120] eth0: Link changed: 100Mbps, full duplex
[   18.201723] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X
[   18.201761] forcedeth 0000:00:07.0 eth1: MSI enabled
[   18.201976] forcedeth 0000:00:07.0 eth1: no link during initialization
[   18.202389] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   18.202917] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready


nm-tool

Kod Seç Genişlet

NetworkManager Tool

State: disconnected

- Device: eth1 -----------------------------------------------------------------
  Type:              Wired
  Driver:            forcedeth
  State:             unavailable
  Default:           no
  HW Address:        00:E0:4D:45:5B:D5

  Capabilities:
    Carrier Detect:  yes

  Wired Properties
    Carrier:         off


- Device: eth0 -----------------------------------------------------------------
  Type:              Wired
  Driver:            sundance
  State:             unavailable
  Default:           no
  HW Address:        F8:1A:67:00:C5:0D

  Capabilities:

  Wired Properties
    Carrier:         off

lspci -nnk | grep -iA2 net

Kod Seç Genişlet


00:07.0 Bridge [0680]: NVIDIA Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Subsystem: Biostar Microtech Int'l Corp Device [1565:2505]
Kernel driver in use: forcedeth
--
01:08.0 Ethernet controller [0200]: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY [13f0:0200] (rev 31)
Subsystem: Sundance Technology Inc / IC Plus Corp Device [13f0:0201]
Kernel driver in use: sundance


[if]

İki tane kablolu kart var. Biri Nvidia MCP61, kullandığı sürücü forecedeth. İlk defa böyle bir şey görüyorum:)
Diğer Sundance, kullandığı sürücü sundance.

Sundance kart için bu[1] konuda Wicd kullanımı işi çözmüş.

Şimdi önce sadece Sundance kullanmayı deneyelim. Fakat bu komutları ağ yöneticisini öldürmeden denemeniz gerek.

Kod Seç Genişlet

echo "blacklist forcedeth" | sudo tee -a /etc/modprobe.d/blacklist.conf
sudo modprobe -r forcedeth
sudo service network-manager restart
[1] https://forum.ubuntu-tr.net/index.php?topic=36964.0

[Gam Kenarı]

@if: Söylediklerinizi uyguladım, bilgisarayı iki kere resetleyip tekrar denedim ama değişen bir şey olmadı.

[heartsmagic]

Kod Seç Genişlet

lsmod | grep forcedeth

ne diyor şu an? BIOS üzerinden bu ağ kartını kapatma şansın var mı acaba?

[Gam Kenarı]

Çıktı şöyle:

Kod Seç Genişlet

forcedeth              62780  0

BIOS üzerinden ağ kartını kapatmayı bilmiyorum ama biraz araştırıp deneyebilirim.

[heartsmagic]

@if'in söyledikleri olmamış gibi.

Kod Seç Genişlet

cat /etc/modprobe.d/blacklist.conf
ne diyor?

[Gam Kenarı]

Kod Seç Genişlet

# This file lists those modules which we don't want to be loaded by
# alias expansion, usually so some other driver will be loaded for the
# device instead.

# evbug is a debug tool that should be loaded explicitly
blacklist evbug

# these drivers are very simple, the HID drivers are usually preferred
blacklist usbmouse
blacklist usbkbd

# replaced by e100
blacklist eepro100

# replaced by tulip
blacklist de4x5

# causes no end of confusion by creating unexpected network interfaces
blacklist eth1394

# snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much
# hardware on its own (Ubuntu bug #2011, #6810)
blacklist snd_intel8x0m

# Conflicts with dvb driver (which is better for handling this device)
blacklist snd_aw2

# causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306)
blacklist i2c_i801

# replaced by p54pci
blacklist prism54

# replaced by b43 and ssb.
blacklist bcm43xx

# most apps now use garmin usb driver directly (Ubuntu: #114565)
blacklist garmin_gps

# replaced by asus-laptop (Ubuntu: #184721)
blacklist asus_acpi

# low-quality, just noise when being used for sound playback, causes
# hangs at desktop session start (Ubuntu: #246969)
blacklist snd_pcsp

# ugly and loud noise, getting on everyone's nerves; this should be done by a
# nice pulseaudio bing (Ubuntu: #77010)
blacklist pcspkr

# EDAC driver for amd76x clashes with the agp driver preventing the aperture
# from being initialised (Ubuntu: #297750). Blacklist so that the driver
# continues to build and is installable for the few cases where its
# really needed.
blacklist amd76x_edac
blacklist forcedeth
blacklist forcedeth
blacklist forcedeth
blacklist forcedeth
blacklist forcedeth
blacklist forcedeth


[heartsmagic]

Kod Seç Genişlet

sudo -H mousepad /etc/modprobe.d/blacklist.conf

ile dosyayı açıp fazlalıkları siler misin? Bir satır kalsın sadece.

Not: Metin düzenleyici mousepad değil de başka bir şeyse onu kullanırsın.

Ardından sistemi bir yeniden başlat, sonra:

Kod Seç Genişlet

lsmod | grep force ile bir daha bakalım. Neden yüklendi modül acaba, fazla satır olsa bile yüklenmez diye düşünüyorum. Bir de şunu denediğinde ne diyor sistem sana:

Kod Seç Genişlet

sudo rmmod forcedeth

[Gam Kenarı]

@heartsmagic: Verrmiş olduğunuz ilk komutu terminalde yürüttüğümde  "sudo: mousepad: komut bulunamadı" diyor. Gedit ile açtım doğru yapmış mıyım?





Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 25 Mayıs 2014 - 01:46:34
lsmod | grep force

Kod Seç Genişlet

i2c_nforce2            13104  0
forcedeth              62780  0


sudo rmmod forcedeth
Bu komut herhangi bir çıktı vermedi.

[if]

Herhangi bir çıktı vermiyorsa sürücü kalkmıştır. Bu durumda bağlanamıyor musunuz?

[Gam Kenarı]

@if: Bilgisayarı resetleyip deneme yaptım ama aynı sorun devam ediyor. Ayrıca bilgisayar açılırken bir hata aldım.

[if]

O zaman,

Kod Seç Genişlet

sudo -H gedit /etc/modprobe.d/blacklist.conf ile dosyayı açın. forcedeth satırını silin. yerine sundance yazıp tekrar deneyelim.

[Gam Kenarı]

Söylediklerinizi yaptım değişen bir şey olmadı.  Ayrıca  "Error: Driver 'pcspkr' is already registered..." gibi bir hata almaya başladım.

Yeni hatırladım, ortalama 2 sene kadar önce yıldırım düşmesi sonucu anakartın ethernet girişi yanmıştı. Daha sonra yeni ethernet kartı alıp takmıştım. Bundan dolayı Ubuntu 12.04 sürümü, bu yanan ethernet kartınıda algılıyor galiba.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 25 Mayıs 2014 - 23:20:01



Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 25 Mayıs 2014 - 23:21:53
Arkadaşlar artık ağı hiç etkinleştiremiyorum,  "sudo pkill -9 NetworkManager" komutuda işe yaramıyor. Şu an internet cafeden yazıyorum. Ağ bağlantısını nasıl etkinleştirebilirim?

[heartsmagic]

BIOS ayarlarına hiç girdin mi? Orada belki imkân vardır tümleşik kartı kapatmak için. 

[if]

@Gam Kenarı,

Kod Seç Genişlet

sudo -H gedit /etc/modprobe.d/blacklist.conf dosyasını açıp eklediğimiz satırları silin

Kod Seç Genişlet

sudo modprobe forcedeth sundance ile sürücüleri yükleyin.

Hangisiydi yıldırım düşen kart?

[Gam Kenarı]

@heartsmagic: Evet BIOS ayarlarına girip biraz karıştırmıştım, tam olarak aradığımı bulamayınca pili çıkartıp BIOS'u sıfırlamıştım.

@if:  Nvidia olanına yıldırım düşmüştü. Şu an kullandığım ethernet kartının markası TP-LINK, ağ bağlantısına baktığımda ise ağ kartının adı Sundance Technology olarak gözüküyor. Sizce bu normal mi? Kusuruma bakmayın, bu konularda çok acemi olduğum için soruyorum.


Arkadaşlar bir önceki mesajımı yazdıktan sonra internet cafe sahibi cafeyi kapatacağı için hemen çıkmak zorunda kaldım. Bundan dolayı sizin cevaplarınızı okuma fırsatım olmadı.  Eve doğru gelirken aklıma Ubuntu 11.10 sürümünü kurduktan sonra 12.04 LTS sürümüne yükseltmek geldi. Belki böylece bu sorun ortadan kalkar diye düşünmüştüm. 11.10 kurduktan sonra yükseltme yaptım ama düşündüğüm gibi olmadı yine aynı sorunu yaşamaya başladım. 



Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 26 Mayıs 2014 - 16:22:24
Arkadaşlar sizlere çok teşekkür ederim, sorunu çözdüm. Aşağıda @if'in anlatıklarını uygularken hata yapıp  "Wicd"i kurmamışım. Biraz önce kurup bilgisayarı tekrar başlatınca sorunsuz bir şekilde  ağa bağlanabildim. Yalnız ne olur ne olmaz, ilerde sorun çıkarsa diye Networkmanager'i kaldırmadım, bu sorun olmaz herhalde?

İki tane kablolu kart var. Biri Nvidia MCP61, kullandığı sürücü forecedeth. İlk defa böyle bir şey görüyorum:)
Diğer Sundance, kullandığı sürücü sundance.

Sundance kart için bu[1] konuda Wicd kullanımı işi çözmüş.

Şimdi önce sadece Sundance kullanmayı deneyelim. Fakat bu komutları ağ yöneticisini öldürmeden denemeniz gerek.

Kod Seç Genişlet

echo "blacklist forcedeth" | sudo tee -a /etc/modprobe.d/blacklist.conf
sudo modprobe -r forcedeth
sudo service network-manager restart
[1] https://forum.ubuntu-tr.net/index.php?topic=36964.0

[heartsmagic]

Yok, sorun olmaz. Fakat Wicd nasıl başardı acaba bu işi diye merak ediyorum. Gerçi sıkıntı ağ yöneticisinde ki kendisini yeniden başlatınca sorun çözülüyor.