Asus N14 Wireless N300 Driver Güncelleme sorunu (Manjaro Linux)

[casberg]

Kablosuz ağımda çalışma problemi yok ama normalde eth0-1-2-3 ve wlan0-1-2-3 vs... diye görünmesi gereken sürücüm ;

Kod Seç Genişlet

[jeeves@GB ~]$ ifconfig
enp3s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 10.42.0.1  netmask 255.255.255.0  broadcast 10.42.0.255
        inet6 fe80::6ef0:49ff:fe00:d08d  prefixlen 64  scopeid 0x20<link>
        ether 6c:f0:49:00:d0:8d  txqueuelen 1000  (Ethernet)
        RX packets 138745  bytes 16194592 (15.4 MiB)
        RX errors 0  dropped 31  overruns 0  frame 0
        TX packets 175708  bytes 211695627 (201.8 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 30708  bytes 2536144 (2.4 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 30708  bytes 2536144 (2.4 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp0s19f2u6mon: flags=67<UP,BROADCAST,RUNNING>  mtu 1500
        inet 192.168.2.4  netmask 255.255.255.0  broadcast 192.168.2.255
        inet6 fe80::3a2c:4aff:fe4f:1cd6  prefixlen 64  scopeid 0x20<link>
        ether 38:2c:4a:4f:1c:d6  txqueuelen 1000  (Ethernet)
        RX packets 129328  bytes 118085150 (112.6 MiB)
        RX errors 0  dropped 1255  overruns 0  frame 0
        TX packets 71814  bytes 11782485 (11.2 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0


enp3s0 ve wlp0s19f2u6mon şeklinde görünüyor. Sürücümün ticari sürümünü yükleyim belki düzelir dedim ama gerek yok derseniz bunu düzeltmek için bana fikir verebilirmisiniz? Neyse ;

Şu linkten https://www.asus.com/tr/Networking/USBN14/HelpDesk_Download/
DR_USB_N14_261320140102_Linux.zip doyasını indirdim ve bir yerde tarif buldum sonra dosyaları klasöre çaıkardım içindeki README_STA_usb dosyasına baktım ;

Kod Seç Genişlet

* README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

=======================================================================
ModelName:
===========
RT2870 Wireless Lan Linux Driver


=======================================================================
Driver lName:
===========
rt2870.o/rt2870.ko


=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.


=======================================================================
Ralink Hardware:
===================
Ralink 802.11n Wireless LAN Card.


=======================================================================
Description:
=============
This is a linux device driver for Ralink RT2870 USB ABGN WLAN Card.


=======================================================================
Contents:
=============
Makefile         : Makefile
*.c : c files
*.h : header files


=======================================================================
Features:
==========
   This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
   open or shared or WPA-PSK or WPA2-PSK authentication method.
   NONE, WEP, TKIP and AES encryption.


=======================================================================
Build Instructions: 
====================

1> $tar -xvzf DPB_RT2870_Linux_STA_x.x.x.x.tgz
    go to "./DPB_RT2870_Linux_STA_x.x.x.x" directory.
   
2> In Makefile
set the "MODE = STA" in Makefile and chose the TARGET to Linux by set "TARGET = LINUX"
define the linux kernel source include file path LINUX_SRC
modify to meet your need.

3> In os/linux/config.mk
define the GCC and LD of the target machine
define the compiler flags CFLAGS
modify to meet your need.
** Build for being controlled by NetworkManager or wpa_supplicant wext functions
   Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y'.
   => #>cd wpa_supplicant-x.x
   => #>./wpa_supplicant -Dwext -ira0 -c wpa_supplicant.conf -d
** Build for being controlled by WpaSupplicant with Ralink Driver
   Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n'.
   => #>cd wpa_supplicant-0.5.7
   => #>./wpa_supplicant -Dralink -ira0 -c wpa_supplicant.conf -d

4> $make
# compile driver source code
# To fix "error: too few arguments to function ¡¥iwe_stream_add_event"
  => $patch -i os/linux/sta_ioctl.c.patch os/linux/sta_ioctl.c

5> $cp RT2870STA.dat  /etc/Wireless/RT2870STA/RT2870STA.dat
   
6> load driver, go to "os/linux/" directory.
    #[kernel 2.4]
    #    $/sbin/insmod rt5572sta.o
    #    $/sbin/ifconfig ra0 inet YOUR_IP up
       
    #[kernel 2.6]
    #    $/sbin/insmod rt5572sta.ko
    #    $/sbin/ifconfig ra0 inet YOUR_IP up

7> unload driver   
    $/sbin/ifconfig ra0 down
$/sbin/rmmod rt5572sta

=======================================================================
CONFIGURATION: 
====================
RT2870 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file

i)  iwconfig comes with kernel. 
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)modify configuration file "RT2870STA.dat" in /etc/Wireless/RT2870STA/RT2870STA.dat.
           
Configuration File : RT2870STA.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT2870STA/RT2870STA.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi RT2870STA.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
SSID=Dennis2860AP
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=OPEN
EncrypType=NONE
WPAPSK=
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
EthConvertMode=
EthCloneMac=
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
MeshId=MESH
MeshAutoLink=1
MeshAuthMode=OPEN
MeshEncrypType=NONE
MeshWPAKEY=
MeshDefaultkey=1
MeshWEPKEY=
CarrierDetect=0

-----------------------------------------------
*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)

All WMM parameters do not support iwpriv command but ¡¥WmmCapable¡¦¡¦,
please store all parameter to RT2870STA.dat, and restart driver.

-----------------------------------------------
syntax is 'Param'='Value' and describes below.

@> CountryRegion=value                                 
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10 ~ 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
   31: use 1 ~ 14 Channel (ch1-11:active scan, ch12-14 passive scan)
                                         
@> CountryRegionABand=value     
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: use 52, 56, 60, 64 Channel
9: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 Channel
   10: use 36, 40, 44, 48, 149, 153, 157, 161, 165 Channel
   11: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 Channel

@> CountryCode=value
value
AG, AR, AW, AU, AT, BS, BB, BM, BR, BE, BG, CA, KY, CL, CN, CO, CR, CY, CZ, DK, DO, EC, SV, FI, FR, DE,
GR, GU, GT, HT, HN, HK, HU, IS, IN, ID, IE, IL, IT, JP, JO, LV, LI, LT, LU, MY, MT, MA, MX, NL, NZ, NO,
PE, PT, PL, RO, RU, SA, CS, SG, SK, SI, ZA, KR, ES, SE, CH, TW, TR, GB, UA, AE, US, VE
"" => using default setting: 2.4 G - ch 1~11; 5G - ch 52~64, 100~140, 149~165
                                                           
@> SSID=value               
value
0~z, 1~32 ascii characters.
                   
@> WirelessMode=value
value
0: legacy 11b/g mixed
1: legacy 11B only
2: legacy 11A only         //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
3: legacy 11a/b/g mixed     //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
4: legacy 11G only
5: 11ABGN mixed
6: 11N only
7: 11GN mixed
8: 11AN mixed
9: 11BGN mixed
   10: 11AGN mixed
                     
@> Channel=value
value
depends on CountryRegion or CountryRegionABand
                   
@> BGProtection=value
value
0: Auto
1: Always on
2: Always off
                   
@> TxPreamble=value
  value
0:Preamble Long
1:Preamble Short
2:Auto
                   
@> RTSThreshold=value
value
1~2347                                                       
                                                           
@> FragThreshold=value
value       
256~2346
                   
@> TxBurst=value
value
0: Disable
1: Enable

@> NetworkType=value    
value
Infra: infrastructure mode
        Adhoc: adhoc mode
                                                                                                                                                                                                                 
@> AuthMode=value
value
OPEN For open system
SHARED   For shared key system
WEPAUTO     Auto switch between OPEN and SHARED
WPAPSK      For WPA pre-shared key  (Infra)
WPA2PSK     For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key  (Adhoc)
WPA         Use WPA-Supplicant
WPA2        Use WPA-Supplicant

@> EncrypType=value
value
NONE For AuthMode=OPEN                   
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK                   
AES For AuthMode=WPAPSK or WPA2PSK                     

@> DefaultKeyID=value
value
1~4

@> Key1=value
    Key2=value
    Key3=value
    Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd
    (usage : "iwpriv" only)     

@> Key1Type=vaule
    Key2Type=value
    Key3Type=vaule
    Key4Type=vaule
    value
0   hexadecimal type
1   assic type
    (usage : reading profile only)

@> Key1Str=value
    Key2Str=value
    Key3Str=vaule
    Key4Str=vaule
    value
10 or 26 characters (key type=0)
5 or 13 characters  (key type=1)
    (usage : reading profile only)

@> WPAPSK=value             
value
8~63 ASCII  or
64 HEX characters
                   
@> WmmCapable=value
value
0: Disable WMM
1: Enable WMM
       
@> PSMode=value
    value
    CAM     Constantly Awake Mode
Max_PSP     Max Power Savings
Fast_PSP Power Save Mode

@> FastRoaming=value
value
0 Disabled
1 Enabled

@> RoamThreshold=value
value
Positive Interger(dBm)

@> HT_RDG=value
value
0 Disabled
1 Enabled

@> HT_EXTCHA=value (Extended Channel Switch Announcement)
value
0 Below
1 Above

@> HT_OpMode=value
value
0 HT mixed format
1 HT greenfield format

@> HT_MpduDensity=value
value (based on 802.11n D2.0)
0: no restriction
1: 1/4 £gs
2: 1/2 £gs
3: 1 £gs
4: 2 £gs
5: 4 £gs
6: 8 £gs
7: 16 £gs

@> HT_BW=value
value
0 20MHz
1 40MHz

@> HT_AutoBA=value
value
0 Disabled
1 Enabled

@> HT_BADecline
value
0 Disabled
1     Enabled <Reject BA request from AP>

@> HT_AMSDU=value
value
0 Disabled
1 Enabled

@> HT_BAWinSize=value
value
1 ~ 64

@> HT_GI=value
value
0 long GI
1 short GI

@> HT_MCS=value
value
0 ~ 15
33: auto

@> HT_MIMOPSMode=value
value (based on 802.11n D2.0)
0 Static SM Power Save Mode
1 Dynamic SM Power Save Mode
2 Reserved
3 SM enabled
(not fully support yet)

@> EthConvertMode=value
value
dongle
clone
hybrid

@> EthCloneMac=value
value
xx:xx:xx:xx:xx:xx

@> IEEE80211H=value
value
0 Disabled
1 Enabled

@> TGnWifiTest=value
value
0 Disabled
1 Enabled

@> WirelessEvent=value
value
0 Disabled
1 Enabled <send custom wireless event>
   
@> MeshId=value
value
Length 1~32 ascii characters

@> MeshAutoLink=value
value
0 Disabled
1 Enabled

@> MeshAuthMode=value
value
OPEN For open system
WPANONE For WPA pre-shared key  (Adhoc)

@> MeshEncrypType=value
value
NONE For MeshAuthMode=OPEN                   
WEP For MeshAuthMode=OPEN
TKIP For MeshAuthMode=WPANONE
AES For MeshAuthMode=WPANONE

@> MeshWPAKEY=value
value
8~63 ASCII  or
64 HEX characters

@> MeshDefaultkey=value
value
1~4

@> MeshWEPKEY=value
value
10 or 26 characters
5 or 13 characters

@> CarrierDetect=value
value
0 Disabled
1 Enabled

MORE INFORMATION
=================================================================================
If you want for rt2870 driver to auto-load at boot time:
A) choose ra0 for first RT2870 WLAN card, ra1 for second RT2870 WLAN card, etc.
   
B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,     
   edit( or add the line) in /etc/modules.conf:
       alias ra0 rt2870sta
   
C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0 
   DEVICE='ra0'
   ONBOOT='yes'     


NOTE:
   if you use dhcp, add this line too .
    BOOTPROTO='dhcp'

*D) To ease the Default Gateway setting,
    add the line
    GATEWAY=x.x.x.x   
    in /etc/sysconfig/network
   
=======================================================================
Dongle/Clone Features:
======================
A) Dongle mode:
    Provides a 1-to-N MAC address mapping mechanism such that more than one PC behind the STA
    can transparently connect to the AP.

B) Clone mode:
Provides a 1-to-1 MAC address mapping mechanism.
STA can use own MAC as SA MAC or
use user desired MAC as SA MAC or
    use source MAC of first packet coming from wired device as SA MAC.
NOTE: In this mode, only the PC who own the specified MAC can connect to the AP.


C) Hybrid mode(Dongle+Clone):
Provides a 1-to-N MAC address mapping mechanism such that more than one PC behind the STA
    can transparently connect to the AP.
STA can use own MAC as SA MAC or
use user desired MAC as SA MAC or
    use source MAC of first packet coming from wired device as SA MAC.

D) Please refer to "Config STA to link as dongle mode..." in iwpriv_usage.txt for releated commands.

Yazanları anlamaya çalıştım ama bişey anlamadım sadece yukarıdaki kurulum şıklarından 2'ncisinde ;

Kod Seç Genişlet

2> In Makefile
set the "MODE = STA" in Makefile and chose the TARGET to Linux by set "TARGET = LINUX"
define the linux kernel source include file path LINUX_SRC
modify to meet your need.
Benden istediği linux kernelin hangisi olduğunu bilemedim. Benim ayar yöneticisinde birkaç tane kernel listelemiş doğru yere mi baktım? Doğru baktıysam sitenin benden istediği kernel çok eski. Yanlış baktıysam ne yapmam gerekiyor acaba?

Benim sistemdeki kernel'ların listesi bunlar ;

[heartsmagic]

İsimlendirmede bir sorun yok. Bu isimler systemd ile beraber bu şekilde olacak artık. Şuraya bakabilirsin:
https://github.com/systemd/systemd/blob/master/src/udev/udev-builtin-net_id.c#L20