Asus k53sv Sdcard okuyucu sorunu

Başlatan FevziOztas, 30 Mart 2016 - 18:25:52

« önceki - sonraki »

0 Üyeler ve 1 Ziyaretçi konuyu incelemekte.

FevziOztas

Raw dosya biçimli Sd kartı pc ye taktığım zaman sd cardı görmüyor.
-lsusb yazdığımda sd card okuyucunun adını görebiliyorum RTS5139  ama kartı okumuyor.Realtekin sitesinde 5139 sayılı kart okuyucunun  driverı yok malesef. Ubuntu Raw dosya biçimini görmüyor olabilir mi ?
16Gb Sd Card takılı iken aldığım sonuçlar
Bus 004 Device 003: ID 09da:054f A4Tech Co., Ltd.
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 046d:c21d Logitech, Inc. F310 Gamepad [XInput Mode]
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 005: ID 0bda:0139 Realtek Semiconductor Corp. RTS5139 Card Reader Controller
Bus 003 Device 004: ID 058f:a014 Alcor Micro Corp. Asus Integrated Webcam
Bus 003 Device 006: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-fdisl -l
Disk /dev/sda: 750.2 GB, 750156374016 bytes
255 heads, 63 sectors/track, 91201 cylinders, toplam 1465149168 sektör
Units = sektör of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk kimlikleyicisi: 0xb4862712

   Aygıt Açılış    Başlangıç     Bitiş  BlokSayısı Kml Sistem
/dev/sda1            2048    52430847    26214400   1c  Gizli W95 FAT32 (LBA)
/dev/sda2   *    52430848   638488575   293028864    7  HPFS/NTFS/exFAT
/dev/sda3       638488576  1403705343   382608384    7  HPFS/NTFS/exFAT
/dev/sda4      1403707390  1465147391    30720001    5  Ek
Partition 4 does not start on physical sector boundary.
/dev/sda5      1403707392  1442766847    19529728   83  Linux
/dev/sda6      1442768896  1465147391    11189248   82  Linux takas / Solaris


-lsusb -vs 003:005
Bus 003 Device 005: ID 0bda:0139 Realtek Semiconductor Corp. RTS5139 Card Reader Controller
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass       255 Vendor Specific Subclass
  bDeviceProtocol       255 Vendor Specific Protocol
  bMaxPacketSize0        64
  idVendor           0x0bda Realtek Semiconductor Corp.
  idProduct          0x0139 RTS5139 Card Reader Controller
  bcdDevice           39.60
  iManufacturer           1
  iProduct                2
  iSerial                 3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      6
      bInterfaceProtocol     80
      iInterface              5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0003  1x 3 bytes
        bInterval              10








heartsmagic

Üzerinde bölüm yoksa görmemesi normal değil mi? 
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Alıntı yapılan: heartsmagic - 31 Mart 2016 - 14:51:02
Üzerinde bölüm yoksa görmemesi normal değil mi?
Anlamadım hocam sd kartı hiç görmüyor ubuntu o yüzden üzerinde bölüm oluşturamıyorum. Windowsa taktığım zaman ise raw dosya biçiminde olduğunu söylüyor. Açmaya çalıştığım zamanda biçimlendirmen gerek diyor, biçimlendir dediğimde ise kitleniyor.bu sebepten sd kartın üzerinde oynayamıyorum.Ubuntu üzerinden biçimlendirmek istiyorum ama görmediği için bişi yapamıyorum.

heartsmagic

Kartı taktıktan hemen sonra:
dmesg|tailçıktısını bir görebilir miyiz?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

#4
Öncelikle ilgilendiğiniz için teşekkür ederim hocam.Ayrılmamış derken ne demek istediğinizi yeni anladım Gparted ile baktığımda Sdkartı görebildim.Dediğiniz gibi ayrılmamış alan yazıyor.Gparted ile Aygıt sekmesinden yeni bölüm oluştur MSdos seçip daha sonra dosya sistemini fat 32 yada ntfs seçip bölüm oluştur dediğimde ise girdi çıktı hatası alıyorum. Yine biçimlendiremiyorum. Hem burda hemde Windowsda sd kartı görmemiz ama içini açamamamızın sebebi kart tan kaynaklı olabilirmi acaba ?
Kartı taktıktan hemen sonra yazdığımda aşağıdaki gibi bi sonuç aldım.
fevzi@fevzi-desktop:~$ dmesg|tail
[   26.713202] usb 3-1.1: new full-speed USB device number 6 using ehci-pci
[   26.806034] usb 3-1.1: New USB device found, idVendor=13d3, idProduct=3304
[   26.806038] usb 3-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   27.185977] usb 3-1.1: USB disconnect, device number 6
[   27.641966] usb 3-1.1: new full-speed USB device number 7 using ehci-pci
[   27.735068] usb 3-1.1: New USB device found, idVendor=0cf3, idProduct=3005
[   27.735071] usb 3-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[  318.427377] mmc0: card 0002 removed
[  321.667778] mmc0: new ultra high speed SDR50 SDHC card at address 0002
[  321.668476] mmcblk0: mmc0:0002 SD16G 14.9 GiB




heartsmagic

Eğer biçimlemeye çalışırken girdi/çıktı hatası veriyorsa muhtemelen kart bozulmuştur. Şu şekilde şansımızı deneyebiliriz ama:

sudo dd if=/dev/zero of=/dev/mmc0 bs=1M && sync

Tümden sıfırlamayı deneyecektir, yaparken çıktı vermez, başarılı olursa uçbirime düşüp ne kadar zamanda ne kadar yazabildiğini söyler sadece. Girdi/çıktı hatası verirse durum pek iç açıcı değildir. Eğer sorun yapmazsa tekrar takıp Gparted ile bölüm oluşturmayı bir denersin.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Anladım Hocam kodu girdiğimde şu sonucu aldım.Burdan bi sonuç çıkarabilirmiyiz acaba ?
Edit : Gparted ile tekrar bölüm oluşturmayı denedim yine aynı sonuç ile karşılaştım.
dd: `/dev/mmc0''e yazarken hata: Aygıt üzerinde boş yer yok
2929+0 kayıt girdi
2928+0 kayıt çıktı
3070373888 (3,1 GB) byte kopyalandı, 1,03786 s, 3,0 GB/s

heartsmagic

Kartı taktığında:
mount
ls -l /dev/mmcblk0
ne diyor?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

#8
Hocam il dışındaydım daha yeni döndüm kusura bakmayın.
Sonuç
fevzi@fevzi-desktop:~$ mount
/dev/sda5 on / type ext4 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
none on /sys/fs/cgroup type tmpfs (rw)
none on /sys/fs/fuse/connections type fusectl (rw)
none on /sys/kernel/debug type debugfs (rw)
none on /sys/kernel/security type securityfs (rw)
udev on /dev type devtmpfs (rw,mode=0755)
devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620)
tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755)
none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880)
none on /run/shm type tmpfs (rw,nosuid,nodev)
none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755)
none on /sys/fs/pstore type pstore (rw)
systemd on /sys/fs/cgroup/systemd type cgroup (rw,noexec,nosuid,nodev,none,name=systemd)
gvfsd-fuse on /run/user/1000/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=fevzi)
fevzi@fevzi-desktop:~$ ls -l /dev/mmcblk0
brw-rw---- 1 root disk 179, 0 Nis 17 12:40 /dev/mmcblk0


heartsmagic

ls -l /dev/mmc0 ne diyor?

sudo umount /dev/mmcblk0
sudo dd if=/dev/zero of=/dev/mmc0 bs=1M && sync


şeklinde dener misin ayrıca?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

ls -l /dev/mmc0
Bu kodda iki farklı sonuç aldım.İlk yazdığımda bu sonucu
ls: /dev/mmc0'e erişilemedi: Böyle bir dosya ya da dizin yok
Daha sonra dmesg|tail yazarak mmc0 olup olmadığını kontrol ettim yukardaki iletideki gibi olduğunu gördüm.Sonra ikinci kez ls -l /dev/mmc0 bu kodu yazdığımda ise bu sonucu aldım
-rw-r--r-- 1 root root 3070373888 Nis 18 02:13 /dev/mmc0
Diğer sonuçlar ise şöyle çıktı
sudo umount /dev/mmcblk0
umount: /dev/mmcblk0: bağlanmadı

sudo dd if=/dev/zero of=/dev/mmc0 bs=1M && sync
dd: `/dev/mmc0''e yazarken hata: Aygıt üzerinde boş yer yok
2929+0 kayıt girdi
2928+0 kayıt çıktı
3070373888 (3,1 GB) byte kopyalandı, 0,905035 s, 3,4 GB/s



heartsmagic

Şu an dmesg çıktısında aşağıdaki satır görünmüyor mu peki?
mmcblk0: mmc0:0002 SD16G 14.9 GiB
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Şu an itibariyle yazdığımda aldığım sonuç.Sonuç niye önceki iletideki gibi çıkmadı anlayamadım ? Sdcart ile ilgili kısımlar değişmemiş ama geri kalan değişmiş.
fevzi@fevzi-desktop:~$ dmesg|tail
[   39.626952] bbswitch: disabling discrete graphics
[   39.626964] ACPI Warning: \_SB_.PCI0.PEGR.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150619/nsarguments-95)
[   48.588512] audit_printk_skb: 123 callbacks suppressed
[   48.588516] audit: type=1400 audit(1460974738.959:62): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1793 comm="apparmor_parser"
[   48.588523] audit: type=1400 audit(1460974738.959:63): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1793 comm="apparmor_parser"
[   48.588878] audit: type=1400 audit(1460974738.959:64): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1793 comm="apparmor_parser"
[ 1270.557688] mmc0: card 0002 removed
[ 1272.709451] mmc0: new ultra high speed SDR50 SDHC card at address 0002
[ 1272.710223] mmcblk0: mmc0:0002 SD16G 14.9 GiB
[ 1272.712808]  mmcblk0:

heartsmagic

sudo dd if=/dev/zero of=/dev/mmcblk0 bs=1M && sync şeklinde deneyip, komutu verdikten sonra hemen:
dmesg | tail
ile durumu bir gözlemler misin? Benzer sorunu yaşayan bir başkası da gdisk ile her şeyi silip, GPT oluşturma işini falan söylemiş. Bir de onunla şansını dene istersen.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

#14
Hocam  dmesg | tail komutu gittikçe ilginç sonuçlar vermeye başladı  :D diğer komutta benzer bir sonuc aldım.
fevzi@fevzi-desktop:~$ dmesg | tail
[  105.284167]  [<ffffffff81079c4a>] warn_slowpath_null+0x1a/0x20
[  105.284168]  [<ffffffff812281a7>] __blkdev_put+0x1f7/0x250
[  105.284170]  [<ffffffff81228ab0>] blkdev_put+0x50/0x120
[  105.284171]  [<ffffffff81228c35>] blkdev_close+0x25/0x30
[  105.284174]  [<ffffffff811f0824>] __fput+0xe4/0x210
[  105.284176]  [<ffffffff811f099e>] ____fput+0xe/0x10
[  105.284178]  [<ffffffff810960d7>] task_work_run+0x77/0x90
[  105.284180]  [<ffffffff81015e08>] do_notify_resume+0x58/0x80
[  105.284182]  [<ffffffff817c4284>] int_signal+0x12/0x17
[  105.284184] ---[ end trace 7aded6fee61af8a2 ]---

Add: `/dev/mmcblk0''e yazarken hata: Aygıt üzerinde boş yer yok
15273+0 kayıt girdi
15272+0 kayıt çıktı
16013852672 (16 GB) byte kopyalandı, 25,4036 s, 630 MB/s


Hocam çözümü yoksa sizi de daha fazla meşgul etmek istemem ben sadece Raw dosya biçimi linux üzerinden biçimlendirme yolu ile kurtarılıyor diye okumuştum onu denemek istedim.Sd kartı görmeyince sizlere danışmak istedim.

heartsmagic

dmesg'te gördüklerimiz kartla ilgili değil muhtemelen, ben açıkçası G/Ç hatası bekliyordum ama görünmüyor. Meşgul etmek sorun değil, vaktimiz varsa zaten geliyoruz buralara :) Kart sorunlu ise Linux da çare olamaz tabi. Şu durumda eğer uğraşmak istiyorsan bir de gdisk'i incele.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Tamam hocam bi inceliyim.Bi de hocam bu işlemleri yaptıktan sonra yada yazılım güncelleştirmesi yaptıktan sonra -hangisinden sonra olduğunu tam olarak bilmiyorum- ubuntu açılırken buna benzer bir ekran geliyor.Buda açılışı yavaşlatıyor.Bir kaç forumda bios üzerinden usb portlar kapatılarak çözülüyor gibi bişi denmiş.Ama daha önceleri açılırken böyle bir ekranla karşılaşmıyordum.Bu sorunun bizim yapmış olduğumuz işlemler ile bir alakası olabilirmi ?

Usb 4-1 Port3 over-current condition
Usb 4-1 Port4 over-current condition

heartsmagic

Yok, bizim işlemler sistem genelinde bir şey yapmıyor. Verdiğin hata da normalde sorunlu USB yuvaları için sanırım ama senin makineler için yanlış alarm gibi.
https://bbs.archlinux.org/viewtopic.php?id=165878
Burada bahsi geçmiş, takılmaya gerek yok. Bekleyen yer başka bir şey bile olabilir. Ubuntu sürümün neydi?
Ayrıca USB sürümü nedir, 2 mi 3 mü? Eğer 2 ise şunu deneyebiliriz:
http://askubuntu.com/questions/147555/over-current-condition-on-port-7-or-8
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

#18
2 tane usb 2.0 var bitane usb 3.0 var.Sorun  hangisinden  kaynaklanıyor bilmiyorum.Önce 800*600 çözönürlükte sonra 1366*768 de aynı yazıyı gösteriyor bi süre bekliyor.Önemli bi şey değilse kalsın hocam, ben sadece sanki biraz açılışı yavaşlatıyo gibi geldi ondan soruyum dedim.
Distributor ID: Ubuntu
Description: Ubuntu 14.04.4 LTS
Release: 14.04
Codename: trusty

heartsmagic

2.0 olanlardır muhtemelen, çözümü bir deneyelim zararı olmaz.

sudo -H gedit /etc/default/grub
şeklinde açacağın dosyadaki şu satırı:
Alıntı YapGRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
şu şekilde değiştir:
Alıntı YapGRUB_CMDLINE_LINUX_DEFAULT="quiet splash ehci_hcd.ignore_OC=1"
Ardından Grub'u güncelle:
sudo update-grub
Sonra sistemi yeniden başlat.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Hocam malesef değişimedi sonuç :( dmesg listesinde hata veren usbleride buldum açılırken gösterdiği iletideki rakamdan.Sadece o kısımları kopyalıyorum liste çok uzun çünkü.
[    2.084861] usb 4-1-port3: over-current condition
[    2.293068] usb 4-1-port4: over-current condition

fevzi@fevzi-desktop:~$ dmesg
[    2.084861] usb 4-1-port3: over-current condition
[    2.157241] usb 3-1.2: New USB device found, idVendor=058f, idProduct=a014
[    2.157251] usb 3-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[    2.157257] usb 3-1.2: Product: ASUS USB2.0 WebCam
[    2.157262] usb 3-1.2: Manufacturer: 04G6200086K1AN1AD000F2Y
[    2.236822] usb 3-1.4: new high-speed USB device number 5 using ehci-pci
[    2.293068] usb 4-1-port4: over-current condition
[    2.329740] usb 3-1.4: New USB device found, idVendor=0bda, idProduct=0139
[    2.329750] usb 3-1.4: New USB device strings: Mfr=1, Product=2, Seria


heartsmagic

cat /proc/cmdline
ile bir bakalım parametre ne durumda diye.

Muhtemelen bahsettiğimiz iki yuvadır bu, bence takılmaya gerek yok. Bekleyen kısım orası mıdır emin olmak lazım, onun için de dmesg çıktısını geçersin buraya.

dmesg > falanca

dersen, komutu verdiğin yerde falanca diye bir dosya oluşur, içeriğini de buraya aktarırsın.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Sonuçlar bu şekilde. Yaptığım değişiklik geçerli olmuş sanırım. Sonu bu şekilde quiet splash ehci_hcd.ignore_OC=1 çıktığına göre ?
BOOT_IMAGE=/boot/vmlinuz-4.2.0-35-generic root=UUID=823f1b11-6f63-47bd-a4c6-55cc9328ee9e ro quiet splash ehci_hcd.ignore_OC=1

Dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.2.0-35-generic (buildd@lgw01-58) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #40~14.04.1-Ubuntu SMP Fri Mar 18 16:37:35 UTC 2016 (Ubuntu 4.2.0-35.40~14.04.1-generic 4.2.8-ckt5)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-35-generic root=UUID=823f1b11-6f63-47bd-a4c6-55cc9328ee9e ro quiet splash ehci_hcd.ignore_OC=1
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: xstate_offset[2]: 0240, xstate_sizes[2]: 0100
[    0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x04: 'AVX registers'
[    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 0x340 bytes, using 'standard' format.
[    0.000000] x86/fpu: Using 'eager' FPU context switches.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000aabccfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000aabcd000-0x00000000aacf3fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000aacf4000-0x00000000aacf5fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000aacf6000-0x00000000aade7fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000aade8000-0x00000000aaf18fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000aaf19000-0x00000000aafe7fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000aafe8000-0x00000000aaffcfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000aaffd000-0x00000000aaffffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000ab000000-0x00000000af9fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed13fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed18000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff980000-0x00000000ffbfffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffd80000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000001cfdfffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUSTeK Computer Inc. K53SV/K53SV, BIOS K53SV.324 12/30/2011
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x1cfe00 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FE0000000 write-back
[    0.000000]   2 base 0A0000000 mask FF8000000 write-back
[    0.000000]   3 base 0A8000000 mask FFC000000 write-back
[    0.000000]   4 base 0AB000000 mask FFF000000 uncachable
[    0.000000]   5 base 100000000 mask F00000000 write-back
[    0.000000]   6 base 1E0000000 mask FE0000000 uncachable
[    0.000000]   7 base 1D0000000 mask FF0000000 uncachable
[    0.000000]   8 base 1CFE00000 mask FFFE00000 uncachable
[    0.000000]   9 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT 
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2GB, range: 512MB, type WB
[    0.000000] reg 2, base: 2560MB, range: 128MB, type WB
[    0.000000] reg 3, base: 2688MB, range: 64MB, type WB
[    0.000000] reg 4, base: 2736MB, range: 16MB, type UC
[    0.000000] reg 5, base: 4GB, range: 4GB, type WB
[    0.000000] reg 6, base: 7680MB, range: 512MB, type UC
[    0.000000] reg 7, base: 7424MB, range: 256MB, type UC
[    0.000000] reg 8, base: 7422MB, range: 2MB, type UC
[    0.000000] total RAM covered: 6062M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K chunk_size: 4M num_reg: 9  lose cover RAM: 0G
[    0.000000] New variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2GB, range: 512MB, type WB
[    0.000000] reg 2, base: 2560MB, range: 128MB, type WB
[    0.000000] reg 3, base: 2688MB, range: 32MB, type WB
[    0.000000] reg 4, base: 2720MB, range: 16MB, type WB
[    0.000000] reg 5, base: 4GB, range: 2GB, type WB
[    0.000000] reg 6, base: 6GB, range: 1GB, type WB
[    0.000000] reg 7, base: 7GB, range: 256MB, type WB
[    0.000000] reg 8, base: 7422MB, range: 2MB, type UC
[    0.000000] e820: update [mem 0xab000000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xaaffd max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fcc60-0x000fcc6f] mapped at [ffff8800000fcc60]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[    0.000000] reserving inaccessible SNB gfx pages
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01ff5000, 0x01ff5fff] PGTABLE
[    0.000000] BRK [0x01ff6000, 0x01ff6fff] PGTABLE
[    0.000000] BRK [0x01ff7000, 0x01ff7fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x1cfc00000-0x1cfdfffff]
[    0.000000]  [mem 0x1cfc00000-0x1cfdfffff] page 2M
[    0.000000] BRK [0x01ff8000, 0x01ff8fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x1c0000000-0x1cfbfffff]
[    0.000000]  [mem 0x1c0000000-0x1cfbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x1a0000000-0x1bfffffff]
[    0.000000]  [mem 0x1a0000000-0x1bfffffff] page 2M
[    0.000000] BRK [0x01ff9000, 0x01ff9fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x1fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x20200000-0x3fffffff]
[    0.000000]  [mem 0x20200000-0x3fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x40200000-0xaabccfff]
[    0.000000]  [mem 0x40200000-0xaa9fffff] page 2M
[    0.000000]  [mem 0xaaa00000-0xaabccfff] page 4k
[    0.000000] BRK [0x01ffa000, 0x01ffafff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xaacf4000-0xaacf5fff]
[    0.000000]  [mem 0xaacf4000-0xaacf5fff] page 4k
[    0.000000] init_memory_mapping: [mem 0xaade8000-0xaaf18fff]
[    0.000000]  [mem 0xaade8000-0xaaf18fff] page 4k
[    0.000000] init_memory_mapping: [mem 0xaafe8000-0xaaffcfff]
[    0.000000]  [mem 0xaafe8000-0xaaffcfff] page 4k
[    0.000000] init_memory_mapping: [mem 0x100000000-0x19fffffff]
[    0.000000]  [mem 0x100000000-0x19fffffff] page 2M
[    0.000000] RAMDISK: [mem 0x359f4000-0x36cf1fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F0430 000024 (v02 _ASUS_)
[    0.000000] ACPI: XSDT 0x00000000AAFFEE18 00006C (v01 _ASUS_ Notebook 06222004 MSFT 00010013)
[    0.000000] ACPI: FACP 0x00000000AAF9BD98 0000F4 (v04 _ASUS_ NoteBook 06222004 MSFT 00010013)
[    0.000000] ACPI: DSDT 0x00000000AAF7C018 00DCAC (v01 _ASUS_ NoteBook 00000000 INTL 20091112)
[    0.000000] ACPI: FACS 0x00000000AAFE5E40 000040
[    0.000000] ACPI: FACS 0x00000000AAFE5D40 000040
[    0.000000] ACPI: APIC 0x00000000AAFFDF18 0000CC (v02 _ASUS_ NoteBook 06222004 MSFT 00010013)
[    0.000000] ACPI: HPET 0x00000000AAFE6D18 000038 (v01 _ASUS_ NoteBook 06222004 AMI. 00000003)
[    0.000000] ACPI: ECDT 0x00000000AAFE5B18 0000C1 (v01 _ASUS_ NoteBook 06222004 AMI  00000000)
[    0.000000] ACPI: MCFG 0x00000000AAFE6C98 00003C (v01 _ASUS_ NoteBook 06222004 MSFT 00000097)
[    0.000000] ACPI: SSDT 0x00000000AAF7B018 0007DB (v01 PmRef  Cpu0Ist  00003000 INTL 20091112)
[    0.000000] ACPI: SSDT 0x00000000AAF7A018 000996 (v01 PmRef  CpuPm    00003000 INTL 20091112)
[    0.000000] ACPI: SLIC 0x00000000AAF9CC18 000176 (v01 _ASUS_ Notebook 06222004 ASUS 00000001)
[    0.000000] ACPI: SSDT 0x00000000AAF5EA98 0002EF (v01 SataRe SataTabl 00001000 INTL 20091112)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x00000001cfdfffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x1cfdf5000-0x1cfdf9fff]
[    0.000000]  [ffffea0000000000-ffffea00073fffff] PMD -> [ffff8801c9400000-ffff8801cf3fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001cfdfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009dfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.000000]   node   0: [mem 0x0000000020200000-0x000000003fffffff]
[    0.000000]   node   0: [mem 0x0000000040200000-0x00000000aabccfff]
[    0.000000]   node   0: [mem 0x00000000aacf4000-0x00000000aacf5fff]
[    0.000000]   node   0: [mem 0x00000000aade8000-0x00000000aaf18fff]
[    0.000000]   node   0: [mem 0x00000000aafe8000-0x00000000aaffcfff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x00000001cfdfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x00000001cfdfffff]
[    0.000000] On node 0 totalpages: 1550002
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 157 pages reserved
[    0.000000]   DMA zone: 3997 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10853 pages used for memmap
[    0.000000]   DMA32 zone: 694549 pages, LIFO batch:31
[    0.000000]   Normal zone: 13304 pages used for memmap
[    0.000000]   Normal zone: 851456 pages, LIFO batch:31
[    0.000000] Reserving Intel graphics stolen memory at 0xaba00000-0xaf9fffff
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 16 CPUs, 12 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x40000000-0x401fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xaabcd000-0xaacf3fff]
[    0.000000] PM: Registered nosave memory: [mem 0xaacf6000-0xaade7fff]
[    0.000000] PM: Registered nosave memory: [mem 0xaaf19000-0xaafe7fff]
[    0.000000] PM: Registered nosave memory: [mem 0xaaffd000-0xaaffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xab000000-0xaf9fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xafa00000-0xdfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe4000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed0ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed13fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed14000-0xfed17fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed18000-0xfed19fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff97ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff980000-0xffbfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffc00000-0xffd7ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffd80000-0xffffffff]
[    0.000000] e820: [mem 0xafa00000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:16 nr_node_ids:1
[    0.000000] PERCPU: Embedded 33 pages/cpu @ffff8801c9000000 s96728 r8192 d30248 u262144
[    0.000000] pcpu-alloc: s96728 r8192 d30248 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1525624
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-35-generic root=UUID=823f1b11-6f63-47bd-a4c6-55cc9328ee9e ro quiet splash ehci_hcd.ignore_OC=1
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 5996804K/6200008K available (7971K kernel code, 1244K rwdata, 3816K rodata, 1472K init, 1292K bss, 203204K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] Build-time adjustment of leaf fanout to 64.
[    0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=16.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=16
[    0.000000] NR_IRQS:16640 nr_irqs:552 16
[    0.000000] Offload RCU callbacks from all CPUs
[    0.000000] Offload RCU callbacks from CPUs: 0-15.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2394.620 MHz processor
[    0.000036] Calibrating delay loop (skipped), value calculated using timer frequency.. 4789.24 BogoMIPS (lpj=9578480)
[    0.000038] pid_max: default: 32768 minimum: 301
[    0.000044] ACPI: Core revision 20150619
[    0.010235] ACPI: All ACPI Tables successfully acquired
[    0.010256] Security Framework initialized
[    0.010269] AppArmor: AppArmor initialized
[    0.010270] Yama: becoming mindful.
[    0.010807] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.012454] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.013189] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.013200] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.013406] Initializing cgroup subsys blkio
[    0.013409] Initializing cgroup subsys memory
[    0.013417] Initializing cgroup subsys devices
[    0.013419] Initializing cgroup subsys freezer
[    0.013421] Initializing cgroup subsys net_cls
[    0.013423] Initializing cgroup subsys perf_event
[    0.013425] Initializing cgroup subsys net_prio
[    0.013427] Initializing cgroup subsys hugetlb
[    0.013448] CPU: Physical Processor ID: 0
[    0.013449] CPU: Processor Core ID: 0
[    0.013454] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.013455] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.013457] mce: CPU supports 7 MCE banks
[    0.013467] CPU0: Thermal monitoring enabled (TM1)
[    0.013474] process: using mwait in idle threads
[    0.013477] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[    0.013478] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[    0.013903] Freeing SMP alternatives memory: 28K (ffffffff81ea9000 - ffffffff81eb0000)
[    0.033556] ftrace: allocating 30994 entries in 122 pages
[    0.049115] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.049149] Switched APIC routing to physical flat.
[    0.049553] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.089389] TSC deadline timer enabled
[    0.089393] smpboot: CPU0: Intel(R) Core(TM) i5-2430M CPU @ 2.40GHz (fam: 06, model: 2a, stepping: 07)
[    0.089419] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, full-width counters, Intel PMU driver.
[    0.089439] perf_event_intel: PEBS disabled due to CPU errata, please upgrade microcode
[    0.089441] ... version:                3
[    0.089442] ... bit width:              48
[    0.089443] ... generic registers:      4
[    0.089444] ... value mask:             0000ffffffffffff
[    0.089445] ... max period:             0000ffffffffffff
[    0.089446] ... fixed-purpose events:   3
[    0.089447] ... event mask:             000000070000000f
[    0.090327] x86: Booting SMP configuration:
[    0.090329] .... node  #0, CPUs:        #1
[    0.093748] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.093845]   #2  #3
[    0.100407] x86: Booted up 1 node, 4 CPUs
[    0.100410] smpboot: Total of 4 processors activated (19156.96 BogoMIPS)
[    0.103709] devtmpfs: initialized
[    0.106410] evm: security.selinux
[    0.106412] evm: security.SMACK64
[    0.106413] evm: security.SMACK64EXEC
[    0.106414] evm: security.SMACK64TRANSMUTE
[    0.106415] evm: security.SMACK64MMAP
[    0.106415] evm: security.ima
[    0.106416] evm: security.capability
[    0.106478] PM: Registering ACPI NVS region [mem 0xaaf19000-0xaafe7fff] (847872 bytes)
[    0.106574] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.106662] pinctrl core: initialized pinctrl subsystem
[    0.106775] RTC time: 17:45:43, date: 04/21/16
[    0.106890] NET: Registered protocol family 16
[    0.111528] cpuidle: using governor ladder
[    0.115533] cpuidle: using governor menu
[    0.115681] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.115683] ACPI: bus type PCI registered
[    0.115685] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.115767] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.115769] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[    0.115775] PCI: Using configuration type 1 for base access
[    0.116001] perf_event_intel: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.119967] ACPI: Added _OSI(Module Device)
[    0.119969] ACPI: Added _OSI(Processor Device)
[    0.119970] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.119971] ACPI: Added _OSI(Processor Aggregator Device)
[    0.121542] ACPI : EC: EC description table is found, configuring boot EC
[    0.121604] ACPI : EC: EC started
[    0.123328] ACPI: Executed 1 blocks of module-level executable AML code
[    0.125840] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.180224] ACPI: Dynamic OEM Table Load:
[    0.180231] ACPI: SSDT 0xFFFF8801C7AC2800 00073F (v01 PmRef  Cpu0Cst  00003001 INTL 20091112)
[    0.180806] ACPI: Dynamic OEM Table Load:
[    0.180811] ACPI: SSDT 0xFFFF8801C7ABD800 000303 (v01 PmRef  ApIst    00003000 INTL 20091112)
[    0.181315] ACPI: Dynamic OEM Table Load:
[    0.181319] ACPI: SSDT 0xFFFF8801C7AB7C00 000119 (v01 PmRef  ApCst    00003000 INTL 20091112)
[    0.182180] ACPI: Interpreter enabled
[    0.182190] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[    0.182203] ACPI: (supports S0 S1 S3 S4 S5)
[    0.182204] ACPI: Using IOAPIC for interrupt routing
[    0.182228] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.298308] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.298314] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.298345] \_SB_.PCI0:_OSC invalid UUID
[    0.298347] _OSC request data:1 1f 0
[    0.298350] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.298736] PCI host bridge to bus 0000:00
[    0.298739] pci_bus 0000:00: root bus resource [bus 00-3e]
[    0.298741] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.298743] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.298745] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.298747] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    0.298748] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    0.298750] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    0.298751] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    0.298753] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[    0.298755] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[    0.298756] pci_bus 0000:00: root bus resource [mem 0xafa00000-0xfeafffff window]
[    0.298758] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff window]
[    0.298765] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[    0.298854] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[    0.298884] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.298924] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.298965] pci 0000:00:02.0: [8086:0116] type 00 class 0x030000
[    0.298974] pci 0000:00:02.0: reg 0x10: [mem 0xdc400000-0xdc7fffff 64bit]
[    0.298980] pci 0000:00:02.0: reg 0x18: [mem 0xb0000000-0xbfffffff 64bit pref]
[    0.298984] pci 0000:00:02.0: reg 0x20: [io  0xe000-0xe03f]
[    0.299102] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[    0.299124] pci 0000:00:16.0: reg 0x10: [mem 0xdf00a000-0xdf00a00f 64bit]
[    0.299196] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.299282] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[    0.299300] pci 0000:00:1a.0: reg 0x10: [mem 0xdf008000-0xdf0083ff]
[    0.299379] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.299434] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.299476] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[    0.299493] pci 0000:00:1b.0: reg 0x10: [mem 0xdf000000-0xdf003fff 64bit]
[    0.299561] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.299641] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[    0.299712] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.299793] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[    0.299870] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.299953] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[    0.300023] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.300104] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
[    0.300174] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.300256] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[    0.300274] pci 0000:00:1d.0: reg 0x10: [mem 0xdf007000-0xdf0073ff]
[    0.300354] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.300408] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.300448] pci 0000:00:1f.0: [8086:1c49] type 00 class 0x060100
[    0.300619] pci 0000:00:1f.2: [8086:1c03] type 00 class 0x010601
[    0.300635] pci 0000:00:1f.2: reg 0x10: [io  0xe0b0-0xe0b7]
[    0.300643] pci 0000:00:1f.2: reg 0x14: [io  0xe0a0-0xe0a3]
[    0.300651] pci 0000:00:1f.2: reg 0x18: [io  0xe090-0xe097]
[    0.300660] pci 0000:00:1f.2: reg 0x1c: [io  0xe080-0xe083]
[    0.300668] pci 0000:00:1f.2: reg 0x20: [io  0xe060-0xe07f]
[    0.300676] pci 0000:00:1f.2: reg 0x24: [mem 0xdf006000-0xdf0067ff]
[    0.300713] pci 0000:00:1f.2: PME# supported from D3hot
[    0.300786] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.300802] pci 0000:00:1f.3: reg 0x10: [mem 0xdf005000-0xdf0050ff 64bit]
[    0.300823] pci 0000:00:1f.3: reg 0x20: [io  0xe040-0xe05f]
[    0.300953] pci 0000:01:00.0: [10de:0df4] type 00 class 0x030000
[    0.300962] pci 0000:01:00.0: reg 0x10: [mem 0xdb000000-0xdbffffff]
[    0.300969] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.300977] pci 0000:01:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    0.300981] pci 0000:01:00.0: reg 0x24: [io  0xd000-0xd07f]
[    0.300986] pci 0000:01:00.0: reg 0x30: [mem 0xdc000000-0xdc07ffff pref]
[    0.301051] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.307860] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.307868] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.307875] pci 0000:00:01.0:   bridge window [mem 0xdb000000-0xdc0fffff]
[    0.307884] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.307986] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.307990] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.307995] pci 0000:00:1c.0:   bridge window [mem 0xde600000-0xdeffffff]
[    0.308001] pci 0000:00:1c.0:   bridge window [mem 0xd4200000-0xd4bfffff 64bit pref]
[    0.308070] pci 0000:03:00.0: [168c:002b] type 00 class 0x028000
[    0.308101] pci 0000:03:00.0: reg 0x10: [mem 0xddc00000-0xddc0ffff 64bit]
[    0.308242] pci 0000:03:00.0: supports D1
[    0.308243] pci 0000:03:00.0: PME# supported from D0 D1 D3hot D3cold
[    0.308273] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.315879] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.315889] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.315899] pci 0000:00:1c.1:   bridge window [mem 0xddc00000-0xde5fffff]
[    0.315913] pci 0000:00:1c.1:   bridge window [mem 0xd3700000-0xd40fffff 64bit pref]
[    0.316032] pci 0000:04:00.0: [1b21:1042] type 00 class 0x0c0330
[    0.316071] pci 0000:04:00.0: reg 0x10: [mem 0xdd200000-0xdd207fff 64bit]
[    0.316253] pci 0000:04:00.0: PME# supported from D3hot D3cold
[    0.316285] pci 0000:04:00.0: System wakeup disabled by ACPI
[    0.323904] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.323914] pci 0000:00:1c.3:   bridge window [io  0xa000-0xafff]
[    0.323923] pci 0000:00:1c.3:   bridge window [mem 0xdd200000-0xddbfffff]
[    0.323936] pci 0000:00:1c.3:   bridge window [mem 0xd2c00000-0xd35fffff 64bit pref]
[    0.324048] pci 0000:05:00.0: [10ec:8168] type 00 class 0x020000
[    0.324072] pci 0000:05:00.0: reg 0x10: [io  0x9000-0x90ff]
[    0.324107] pci 0000:05:00.0: reg 0x18: [mem 0xd2104000-0xd2104fff 64bit pref]
[    0.324129] pci 0000:05:00.0: reg 0x20: [mem 0xd2100000-0xd2103fff 64bit pref]
[    0.324224] pci 0000:05:00.0: supports D1 D2
[    0.324226] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.324259] pci 0000:05:00.0: System wakeup disabled by ACPI
[    0.331909] pci 0000:00:1c.5: PCI bridge to [bus 05]
[    0.331919] pci 0000:00:1c.5:   bridge window [io  0x9000-0x9fff]
[    0.331928] pci 0000:00:1c.5:   bridge window [mem 0xdc800000-0xdd1fffff]
[    0.331941] pci 0000:00:1c.5:   bridge window [mem 0xd2100000-0xd2afffff 64bit pref]
[    0.388175] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.388224] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.388271] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.388317] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[    0.388365] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.388412] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.388462] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 *3 4 5 6 10 11 12 14 15)
[    0.388508] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 *4 5 6 10 11 12 14 15)
[    0.388620] ACPI: Enabled 2 GPEs in block 00 to 3F
[    0.388669] ACPI : EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[    0.388775] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.388777] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.388781] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[    0.388782] vgaarb: loaded
[    0.388783] vgaarb: bridge control possible 0000:01:00.0
[    0.388784] vgaarb: no bridge control possible 0000:00:02.0
[    0.389021] SCSI subsystem initialized
[    0.389068] libata version 3.00 loaded.
[    0.389092] ACPI: bus type USB registered
[    0.389109] usbcore: registered new interface driver usbfs
[    0.389117] usbcore: registered new interface driver hub
[    0.389136] usbcore: registered new device driver usb
[    0.389279] PCI: Using ACPI for IRQ routing
[    0.390744] PCI: pci_cache_line_size set to 64 bytes
[    0.390801] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[    0.390803] e820: reserve RAM buffer [mem 0xaabcd000-0xabffffff]
[    0.390804] e820: reserve RAM buffer [mem 0xaacf6000-0xabffffff]
[    0.390806] e820: reserve RAM buffer [mem 0xaaf19000-0xabffffff]
[    0.390807] e820: reserve RAM buffer [mem 0xaaffd000-0xabffffff]
[    0.390808] e820: reserve RAM buffer [mem 0x1cfe00000-0x1cfffffff]
[    0.390925] NetLabel: Initializing
[    0.390926] NetLabel:  domain hash size = 128
[    0.390927] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.390940] NetLabel:  unlabeled traffic allowed by default
[    0.391016] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.391021] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.394055] clocksource: Switched to clocksource hpet
[    0.399760] AppArmor: AppArmor Filesystem Enabled
[    0.399833] pnp: PnP ACPI init
[    0.399961] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.399964] system 00:00: [io  0x1000-0x100f] has been reserved
[    0.399966] system 00:00: [io  0xffff] has been reserved
[    0.399968] system 00:00: [io  0xffff] has been reserved
[    0.399970] system 00:00: [io  0x0400-0x0453] could not be reserved
[    0.399971] system 00:00: [io  0x0458-0x047f] has been reserved
[    0.399973] system 00:00: [io  0x0500-0x057f] has been reserved
[    0.399975] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.399979] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.400004] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.400044] system 00:02: [io  0x0454-0x0457] has been reserved
[    0.400047] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.400088] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.400135] pnp 00:04: Plug and Play ACPI device, IDs SYN0a17 SYN0a00 SYN0002 PNP0f13 (active)
[    0.454389] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.454391] system 00:05: [mem 0xfed10000-0xfed17fff] could not be reserved
[    0.454393] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.454395] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.454397] system 00:05: [mem 0xe0000000-0xe3ffffff] has been reserved
[    0.454399] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.454400] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.454402] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.454404] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[    0.454406] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.454408] system 00:05: [mem 0xafa00000-0xafa00fff] has been reserved
[    0.454411] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.454458] system 00:06: [mem 0xafa00000-0xafa00fff] has been reserved
[    0.454461] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.454575] system 00:07: [mem 0x20000000-0x201fffff] has been reserved
[    0.454577] system 00:07: [mem 0x40000000-0x401fffff] has been reserved
[    0.454580] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.454590] pnp: PnP ACPI: found 8 devices
[    0.460911] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.460952] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.460954] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.460957] pci 0000:00:01.0:   bridge window [mem 0xdb000000-0xdc0fffff]
[    0.460960] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.460963] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.460966] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.460972] pci 0000:00:1c.0:   bridge window [mem 0xde600000-0xdeffffff]
[    0.460976] pci 0000:00:1c.0:   bridge window [mem 0xd4200000-0xd4bfffff 64bit pref]
[    0.460982] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.460986] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.460991] pci 0000:00:1c.1:   bridge window [mem 0xddc00000-0xde5fffff]
[    0.460995] pci 0000:00:1c.1:   bridge window [mem 0xd3700000-0xd40fffff 64bit pref]
[    0.461002] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.461005] pci 0000:00:1c.3:   bridge window [io  0xa000-0xafff]
[    0.461010] pci 0000:00:1c.3:   bridge window [mem 0xdd200000-0xddbfffff]
[    0.461014] pci 0000:00:1c.3:   bridge window [mem 0xd2c00000-0xd35fffff 64bit pref]
[    0.461020] pci 0000:00:1c.5: PCI bridge to [bus 05]
[    0.461023] pci 0000:00:1c.5:   bridge window [io  0x9000-0x9fff]
[    0.461028] pci 0000:00:1c.5:   bridge window [mem 0xdc800000-0xdd1fffff]
[    0.461033] pci 0000:00:1c.5:   bridge window [mem 0xd2100000-0xd2afffff 64bit pref]
[    0.461040] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.461042] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.461044] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.461046] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[    0.461047] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[    0.461049] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[    0.461050] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[    0.461052] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[    0.461054] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[    0.461055] pci_bus 0000:00: resource 13 [mem 0xafa00000-0xfeafffff window]
[    0.461057] pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed44fff window]
[    0.461059] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.461061] pci_bus 0000:01: resource 1 [mem 0xdb000000-0xdc0fffff]
[    0.461062] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.461064] pci_bus 0000:02: resource 0 [io  0xc000-0xcfff]
[    0.461066] pci_bus 0000:02: resource 1 [mem 0xde600000-0xdeffffff]
[    0.461067] pci_bus 0000:02: resource 2 [mem 0xd4200000-0xd4bfffff 64bit pref]
[    0.461069] pci_bus 0000:03: resource 0 [io  0xb000-0xbfff]
[    0.461071] pci_bus 0000:03: resource 1 [mem 0xddc00000-0xde5fffff]
[    0.461072] pci_bus 0000:03: resource 2 [mem 0xd3700000-0xd40fffff 64bit pref]
[    0.461074] pci_bus 0000:04: resource 0 [io  0xa000-0xafff]
[    0.461076] pci_bus 0000:04: resource 1 [mem 0xdd200000-0xddbfffff]
[    0.461077] pci_bus 0000:04: resource 2 [mem 0xd2c00000-0xd35fffff 64bit pref]
[    0.461079] pci_bus 0000:05: resource 0 [io  0x9000-0x9fff]
[    0.461080] pci_bus 0000:05: resource 1 [mem 0xdc800000-0xdd1fffff]
[    0.461082] pci_bus 0000:05: resource 2 [mem 0xd2100000-0xd2afffff 64bit pref]
[    0.461118] NET: Registered protocol family 2
[    0.461295] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    0.461451] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.461572] TCP: Hash tables configured (established 65536 bind 65536)
[    0.461607] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.461638] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.461718] NET: Registered protocol family 1
[    0.461735] pci 0000:00:02.0: Video device with shadowed ROM
[    0.710648] PCI: CLS 64 bytes, default 64
[    0.710705] Trying to unpack rootfs image as initramfs...
[    1.022567] Freeing initrd memory: 19448K (ffff8800359f4000 - ffff880036cf2000)
[    1.022579] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.022581] software IO TLB [mem 0xa6bcd000-0xaabcd000] (64MB) mapped at [ffff8800a6bcd000-ffff8800aabccfff]
[    1.022688] RAPL PMU detected, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer
[    1.022690] hw unit of domain pp0-core 2^-16 Joules
[    1.022691] hw unit of domain package 2^-16 Joules
[    1.022692] hw unit of domain pp1-gpu 2^-16 Joules
[    1.022759] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x1b
[    1.022767] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x1b
[    1.022775] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x1b
[    1.022785] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x1b
[    1.022838] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.022919] Scanning for low memory corruption every 60 seconds
[    1.023374] futex hash table entries: 4096 (order: 6, 262144 bytes)
[    1.023412] Initialise system trusted keyring
[    1.023432] audit: initializing netlink subsys (disabled)
[    1.023446] audit: type=2000 audit(1461260744.004:1): initialized
[    1.023794] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.025261] zpool: loaded
[    1.025264] zbud: loaded
[    1.025456] VFS: Disk quotas dquot_6.6.0
[    1.025495] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.025953] fuse init (API version 7.23)
[    1.026086] Key type big_key registered
[    1.026463] Key type asymmetric registered
[    1.026468] Asymmetric key parser 'x509' registered
[    1.026485] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.026526] io scheduler noop registered
[    1.026531] io scheduler deadline registered (default)
[    1.026562] io scheduler cfq registered
[    1.027143] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.027150] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.027184] intel_idle: MWAIT substates: 0x21120
[    1.027185] intel_idle: v0.4 model 0x2A
[    1.027186] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.027389] ACPI: AC Adapter [AC0] (on-line)
[    1.027461] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    1.028525] ACPI: Lid Switch [LID]
[    1.028563] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    1.028567] ACPI: Sleep Button [SLPB]
[    1.028601] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    1.028602] ACPI: Power Button [PWRF]
[    1.029301] thermal LNXTHERM:00: registered as thermal_zone0
[    1.029303] ACPI: Thermal Zone [TZ00] (37 C)
[    1.029347] GHES: HEST is not enabled!
[    1.029359] ACPI: Battery Slot [BAT0] (battery absent)
[    1.029474] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    1.031033] Linux agpgart interface v0.103
[    1.033264] brd: module loaded
[    1.034183] loop: module loaded
[    1.034394] libphy: Fixed MDIO Bus: probed
[    1.034398] tun: Universal TUN/TAP device driver, 1.6
[    1.034399] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.034442] PPP generic driver version 2.4.2
[    1.034582] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    1.034588] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
[    1.039041] xhci_hcd 0000:04:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[    1.039219] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.039221] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.039223] usb usb1: Product: xHCI Host Controller
[    1.039224] usb usb1: Manufacturer: Linux 4.2.0-35-generic xhci-hcd
[    1.039226] usb usb1: SerialNumber: 0000:04:00.0
[    1.039360] hub 1-0:1.0: USB hub found
[    1.039371] hub 1-0:1.0: 2 ports detected
[    1.039455] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    1.039459] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2
[    1.039483] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.039499] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    1.039501] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.039502] usb usb2: Product: xHCI Host Controller
[    1.039504] usb usb2: Manufacturer: Linux 4.2.0-35-generic xhci-hcd
[    1.039505] usb usb2: SerialNumber: 0000:04:00.0
[    1.039628] hub 2-0:1.0: USB hub found
[    1.039637] hub 2-0:1.0: 2 ports detected
[    1.039721] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.039727] ehci-pci: EHCI PCI platform driver
[    1.039821] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    1.039826] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    1.039837] ehci-pci 0000:00:1a.0: debug port 2
[    1.043742] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    1.043751] ehci-pci 0000:00:1a.0: irq 16, io mem 0xdf008000
[    1.054624] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.054650] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    1.054652] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.054654] usb usb3: Product: EHCI Host Controller
[    1.054655] usb usb3: Manufacturer: Linux 4.2.0-35-generic ehci_hcd
[    1.054657] usb usb3: SerialNumber: 0000:00:1a.0
[    1.054802] hub 3-0:1.0: USB hub found
[    1.054807] hub 3-0:1.0: 2 ports detected
[    1.054972] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.054978] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[    1.054989] ehci-pci 0000:00:1d.0: debug port 2
[    1.058892] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.058900] ehci-pci 0000:00:1d.0: irq 23, io mem 0xdf007000
[    1.070644] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.070669] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    1.070671] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.070672] usb usb4: Product: EHCI Host Controller
[    1.070674] usb usb4: Manufacturer: Linux 4.2.0-35-generic ehci_hcd
[    1.070675] usb usb4: SerialNumber: 0000:00:1d.0
[    1.070821] hub 4-0:1.0: USB hub found
[    1.070827] hub 4-0:1.0: 2 ports detected
[    1.070912] ehci-platform: EHCI generic platform driver
[    1.070922] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.070928] ohci-pci: OHCI PCI platform driver
[    1.070938] ohci-platform: OHCI generic platform driver
[    1.070948] uhci_hcd: USB Universal Host Controller Interface driver
[    1.071004] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.072857] i8042: Detected active multiplexing controller, rev 1.1
[    1.073672] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.073676] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.073705] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.073730] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.073757] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.074097] mousedev: PS/2 mouse device common for all mice
[    1.074693] rtc_cmos 00:01: RTC can wake from S4
[    1.074860] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.074889] rtc_cmos 00:01: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    1.074897] i2c /dev entries driver
[    1.074972] device-mapper: uevent: version 1.0.3
[    1.075103] device-mapper: ioctl: 4.33.0-ioctl (2015-8-18) initialised: dm-devel@redhat.com
[    1.075118] Intel P-state driver initializing.
[    1.075309] ledtrig-cpu: registered to indicate activity on CPUs
[    1.075785] PCCT header not found.
[    1.076408] NET: Registered protocol family 10
[    1.076918] NET: Registered protocol family 17
[    1.076953] Key type dns_resolver registered
[    1.077981] Loading compiled-in X.509 certificates
[    1.080753] Loaded X.509 cert 'Build time autogenerated kernel key: 78a2b17e20a39676a35e2c3e160e701f99e0659b'
[    1.080793] registered taskstats version 1
[    1.080856] zswap: loading zswap
[    1.080861] zswap: using zbud pool
[    1.080873] zswap: using lzo compressor
[    1.086367] Key type trusted registered
[    1.093195] Key type encrypted registered
[    1.093202] AppArmor: AppArmor sha1 policy hashing enabled
[    1.093206] ima: No TPM chip found, activating TPM-bypass!
[    1.093224] evm: HMAC attrs: 0x1
[    1.093616]   Magic number: 12:604:795
[    1.093728] rtc_cmos 00:01: setting system clock to 2016-04-21 17:45:44 UTC (1461260744)
[    1.093820] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.093821] EDD information not available.
[    1.093899] PM: Hibernation image not present or could not be loaded.
[    1.094187] Freeing unused kernel memory: 1472K (ffffffff81d39000 - ffffffff81ea9000)
[    1.094188] Write protecting the kernel read-only data: 12288k
[    1.094350] Freeing unused kernel memory: 208K (ffff8800017cc000 - ffff880001800000)
[    1.094427] Freeing unused kernel memory: 280K (ffff880001bba000 - ffff880001c00000)
[    1.102778] systemd-udevd[120]: starting version 204
[    1.110999] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.125225] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.125235] r8169 0000:05:00.0: can't disable ASPM; OS doesn't have ASPM control
[    1.125601] r8169 0000:05:00.0 eth0: RTL8168e/8111e at 0xffffc90000efa000, 54:04:a6:34:c9:bb, XID 0c200000 IRQ 30
[    1.125603] r8169 0000:05:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.127040] ahci 0000:00:1f.2: version 3.0
[    1.127215] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
[    1.127219] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
[    1.135720] scsi host0: ahci
[    1.136491] scsi host1: ahci
[    1.136626] scsi host2: ahci
[    1.138530] scsi host3: ahci
[    1.139521] scsi host4: ahci
[    1.139653] scsi host5: ahci
[    1.139731] ata1: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006100 irq 31
[    1.139735] ata2: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006180 irq 31
[    1.139737] ata3: DUMMY
[    1.139738] ata4: DUMMY
[    1.139739] ata5: DUMMY
[    1.139740] ata6: DUMMY
[    1.366994] usb 3-1: new high-speed USB device number 2 using ehci-pci
[    1.383006] usb 4-1: new high-speed USB device number 2 using ehci-pci
[    1.407012] usb 1-1: new full-speed USB device number 2 using xhci_hcd
[    1.459095] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.459145] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.460929] ata2.00: ATAPI: MATSHITADVD-RAM UJ8B0, 1.00, max UDMA/100
[    1.463202] ata2.00: configured for UDMA/100
[    1.464557] ata1.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[    1.464568] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.464574] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.470199] ata1.00: ATA-8: WDC WD7500BPVT-80HXZT3, 01.01A01, max UDMA/133
[    1.470209] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.475982] ata1.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[    1.475994] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.476001] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.481524] ata1.00: configured for UDMA/133
[    1.481776] scsi 0:0:0:0: Direct-Access     ATA      WDC WD7500BPVT-8 1A01 PQ: 0 ANSI: 5
[    1.482083] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
[    1.482087] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.482104] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.482181] sd 0:0:0:0: [sda] Write Protect is off
[    1.482184] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.482219] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.483735] scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ8B0    1.00 PQ: 0 ANSI: 5
[    1.499477] usb 3-1: New USB device found, idVendor=8087, idProduct=0024
[    1.499481] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.499880] hub 3-1:1.0: USB hub found
[    1.499980] hub 3-1:1.0: 6 ports detected
[    1.500600] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.500603] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.500714] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.500774] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.515605] usb 4-1: New USB device found, idVendor=8087, idProduct=0024
[    1.515614] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.515990] hub 4-1:1.0: USB hub found
[    1.516132] hub 4-1:1.0: 6 ports detected
[    1.550608]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[    1.551338] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.595689] usb 1-1: New USB device found, idVendor=046d, idProduct=c21d
[    1.595699] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.595705] usb 1-1: Product: Gamepad F310
[    1.595710] usb 1-1: Manufacturer: Logitech
[    1.595714] usb 1-1: SerialNumber: C15028A6
[    1.771298] usb 3-1.1: new full-speed USB device number 3 using ehci-pci
[    1.787265] usb 4-1.2: new full-speed USB device number 3 using ehci-pci
[    1.864263] usb 3-1.1: New USB device found, idVendor=13d3, idProduct=3304
[    1.864274] usb 3-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.881818] usb 4-1.2: New USB device found, idVendor=09da, idProduct=054f
[    1.881828] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.881833] usb 4-1.2: Product: USB Device
[    1.881838] usb 4-1.2: Manufacturer: A4TECH
[    1.884969] hidraw: raw HID events driver (C) Jiri Kosina
[    1.888838] usbcore: registered new interface driver usbhid
[    1.888840] usbhid: USB HID core driver
[    1.890294] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/0003:09DA:054F.0001/input/input12
[    1.935379] usb 3-1.2: new high-speed USB device number 4 using ehci-pci
[    1.943713] hid-generic 0003:09DA:054F.0001: input,hiddev0,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.0-1.2/input0
[    1.943831] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.1/0003:09DA:054F.0002/input/input13
[    1.944018] hid-generic 0003:09DA:054F.0002: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.0-1.2/input1
[    2.023451] tsc: Refined TSC clocksource calibration: 2394.560 MHz
[    2.023453] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2284248580e, max_idle_ns: 440795288736 ns
[    2.087766] usb 4-1-port3: over-current condition
[    2.160401] usb 3-1.2: New USB device found, idVendor=058f, idProduct=a014
[    2.160412] usb 3-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[    2.160418] usb 3-1.2: Product: ASUS USB2.0 WebCam
[    2.160423] usb 3-1.2: Manufacturer: 04G6200086K1AN1AD000F2Y
[    2.239657] usb 3-1.4: new high-speed USB device number 5 using ehci-pci
[    2.295944] usb 4-1-port4: over-current condition
[    2.332782] usb 3-1.4: New USB device found, idVendor=0bda, idProduct=0139
[    2.332785] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.332787] usb 3-1.4: Product: USB2.0-CRW
[    2.332788] usb 3-1.4: Manufacturer: Generic
[    2.332789] usb 3-1.4: SerialNumber: 20100201396000000
[    2.337468] usbcore: registered new interface driver rtsx_usb
[    2.745594] random: nonblocking pool is initialized
[    3.024487] clocksource: Switched to clocksource tsc
[    3.472591] mmc0: new ultra high speed SDR50 SDHC card at address 0002
[    3.474277] mmcblk0: mmc0:0002 SD16G 14.9 GiB
[    3.882867] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   15.351150] Adding 11189244k swap on /dev/sda6.  Priority:-1 extents:1 across:11189244k FS
[   15.507365] systemd-udevd[315]: starting version 204
[   15.652437] lp: driver loaded but no devices found
[   15.657044] ppdev: user-space parallel port driver
[   15.683363] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   15.694886] [drm] Initialized drm 1.1.0 20060810
[   15.708707] wmi: Mapper loaded
[   15.724672] [drm] Memory usable by graphics device = 2048M
[   15.724676] [drm] Replacing VGA console driver
[   15.725218] Console: switching to colour dummy device 80x25
[   15.731429] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   15.731432] [drm] Driver supports precise vblank timestamp query.
[   15.731600] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   15.752279] Bluetooth: Core ver 2.20
[   15.752294] NET: Registered protocol family 31
[   15.752296] Bluetooth: HCI device and connection manager initialized
[   15.752300] Bluetooth: HCI socket layer initialized
[   15.752303] Bluetooth: L2CAP socket layer initialized
[   15.752309] Bluetooth: SCO socket layer initialized
[   15.773827] usbcore: registered new interface driver btusb
[   15.775560] ACPI: Video Device [GFX0] (multi-head: yes  rom: yes  post: no)
[   15.777212] acpi device:50: registered as cooling_device4
[   15.777297] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:4c/LNXVIDEO:00/input/input14
[   15.784374] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   15.785883] acpi device:52: registered as cooling_device5
[   15.785965] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input15
[   15.786614] [drm] Initialized i915 1.6.0 20150522 for 0000:00:02.0 on minor 0
[   15.786729] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20150619/utaddress-254)
[   15.786737] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.786741] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000549 (\SBGP) (20150619/utaddress-254)
[   15.786744] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150619/utaddress-254)
[   15.786748] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.786749] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000549 (\SBGP) (20150619/utaddress-254)
[   15.786753] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150619/utaddress-254)
[   15.786756] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.786757] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000549 (\SBGP) (20150619/utaddress-254)
[   15.786760] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150619/utaddress-254)
[   15.786763] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.786765] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   15.787122] fbcon: inteldrmfb (fb0) is primary device
[   15.820287] AVX version of gcm_enc/dec engaged.
[   15.820288] AES CTR mode by8 optimization enabled
[   15.826170] ath: phy0: Set BT/WLAN RX diversity capability
[   15.876168] ath: phy0: ASPM enabled: 0x42
[   15.876170] ath: EEPROM regdomain: 0x60
[   15.876170] ath: EEPROM indicates we should expect a direct regpair map
[   15.876172] ath: Country alpha2 being used: 00
[   15.876172] ath: Regpair used: 0x60
[   15.886565] intel_rapl: Found RAPL domain package
[   15.886567] intel_rapl: Found RAPL domain core
[   15.886568] intel_rapl: Found RAPL domain uncore
[   15.903371] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.903773] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90000ee0000, irq=17
[   15.904344] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VB: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   15.904346] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   15.904348] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   15.904349] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   15.904350] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   15.904353] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x19
[   15.904355] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x18
[   15.920260] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[   15.920343] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[   15.920428] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
[   15.943344] audit: type=1400 audit(1461249959.334:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=419 comm="apparmor_parser"
[   15.943350] audit: type=1400 audit(1461249959.334:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=419 comm="apparmor_parser"
[   15.943355] audit: type=1400 audit(1461249959.334:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=419 comm="apparmor_parser"
[   15.943562] audit: type=1400 audit(1461249959.334:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=404 comm="apparmor_parser"
[   15.943569] audit: type=1400 audit(1461249959.334:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=404 comm="apparmor_parser"
[   15.943573] audit: type=1400 audit(1461249959.334:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=404 comm="apparmor_parser"
[   15.943801] audit: type=1400 audit(1461249959.334:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=419 comm="apparmor_parser"
[   15.943807] audit: type=1400 audit(1461249959.334:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=419 comm="apparmor_parser"
[   15.943998] audit: type=1400 audit(1461249959.334:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=419 comm="apparmor_parser"
[   15.944089] audit: type=1400 audit(1461249959.334:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=404 comm="apparmor_parser"
[   15.958724] asus_wmi: ASUS WMI generic driver loaded
[   15.959985] asus_wmi: Initialization: 0x1
[   15.960153] asus_wmi: SFUN value: 0x1a0af7
[   15.960723] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input19
[   15.961024] asus_wmi: Number of fans: 0
[   16.077697] cfg80211: World regulatory domain updated:
[   16.077698] cfg80211:  DFS Master region: unset
[   16.077698] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   16.077701] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   16.077702] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   16.077702] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[   16.077703] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   16.077704] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   16.216228] usbcore: registered new interface driver ath3k
[   16.418176] usb 3-1.1: USB disconnect, device number 3
[   16.437148] media: Linux media interface: v0.10
[   16.439613] input: Logitech Gamepad F310 as /devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb1/1-1/1-1:1.0/input/input20
[   16.439687] usbcore: registered new interface driver xpad
[   16.443415] Linux video capture interface: v2.00
[   16.453150] uvcvideo: Found UVC 1.00 device ASUS USB2.0 WebCam (058f:a014)
[   16.457948] input: ASUS USB2.0 WebCam as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.0/input/input21
[   16.458028] usbcore: registered new interface driver uvcvideo
[   16.458028] USB Video Class driver (1.1.1)
[   16.529769] Console: switching to colour frame buffer device 170x48
[   16.533111] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   16.533112] i915 0000:00:02.0: registered panic notifier
[   16.872128] usb 3-1.1: new full-speed USB device number 6 using ehci-pci
[   16.965190] usb 3-1.1: New USB device found, idVendor=0cf3, idProduct=3005
[   16.965200] usb 3-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   17.536243] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
[   18.180538] init: failsafe main process (655) killed by TERM signal
[   18.560908] Bluetooth: RFCOMM TTY layer initialized
[   18.560915] Bluetooth: RFCOMM socket layer initialized
[   18.560920] Bluetooth: RFCOMM ver 1.11
[   18.863430] init: cups main process (736) killed by HUP signal
[   18.863439] init: cups main process ended, respawning
[   18.959428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   18.959431] Bluetooth: BNEP filters: protocol multicast
[   18.959435] Bluetooth: BNEP socket layer initialized
[   19.948344] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   20.202812] r8169 0000:05:00.0 eth0: link down
[   20.202825] r8169 0000:05:00.0 eth0: link down
[   20.202862] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.165138] wlan0: authenticate with 14:b9:68:80:40:d4
[   22.184905] wlan0: send auth to 14:b9:68:80:40:d4 (try 1/3)
[   22.186742] wlan0: authenticated
[   22.188667] wlan0: associate with 14:b9:68:80:40:d4 (try 1/3)
[   22.192467] wlan0: RX AssocResp from 14:b9:68:80:40:d4 (capab=0x431 status=0 aid=1)
[   22.192576] wlan0: associated
[   22.192586] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   22.194394] ath: EEPROM regdomain: 0x8318
[   22.194398] ath: EEPROM indicates we should expect a country code
[   22.194399] ath: doing EEPROM country->regdmn map search
[   22.194400] ath: country maps to regdmn code: 0x36
[   22.194401] ath: Country alpha2 being used: TR
[   22.194402] ath: Regpair used: 0x36
[   22.194403] ath: regdomain 0x8318 dynamically updated by country IE
[   22.194430] cfg80211: Regulatory domain changed to country: TR
[   22.194431] cfg80211:  DFS Master region: unset
[   22.194432] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   22.194434] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   22.194435] cfg80211:   (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   22.194437] cfg80211:   (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 2000 mBm), (0 s)
[   22.194438] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   22.335898] r8169 0000:05:00.0 eth0: link up
[   22.335921] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   22.616459] wlan0: deauthenticating from 14:b9:68:80:40:d4 by local choice (Reason: 2=PREV_AUTH_NOT_VALID)
[   22.624361] wlan0: authenticate with 14:b9:68:80:40:d4
[   22.637875] wlan0: send auth to 14:b9:68:80:40:d4 (try 1/3)
[   22.637999] cfg80211: World regulatory domain updated:
[   22.638001] cfg80211:  DFS Master region: unset
[   22.638003] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   22.638005] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   22.638006] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   22.638008] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[   22.638009] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   22.638011] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   22.639577] wlan0: authenticated
[   22.640995] wlan0: associate with 14:b9:68:80:40:d4 (try 1/3)
[   22.644696] wlan0: RX AssocResp from 14:b9:68:80:40:d4 (capab=0x431 status=0 aid=1)
[   22.644803] wlan0: associated
[   22.646455] ath: EEPROM regdomain: 0x8318
[   22.646458] ath: EEPROM indicates we should expect a country code
[   22.646460] ath: doing EEPROM country->regdmn map search
[   22.646461] ath: country maps to regdmn code: 0x36
[   22.646462] ath: Country alpha2 being used: TR
[   22.646463] ath: Regpair used: 0x36
[   22.646464] ath: regdomain 0x8318 dynamically updated by country IE
[   22.646491] cfg80211: Regulatory domain changed to country: TR
[   22.646492] cfg80211:  DFS Master region: unset
[   22.646493] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   22.646495] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   22.646497] cfg80211:   (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   22.646498] cfg80211:   (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 2000 mBm), (0 s)
[   22.646499] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   26.988810] init: plymouth-upstart-bridge main process ended, respawning
[   27.001385] init: plymouth-upstart-bridge main process ended, respawning
[   27.082162] bbswitch: module verification failed: signature and/or required key missing - tainting kernel
[   27.082403] bbswitch: version 0.7
[   27.082408] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
[   27.082411] bbswitch: Found discrete VGA device 0000:01:00.0: \_SB_.PCI0.PEGR.GFX0
[   27.082420] ACPI Warning: \_SB_.PCI0.PEGR.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150619/nsarguments-95)
[   27.082499] bbswitch: detected an Optimus _DSM function
[   27.082509] pci 0000:01:00.0: enabling device (0000 -> 0003)
[   27.082543] bbswitch: Succesfully loaded. Discrete card 0000:01:00.0 is on
[   27.084335] bbswitch: disabling discrete graphics
[   27.084346] ACPI Warning: \_SB_.PCI0.PEGR.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150619/nsarguments-95)
[   48.692417] audit_printk_skb: 168 callbacks suppressed
[   48.692420] audit: type=1400 audit(1461249992.051:68): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2242 comm="apparmor_parser"
[   48.692426] audit: type=1400 audit(1461249992.051:69): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2242 comm="apparmor_parser"
[   48.692760] audit: type=1400 audit(1461249992.051:70): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2242 comm="apparmor_parser"

heartsmagic

İki yerde bekliyor gibi, biri takas alanı eklerken.

sudo fdisk -l
sudo blkid


çıktılarını ve

gedit /etc/fstab

dosyasını bir görelim.

Diğer bekleme yeri de yazıcı ile ilgili gibi. Makineye bağlı bir yazıcı var mı?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?


Böylece yalan, dünyanın düzenine dönüştürülüyor.

FevziOztas

Yok hocam yazıcı hiç bağlı olmadı laptop açılırken.Yazıcı başka oda da ,işim olunca oraya götürüyorum pc yi genelde bu şekilde kullanırım.Swap alanını felan ayarlarken ubuntu wiki deki anlatımlara göre kurmuştum.Geçenlerde grub arayüzünü değiştirmişimtim win7 i yukarı aldım ama onun etkisi olmamıştır herhalde :D
Disk /dev/sda: 750.2 GB, 750156374016 bytes
255 heads, 63 sectors/track, 91201 cylinders, toplam 1465149168 sektör
Units = sektör of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk kimlikleyicisi: 0xb4862712

   Aygıt Açılış    Başlangıç     Bitiş  BlokSayısı Kml Sistem
/dev/sda1            2048    52430847    26214400   1c  Gizli W95 FAT32 (LBA)
/dev/sda2   *    52430848   638488575   293028864    7  HPFS/NTFS/exFAT
/dev/sda3       638488576  1403705343   382608384    7  HPFS/NTFS/exFAT
/dev/sda4      1403707390  1465147391    30720001    5  Ek
Partition 4 does not start on physical sector boundary.
/dev/sda5      1403707392  1442766847    19529728   83  Linux
/dev/sda6      1442768896  1465147391    11189248   82  Linux takas / Solaris

Disk /dev/mmcblk0: 16.0 GB, 16013852672 bytes
4 heads, 16 sectors/track, 488704 cylinders, toplam 31277056 sektör
Units = sektör of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk kimlikleyicisi: 0x00000000

/dev/mmcblk0 diski geçerli bir disk bölümleme tablosu içermiyor

/dev/sda1: LABEL="RECOVERY" UUID="14C5-F177" TYPE="vfat"
/dev/sda2: LABEL="OS" UUID="FA3C8DB33C8D6C07" TYPE="ntfs"
/dev/sda3: UUID="623A36E83A36B93D" TYPE="ntfs"
/dev/sda5: UUID="823f1b11-6f63-47bd-a4c6-55cc9328ee9e" TYPE="ext4"
/dev/sda6: UUID="a29a9804-3ff1-42c3-b653-e0e30d4d905c" TYPE="swap"

# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
# / was on /dev/sda5 during installation
UUID=823f1b11-6f63-47bd-a4c6-55cc9328ee9e /               ext4    errors=remount-ro 0       1
# swap was on /dev/sda6 during installation
UUID=a29a9804-3ff1-42c3-b653-e0e30d4d905c none            swap    sw              0       0