[Çözüldü] Harici Ethernet kartı sistem açıldığında çalışmıyor

[CeeMoo]

İyi Günler
- Her şey iyi gidiyordu birden nasıl oldu bilmiyorum ama böyle bir sorun ile karşılaştım.Kısacası anakartımın internet girişi bozuldu bende harici aldım.Ubuntuda harici kart çalışıyordu.Ama ne yaptığımı bilmiyorum.Şuan sistem açılışında int kartı çalışıyor sisteme(ubuntu) giriş yapılınca ışıklar birden sönüyor.(Başka dağıtımda denedim aynı sorun ordada devam etti.)Terminalden biraz bilgi aldım şöyle:

04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)

ifconfig -a

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr c8:3a:35:d5:6c:f7 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:19 Base address:0xe000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:336 errors:0 dropped:0 overruns:0 frame:0
          TX packets:336 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:26592 (26.5 KB)  TX bytes:26592 (26.5 KB)

sudo lshw -C network

Kod Seç Genişlet

  *-network               
       description: Ethernet interface
       product: RTL-8169 Gigabit Ethernet
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 1
       bus info: pci@0000:04:01.0
       logical name: eth0
       version: 10
       serial: c8:3a:35:d5:6c:f7
       size: 10Mbit/s
       capacity: 1Gbit/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s
       resources: irq:19 ioport:de00(size=256) memory:fdbff000-fdbff0ff memory:fda00000-fda1ffff

iwlist scanning

Kod Seç Genişlet

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

Windowsda belli bir taramadan sonra çalışıyor ama Linux bir yerde tıkanıyor biraz araştırdım ama malesef sonuca ulaşamadım.

[heartsmagic]

Harici kart ne üzerinden çalışıyor? PCI mı? Çıktısını verdiğin kart harici kartsa dahili kart neden görünmüyor?

[CeeMoo]

Harici kart ne üzerinden çalışıyor? PCI mı? Çıktısını verdiğin kart harici kartsa dahili kart neden görünmüyor?

PCI takılı evet.

Anakartın sahip olduğu int : AR8131 chip (10/100/1000 Mbit) - Atheros AR8131/AR8132
Harici Ethernet ağ ayarlarında isim : Realtek RTL8169/8110 Ailesi PCI Gigabit Ethernet NIC (NDIS 6.20)
Harici Ethernet AIDA64 gözüken :    Realtek RTL8169/8110 Gigabit Ethernet Adapter

Aslında PCI ethernet kartı sisteme girişte çalışmayı bırakıyor.Anakartımın kendi lan'ı ise binaya şimşek deymesi üzerine akımdan gitti.

Manuel olarak ip adresi girdim gene çalışmadı.Daha sonra Realtek ALC887 Linux kurulumunu buldum denedim ama onu beceremedim bir yerde hep hata veriyor.Belki sistemi bozmuşumdur diye başka dağıtım kullandım oda olmad

[heartsmagic]

Harici kart görünüyor o zaman söylediğin gibi, dahili kart piyasada hiç yok. Fakat neden IP almıyor bilemiyorum. Sürücüye falan gerek yok zira sistem görüyor kartı. Modül olarak da ilgili modülü kullanıyor görünmekte: r8169 yani. Dahili kartı BIOS tarafından kapatman mümkün mü, var mı böyle bir seçenek?

Elle IP aldığında neler oldu peki? Tam olarak neler yaptın? IP ataması, route eklenmesi sonrasında modeme falan ping isteği yapınca cevap alamadın mı?
ifconfig çıktısı nasıldı elle IP verdikten sonra?

[CeeMoo]

Harici kart görünüyor o zaman söylediğin gibi, dahili kart piyasada hiç yok. Fakat neden IP almıyor bilemiyorum. Sürücüye falan gerek yok zira sistem görüyor kartı. Modül olarak da ilgili modülü kullanıyor görünmekte: r8169 yani. Dahili kartı BIOS tarafından kapatman mümkün mü, var mı böyle bir seçenek?

Elle IP aldığında neler oldu peki? Tam olarak neler yaptın? IP ataması, route eklenmesi sonrasında modeme falan ping isteği yapınca cevap alamadın mı?
ifconfig çıktısı nasıldı elle IP verdikten sonra?

Her şey birden oldu.Ama görmesi beni mutlu etti.Demek biraz kurcalasam ulaşabilirim.

- Elle ip atadım ama gene bir etki vb.. olmadı.Bir ara ışık yanmıştı.O zaman biraz daha kurcalayayım bir şeylere ulaşır isem konuda bilgilendiririm.

İlginiz alakanız için Teşekkürler.

[if]

https://forum.ubuntu-tr.net/index.php?topic=28764.0

[CeeMoo]

https://forum.ubuntu-tr.net/index.php?topic=28764.0

Şöyle yazayım.
  -Mint yükledim denedim.
  - İp adresi manuel ettim ve sonuçlar gene aynı.

cat /etc/lsb-release

Kod Seç Genişlet

DISTRIB_ID=LinuxMint
DISTRIB_RELEASE=17.1
DISTRIB_CODENAME=rebecca
DISTRIB_DESCRIPTION="Linux Mint 17.1 Rebecca"

uname -a

Kod Seç Genişlet

Linux cee-G31M-ES2L 3.13.0-37-generic #64-Ubuntu SMP Mon Sep 22 21:28:38 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux

lspci

Kod Seç Genişlet

00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 01)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01)
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01)
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV730 PRO [Radeon HD 4650]
01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] RV710/730 HDMI Audio [Radeon HD 4000 series]
04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8169 PCI Gigabit Ethernet Controller (rev 10)

lsusb

Kod Seç Genişlet

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 046d:c248 Logitech, Inc.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 275d:0a29 
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

rfkill list 
- bir şey vermedi

lsusb

Kod Seç Genişlet

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 046d:c248 Logitech, Inc.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 275d:0a29 
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

sudo lshw -C network

Kod Seç Genişlet

  *-network               
       description: Ethernet interface
       product: RTL8169 PCI Gigabit Ethernet Controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 1
       bus info: pci@0000:04:01.0
       logical name: eth0
       version: 10
       serial: c8:3a:35:d5:6c:f7
       size: 10Mbit/s
       capacity: 1Gbit/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s
       resources: irq:19 ioport:de00(size=256) memory:fdbff000-fdbff0ff memory:fda00000-fda1ffff

ifconfig

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr c8:3a:35:d5:6c:f7 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:147 errors:0 dropped:0 overruns:0 frame:0
          TX packets:147 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:10545 (10.5 KB)  TX bytes:10545 (10.5 KB)

iwconfig

Kod Seç Genişlet

eth0      no wireless extensions.

lo        no wireless extensions.


iwlist scanning

Kod Seç Genişlet

eth0      Interface doesn't support scanning.

lo        Interface doesn't support scanning.

lsmod

Kod Seç Genişlet

Module                  Size  Used by
bnep                   19624  2
rfcomm                 69160  0
bluetooth             391136  10 bnep,rfcomm
binfmt_misc            17468  1
gpio_ich               13476  0
snd_hda_codec_hdmi     46368  1
coretemp               13435  0
kvm_intel             143109  0
kvm                   451552  1 kvm_intel
snd_hda_codec_realtek    65580  1
snd_seq_midi           13324  0
snd_seq_midi_event     14899  1 snd_seq_midi
serio_raw              13462  0
lpc_ich                21080  0
dm_multipath           22873  0
scsi_dh                14882  1 dm_multipath
snd_rawmidi            30144  1 snd_seq_midi
snd_hda_intel          56451  5
snd_hda_codec         192906  3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_hwdep              13602  1 snd_hda_codec
snd_seq                61560  2 snd_seq_midi_event,snd_seq_midi
snd_pcm               102099  3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_seq_device         14497  3 snd_seq,snd_rawmidi,snd_seq_midi
snd_page_alloc         18710  2 snd_pcm,snd_hda_intel
snd_timer              29482  2 snd_pcm,snd_seq
snd                    69322  21 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
parport_pc             32701  1
soundcore              12680  1 snd
ppdev                  17671  0
mac_hid                13205  0
lp                     17759  0
parport                42348  3 lp,ppdev,parport_pc
dm_mirror              22135  0
dm_region_hash         20862  1 dm_mirror
dm_log                 18411  2 dm_region_hash,dm_mirror
hid_generic            12548  0
usbhid                 52659  0
hid                   106148  2 hid_generic,usbhid
radeon               1522526  3
psmouse               106678  0
r8169                  67581  0
mii                    13934  1 r8169
floppy                 69418  0
i2c_algo_bit           13413  1 radeon
ttm                    85150  1 radeon
drm_kms_helper         55071  1 radeon
drm                   303102  5 ttm,drm_kms_helper,radeon

dmesg

Kod Seç Genişlet

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.13.0-37-generic (buildd@kapok) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #64-Ubuntu SMP Mon Sep 22 21:28:38 UTC 2014 (Ubuntu 3.13.0-37.64-generic 3.13.11.7)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-37-generic root=UUID=11ccce5c-5a27-4ee6-8b31-2e45db6ffd14 ro quiet splash vt.handoff=7
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007fedffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007fee0000-0x000000007fee2fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007fee3000-0x000000007feeffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007fef0000-0x000000007fefffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.4 present.
[    0.000000] DMI: Gigabyte Technology Co., Ltd. G31M-ES2L/G31M-ES2L, BIOS FH 04/30/2010
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x7fee0 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-through
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 07FF00000 mask FFFF00000 uncachable
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[    0.000000] total RAM covered: 2047M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K chunk_size: 2M num_reg: 2  lose cover RAM: 0G
[    0.000000] New variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[    0.000000] found SMP MP-table at [mem 0x000f53c0-0x000f53cf] mapped at [ffff8800000f53c0]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE
[    0.000000] BRK [0x01fe2000, 0x01fe2fff] PGTABLE
[    0.000000] BRK [0x01fe3000, 0x01fe3fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7fc00000-0x7fdfffff]
[    0.000000]  [mem 0x7fc00000-0x7fdfffff] page 2M
[    0.000000] BRK [0x01fe4000, 0x01fe4fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7c000000-0x7fbfffff]
[    0.000000]  [mem 0x7c000000-0x7fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x7bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x7fe00000-0x7fedffff]
[    0.000000]  [mem 0x7fe00000-0x7fedffff] page 4k
[    0.000000] BRK [0x01fe5000, 0x01fe5fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x348b2000-0x36450fff]
[    0.000000] ACPI: RSDP 00000000000f6db0 000014 (v00 GBT   )
[    0.000000] ACPI: RSDT 000000007fee3040 00003C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: FACP 000000007fee30c0 000074 (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: DSDT 000000007fee3180 0040E8 (v01 GBT    GBTUACPI 00001000 MSFT 0100000C)
[    0.000000] ACPI: FACS 000000007fee0000 000040
[    0.000000] ACPI: HPET 000000007fee73c0 000038 (v01 GBT    GBTUACPI 42302E31 GBTU 00000098)
[    0.000000] ACPI: MCFG 000000007fee7440 00003C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: TAMG 000000007fee7480 00625A (v01 GBT    GBT   B0 5455312E BG?? 00020101)
[    0.000000] ACPI: APIC 000000007fee72c0 000084 (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: SSDT 000000007feedd40 0003AB (v01  PmRef    CpuPm 00003000 INTL 20040311)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000007fedffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x7fedffff]
[    0.000000]   NODE_DATA [mem 0x7fedb000-0x7fedffff]
[    0.000000]  [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0x7fedffff]
[    0.000000] On node 0 totalpages: 523902
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 8124 pages used for memmap
[    0.000000]   DMA32 zone: 519904 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] e820: [mem 0x7ff00000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 29 pages/cpu @ffff88007fc00000 s86400 r8192 d24192 u524288
[    0.000000] pcpu-alloc: s86400 r8192 d24192 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 515693
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-37-generic root=UUID=11ccce5c-5a27-4ee6-8b31-2e45db6ffd14 ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 2017452K/2095608K available (7375K kernel code, 1144K rwdata, 3404K rodata, 1336K init, 1444K bss, 78156K reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000] Offload RCU callbacks from all CPUs
[    0.000000] Offload RCU callbacks from CPUs: 0-3.
[    0.000000] NR_IRQS:16640 nr_irqs:712 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 8388608 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2933.605 MHz processor
[    0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5867.21 BogoMIPS (lpj=11734420)
[    0.004007] pid_max: default: 32768 minimum: 301
[    0.004042] Security Framework initialized
[    0.004069] AppArmor: AppArmor initialized
[    0.004070] Yama: becoming mindful.
[    0.004252] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.008757] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.009275] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.009279] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.009525] Initializing cgroup subsys memory
[    0.009533] Initializing cgroup subsys devices
[    0.009535] Initializing cgroup subsys freezer
[    0.009537] Initializing cgroup subsys blkio
[    0.009539] Initializing cgroup subsys perf_event
[    0.009541] Initializing cgroup subsys hugetlb
[    0.009565] CPU: Physical Processor ID: 0
[    0.009567] CPU: Processor Core ID: 0
[    0.009568] mce: CPU supports 6 MCE banks
[    0.009575] CPU0: Thermal monitoring enabled (TM2)
[    0.009583] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[    0.009583] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
[    0.009583] tlb_flushall_shift: -1
[    0.009679] Freeing SMP alternatives memory: 32K (ffffffff81e6e000 - ffffffff81e76000)
[    0.011003] ACPI: Core revision 20131115
[    0.012280] ACPI: All ACPI Tables successfully acquired
[    0.013428] ftrace: allocating 28541 entries in 112 pages
[    0.020456] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.061686] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU     E7500  @ 2.93GHz (fam: 06, model: 17, stepping: 0a)
[    0.064000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[    0.064000] ... version:                2
[    0.064000] ... bit width:              40
[    0.064000] ... generic registers:      2
[    0.064000] ... value mask:             000000ffffffffff
[    0.064000] ... max period:             000000007fffffff
[    0.064000] ... fixed-purpose events:   3
[    0.064000] ... event mask:             0000000700000003
[    0.064000] x86: Booting SMP configuration:
[    0.064000] .... node  #0, CPUs:      #1
[    0.074883] x86: Booted up 1 node, 2 CPUs
[    0.074886] smpboot: Total of 2 processors activated (11734.42 BogoMIPS)
[    0.074987] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.076125] devtmpfs: initialized
[    0.076196] EVM: security.selinux
[    0.076198] EVM: security.SMACK64
[    0.076199] EVM: security.ima
[    0.076200] EVM: security.capability
[    0.076219] PM: Registering ACPI NVS region [mem 0x7fee0000-0x7fee2fff] (12288 bytes)
[    0.076891] pinctrl core: initialized pinctrl subsystem
[    0.076957] regulator-dummy: no parameters
[    0.076983] RTC time: 13:37:42, date: 06/07/15
[    0.077021] NET: Registered protocol family 16
[    0.077125] cpuidle: using governor ladder
[    0.077126] cpuidle: using governor menu
[    0.077155] ACPI: bus type PCI registered
[    0.077157] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.077209] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.077212] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.089372] PCI: Using configuration type 1 for base access
[    0.092050] bio: create slab <bio-0> at 0
[    0.092070] ACPI: Added _OSI(Module Device)
[    0.092072] ACPI: Added _OSI(Processor Device)
[    0.092073] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.092075] ACPI: Added _OSI(Processor Aggregator Device)
[    0.093453] ACPI BIOS Warning (bug): Incorrect checksum in table [TAMG] - 0xD1, should be 0xD0 (20131115/tbprint-214)
[    0.093548] ACPI: SSDT 000000007feed720 00026C (v01  PmRef  Cpu0Ist 00003000 INTL 20040311)
[    0.093663] ACPI: Dynamic OEM Table Load:
[    0.093665] ACPI: SSDT           (null) 00026C (v01  PmRef  Cpu0Ist 00003000 INTL 20040311)
[    0.093729] ACPI: SSDT 000000007feedbe0 000152 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.093837] ACPI: Dynamic OEM Table Load:
[    0.093839] ACPI: SSDT           (null) 000152 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.093937] ACPI: Interpreter enabled
[    0.093943] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
[    0.093946] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[    0.093957] ACPI: (supports S0 S3 S4 S5)
[    0.093959] ACPI: Using IOAPIC for interrupt routing
[    0.093984] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.094059] ACPI: No dock devices found.
[    0.097390] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.097396] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.097400] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.097584] PCI host bridge to bus 0000:00
[    0.097587] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.097589] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.097590] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.097592] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.097594] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.097596] pci_bus 0000:00: root bus resource [mem 0x7ff00000-0xfebfffff]
[    0.097603] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
[    0.097681] pci 0000:00:01.0: [8086:29c1] type 01 class 0x060400
[    0.097713] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.097791] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.097805] pci 0000:00:1b.0: reg 0x10: [mem 0xfdff8000-0xfdffbfff 64bit]
[    0.097861] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.097899] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.097927] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.097984] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.098023] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.098053] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.098109] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.098149] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.098178] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.098212] pci 0000:00:1d.0: reg 0x20: [io  0xff00-0xff1f]
[    0.098260] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.098286] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.098319] pci 0000:00:1d.1: reg 0x20: [io  0xfe00-0xfe1f]
[    0.098367] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.098394] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.098427] pci 0000:00:1d.2: reg 0x20: [io  0xfd00-0xfd1f]
[    0.098475] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.098503] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.098537] pci 0000:00:1d.3: reg 0x20: [io  0xfc00-0xfc1f]
[    0.098585] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.098616] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.098630] pci 0000:00:1d.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
[    0.098723] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.098750] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.098820] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.098850] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
[    0.098919] pci 0000:00:1f.0: address space collision: [io  0x0400-0x047f] conflicts with ACPI CPU throttle [??? 0x00000410-0x00000415 flags 0x80000000]
[    0.098923] pci 0000:00:1f.0: quirk: [io  0x0480-0x04bf] claimed by ICH6 GPIO
[    0.098926] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f)
[    0.098929] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f)
[    0.099009] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x010180
[    0.099021] pci 0000:00:1f.2: reg 0x10: [io  0x0000-0x0007]
[    0.099027] pci 0000:00:1f.2: reg 0x14: [io  0x0000-0x0003]
[    0.099034] pci 0000:00:1f.2: reg 0x18: [io  0x0000-0x0007]
[    0.099041] pci 0000:00:1f.2: reg 0x1c: [io  0x0000-0x0003]
[    0.099047] pci 0000:00:1f.2: reg 0x20: [io  0xf900-0xf90f]
[    0.099076] pci 0000:00:1f.2: PME# supported from D3hot
[    0.099134] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.099179] pci 0000:00:1f.3: reg 0x20: [io  0x0500-0x051f]
[    0.099284] pci 0000:01:00.0: [1002:9498] type 00 class 0x030000
[    0.099296] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.099305] pci 0000:01:00.0: reg 0x18: [mem 0xfdce0000-0xfdceffff 64bit]
[    0.099312] pci 0000:01:00.0: reg 0x20: [io  0xae00-0xaeff]
[    0.099323] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.099349] pci 0000:01:00.0: supports D1 D2
[    0.099383] pci 0000:01:00.1: [1002:aa38] type 00 class 0x040300
[    0.099394] pci 0000:01:00.1: reg 0x10: [mem 0xfdcfc000-0xfdcfffff 64bit]
[    0.099443] pci 0000:01:00.1: supports D1 D2
[    0.099486] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.099488] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.099491] pci 0000:00:01.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.099494] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.099534] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.099538] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.099541] pci 0000:00:1c.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.099545] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.099587] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.099590] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.099593] pci 0000:00:1c.1:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.099598] pci 0000:00:1c.1:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.099631] pci 0000:04:01.0: [10ec:8169] type 00 class 0x020000
[    0.099647] pci 0000:04:01.0: reg 0x10: [io  0xde00-0xdeff]
[    0.099655] pci 0000:04:01.0: reg 0x14: [mem 0xfdbff000-0xfdbff0ff]
[    0.099692] pci 0000:04:01.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.099716] pci 0000:04:01.0: supports D1 D2
[    0.099717] pci 0000:04:01.0: PME# supported from D1 D2 D3hot
[    0.099777] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.099781] pci 0000:00:1e.0:   bridge window [io  0xd000-0xdfff]
[    0.099784] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.099788] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.099790] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.099792] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.099794] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.099796] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.099798] pci 0000:00:1e.0:   bridge window [mem 0x7ff00000-0xfebfffff] (subtractive decode)
[    0.100182] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.100228] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.100273] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.100317] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.100361] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100407] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100452] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100497] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.100572] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.100577] ACPI: \_SB_.PCI0: notify handler is installed
[    0.100599] Found 1 acpi root devices
[    0.100672] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.100672] vgaarb: loaded
[    0.100672] vgaarb: bridge control possible 0000:01:00.0
[    0.100672] SCSI subsystem initialized
[    0.100672] libata version 3.00 loaded.
[    0.100672] ACPI: bus type USB registered
[    0.100672] usbcore: registered new interface driver usbfs
[    0.100672] usbcore: registered new interface driver hub
[    0.100672] usbcore: registered new device driver usb
[    0.100672] PCI: Using ACPI for IRQ routing
[    0.108873] PCI: pci_cache_line_size set to 64 bytes
[    0.108908] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[    0.108909] e820: reserve RAM buffer [mem 0x7fee0000-0x7fffffff]
[    0.108993] NetLabel: Initializing
[    0.108995] NetLabel:  domain hash size = 128
[    0.108996] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.109010] NetLabel:  unlabeled traffic allowed by default
[    0.109020] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.109020] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.109020] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.110054] Switched to clocksource hpet
[    0.113570] AppArmor: AppArmor Filesystem Enabled
[    0.113618] pnp: PnP ACPI init
[    0.113634] ACPI: bus type PNP registered
[    0.113794] system 00:00: [io  0x04d0-0x04d1] has been reserved
[    0.113796] system 00:00: [io  0x0290-0x029f] has been reserved
[    0.113798] system 00:00: [io  0x0800-0x087f] has been reserved
[    0.113800] system 00:00: [io  0x0290-0x0294] has been reserved
[    0.113802] system 00:00: [io  0x0880-0x088f] has been reserved
[    0.113806] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.113815] pnp 00:01: [dma 4]
[    0.113830] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.113902] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.113937] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.113959] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.113983] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.114073] pnp 00:06: [dma 2]
[    0.114101] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.114259] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.114417] pnp 00:08: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.114525] system 00:09: [io  0x0400-0x04cf] could not be reserved
[    0.114528] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.114683] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.114686] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.114808] system 00:0b: [mem 0x000f0000-0x000f3fff] could not be reserved
[    0.114810] system 00:0b: [mem 0x000f4000-0x000f7fff] could not be reserved
[    0.114812] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.114814] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.114816] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved
[    0.114818] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.114820] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved
[    0.114823] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.114825] system 00:0b: [mem 0xfed13000-0xfed1dfff] has been reserved
[    0.114827] system 00:0b: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.114829] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.114831] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved
[    0.114833] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
[    0.114835] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
[    0.114837] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.114867] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[    0.114871] pnp: PnP ACPI: found 13 devices
[    0.114872] ACPI: bus type PNP unregistered
[    0.121094] pci 0000:00:1f.0: BAR 13: [io  0x0400-0x047f] has bogus alignment
[    0.121101] pci 0000:01:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref]
[    0.121103] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.121105] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.121108] pci 0000:00:01.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.121111] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.121115] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.121117] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.121121] pci 0000:00:1c.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.121124] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.121129] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.121131] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.121135] pci 0000:00:1c.1:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.121138] pci 0000:00:1c.1:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.121144] pci 0000:04:01.0: BAR 6: assigned [mem 0xfda00000-0xfda1ffff pref]
[    0.121146] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.121148] pci 0000:00:1e.0:   bridge window [io  0xd000-0xdfff]
[    0.121152] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.121155] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.121160] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.121162] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.121164] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.121166] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.121167] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff]
[    0.121169] pci_bus 0000:01: resource 0 [io  0xa000-0xafff]
[    0.121171] pci_bus 0000:01: resource 1 [mem 0xfdc00000-0xfdcfffff]
[    0.121173] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.121175] pci_bus 0000:02: resource 0 [io  0xc000-0xcfff]
[    0.121177] pci_bus 0000:02: resource 1 [mem 0xfd900000-0xfd9fffff]
[    0.121178] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.121180] pci_bus 0000:03: resource 0 [io  0xb000-0xbfff]
[    0.121182] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.121184] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.121186] pci_bus 0000:04: resource 0 [io  0xd000-0xdfff]
[    0.121187] pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
[    0.121189] pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.121191] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7]
[    0.121192] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff]
[    0.121194] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[    0.121196] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
[    0.121198] pci_bus 0000:04: resource 8 [mem 0x7ff00000-0xfebfffff]
[    0.121231] NET: Registered protocol family 2
[    0.121404] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.121481] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.121591] TCP: Hash tables configured (established 16384 bind 16384)
[    0.121638] TCP: reno registered
[    0.121642] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.121658] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.121721] NET: Registered protocol family 1
[    0.122208] pci 0000:01:00.0: Boot video device
[    0.122214] PCI: CLS 4 bytes, default 64
[    0.122269] Trying to unpack rootfs image as initramfs...
[    0.552248] Freeing initrd memory: 28284K (ffff8800348b2000 - ffff880036451000)
[    0.552480] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
[    0.552484] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
[    0.552551] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.552553] Scanning for low memory corruption every 60 seconds
[    0.552786] Initialise system trusted keyring
[    0.552833] audit: initializing netlink socket (disabled)
[    0.552848] type=2000 audit(1433684262.552:1): initialized
[    0.577957] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.578999] zbud: loaded
[    0.579104] VFS: Disk quotas dquot_6.5.2
[    0.579143] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.579538] fuse init (API version 7.22)
[    0.579601] msgmni has been set to 3995
[    0.579653] Key type big_key registered
[    0.579936] Key type asymmetric registered
[    0.579938] Asymmetric key parser 'x509' registered
[    0.579966] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.579990] io scheduler noop registered
[    0.579992] io scheduler deadline registered (default)
[    0.580028] io scheduler cfq registered
[    0.580193] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.580279] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.580376] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.580434] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.580447] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.580480] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[    0.580482] vesafb: scrolling: redraw
[    0.580483] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    0.580765] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90010400000, using 5120k, total 5120k
[    0.620421] Console: switching to colour frame buffer device 160x64
[    0.660007] fb0: VESA VGA frame buffer device
[    0.660027] intel_idle: does not run on family 6 model 23
[    0.660033] ipmi message handler version 39.2
[    0.660097] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.660101] ACPI: Power Button [PWRB]
[    0.660136] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.660138] ACPI: Power Button [PWRF]
[    0.660247] GHES: HEST is not enabled!
[    0.660312] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.680654] 00:07: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.681764] Linux agpgart interface v0.103
[    0.682936] brd: module loaded
[    0.683517] loop: module loaded
[    0.683606] ata_piix 0000:00:1f.2: version 2.13
[    0.683660] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    0.684150] scsi0 : ata_piix
[    0.684206] scsi1 : ata_piix
[    0.684236] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
[    0.684238] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
[    0.684478] libphy: Fixed MDIO Bus: probed
[    0.684556] tun: Universal TUN/TAP device driver, 1.6
[    0.684557] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.684589] PPP generic driver version 2.4.2
[    0.684618] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.684622] ehci-pci: EHCI PCI platform driver
[    0.684692] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.684699] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.688618] ehci-pci 0000:00:1d.7: cache line size of 4 is not supported
[    0.688636] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
[    0.700019] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.700084] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.700088] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700091] usb usb1: Product: EHCI Host Controller
[    0.700094] usb usb1: Manufacturer: Linux 3.13.0-37-generic ehci_hcd
[    0.700097] usb usb1: SerialNumber: 0000:00:1d.7
[    0.700226] hub 1-0:1.0: USB hub found
[    0.700233] hub 1-0:1.0: 8 ports detected
[    0.700360] ehci-platform: EHCI generic platform driver
[    0.700367] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.700368] ohci-pci: OHCI PCI platform driver
[    0.700376] ohci-platform: OHCI generic platform driver
[    0.700383] uhci_hcd: USB Universal Host Controller Interface driver
[    0.700440] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.700445] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.700465] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
[    0.700500] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.700502] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700504] usb usb2: Product: UHCI Host Controller
[    0.700506] usb usb2: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.700507] usb usb2: SerialNumber: 0000:00:1d.0
[    0.700575] hub 2-0:1.0: USB hub found
[    0.700581] hub 2-0:1.0: 2 ports detected
[    0.700690] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.700697] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.700724] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
[    0.700761] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.700763] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700764] usb usb3: Product: UHCI Host Controller
[    0.700766] usb usb3: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.700768] usb usb3: SerialNumber: 0000:00:1d.1
[    0.700835] hub 3-0:1.0: USB hub found
[    0.700841] hub 3-0:1.0: 2 ports detected
[    0.700956] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.700960] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.700986] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
[    0.701021] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.701023] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.701025] usb usb4: Product: UHCI Host Controller
[    0.701026] usb usb4: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.701028] usb usb4: SerialNumber: 0000:00:1d.2
[    0.701096] hub 4-0:1.0: USB hub found
[    0.701102] hub 4-0:1.0: 2 ports detected
[    0.701209] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.701214] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.701240] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[    0.701275] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.701277] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.701279] usb usb5: Product: UHCI Host Controller
[    0.701280] usb usb5: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.701282] usb usb5: SerialNumber: 0000:00:1d.3
[    0.701348] hub 5-0:1.0: USB hub found
[    0.701354] hub 5-0:1.0: 2 ports detected
[    0.701455] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.701804] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.701812] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.701961] mousedev: PS/2 mouse device common for all mice
[    0.702135] rtc_cmos 00:03: RTC can wake from S4
[    0.702233] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.702254] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.702310] device-mapper: uevent: version 1.0.3
[    0.702362] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.702369] ledtrig-cpu: registered to indicate activity on CPUs
[    0.702453] TCP: cubic registered
[    0.702533] NET: Registered protocol family 10
[    0.702690] NET: Registered protocol family 17
[    0.702701] Key type dns_resolver registered
[    0.702868] Loading compiled-in X.509 certificates
[    0.703764] Loaded X.509 cert 'Magrathea: Glacier signing key: 2cb1133b35f95a9e24deabeeb12ba449bcbabbc9'
[    0.703778] registered taskstats version 1
[    0.705582] Key type trusted registered
[    0.707006] Key type encrypted registered
[    0.708420] AppArmor: AppArmor sha1 policy hashing enabled
[    0.708423] IMA: No TPM chip found, activating TPM-bypass!
[    0.708595] regulator-dummy: disabling
[    0.708625]   Magic number: 3:484:634
[    0.708729] rtc_cmos 00:03: setting system clock to 2015-06-07 13:37:42 UTC (1433684262)
[    0.708923] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.708924] EDD information not available.
[    0.708948] PM: Hibernation image not present or could not be loaded.
[    0.851455] ata1.00: HPA detected: current 488395055, native 488397168
[    0.851461] ata1.00: ATA-7: SAMSUNG HD251HJ, 1AC01113, max UDMA7
[    0.851464] ata1.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.872236] ata1.00: configured for UDMA/133
[    0.872373] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD251HJ  1AC0 PQ: 0 ANSI: 5
[    0.872520] sd 0:0:0:0: [sda] 488395055 512-byte logical blocks: (250 GB/232 GiB)
[    0.872569] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.872592] sd 0:0:0:0: [sda] Write Protect is off
[    0.872596] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.872634] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.930901]  sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[    0.931333] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.932655] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    0.932656] Write protecting the kernel read-only data: 12288k
[    0.934708] Freeing unused kernel memory: 804K (ffff880001737000 - ffff880001800000)
[    0.936421] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[    0.946991] systemd-udevd[109]: starting version 204
[    0.968155] [drm] Initialized drm 1.1.0 20060810
[    0.974805] Floppy drive(s): fd0 is 1.44M
[    0.982896] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.982989] r8169 0000:04:01.0 (unregistered net_device): not PCI Express
[    0.983225] r8169 0000:04:01.0 eth0: RTL8169sb/8110sb at 0xffffc90000368000, c8:3a:35:d5:6c:f7, XID 10000000 IRQ 19
[    0.983228] r8169 0000:04:01.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[    0.992790] FDC 0 is a post-1991 82077
[    0.996187] [drm] radeon kernel modesetting enabled.
[    0.996237] checking generic (d0000000 500000) vs hw (d0000000 10000000)
[    0.996238] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[    0.996254] Console: switching to colour dummy device 80x25
[    0.996535] [drm] initializing kernel modesetting (RV730 0x1002:0x9498 0x1458:0x21C5).
[    0.996628] [drm] register mmio base: 0xFDCE0000
[    0.996629] [drm] register mmio size: 65536
[    0.996704] ATOM BIOS:
[    0.996736] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[    0.996739] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[    0.996740] [drm] Detected VRAM RAM=1024M, BAR=256M
[    0.996741] [drm] RAM width 128bits DDR
[    0.996787] [TTM] Zone  kernel: Available graphics memory: 1024300 kiB
[    0.996788] [TTM] Initializing pool allocator
[    0.996792] [TTM] Initializing DMA pool allocator
[    0.996808] [drm] radeon: 1024M of VRAM memory ready
[    0.996809] [drm] radeon: 1024M of GTT memory ready.
[    0.996818] [drm] Loading RV730 Microcode
[    0.997090] [drm] GART: num cpu pages 262144, num gpu pages 262144
[    1.005230] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[    1.005289] radeon 0000:01:00.0: WB enabled
[    1.005292] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff880035690c00
[    1.005295] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff880035690c0c
[    1.006218] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c598 and cpu addr 0xffffc90010a1c598
[    1.006221] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.006222] [drm] Driver supports precise vblank timestamp query.
[    1.006250] radeon 0000:01:00.0: irq 43 for MSI/MSI-X
[    1.006263] radeon 0000:01:00.0: radeon: using MSI.
[    1.006288] [drm] radeon: irq initialized.
[    1.058331] [drm] ring test on 0 succeeded in 0 usecs
[    1.058391] [drm] ring test on 3 succeeded in 1 usecs
[    1.252937] [drm] ring test on 5 succeeded in 1 usecs
[    1.252944] [drm] UVD initialized successfully.
[    1.253051] [drm] Enabling audio 0 support
[    1.253073] [drm] ib test on ring 0 succeeded in 0 usecs
[    1.253090] [drm] ib test on ring 3 succeeded in 0 usecs
[    1.260018] usb 4-1: new low-speed USB device number 2 using uhci_hcd
[    1.412413] [drm] ib test on ring 5 succeeded
[    1.412743] [drm] Radeon Display Connectors
[    1.412744] [drm] Connector 0:
[    1.412745] [drm]   HDMI-A-1
[    1.412746] [drm]   HPD2
[    1.412748] [drm]   DDC: 0x7f10 0x7f10 0x7f14 0x7f14 0x7f18 0x7f18 0x7f1c 0x7f1c
[    1.412749] [drm]   Encoders:
[    1.412750] [drm]     DFP2: INTERNAL_UNIPHY1
[    1.412751] [drm] Connector 1:
[    1.412752] [drm]   VGA-1
[    1.412754] [drm]   DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[    1.412754] [drm]   Encoders:
[    1.412755] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    1.412756] [drm] Connector 2:
[    1.412758] [drm]   DVI-I-1
[    1.412758] [drm]   HPD1
[    1.412760] [drm]   DDC: 0x7e20 0x7e20 0x7e24 0x7e24 0x7e28 0x7e28 0x7e2c 0x7e2c
[    1.412761] [drm]   Encoders:
[    1.412762] [drm]     DFP1: INTERNAL_UNIPHY
[    1.412763] [drm]     CRT2: INTERNAL_KLDSCP_DAC2
[    1.412782] [drm] Internal thermal controller with fan control
[    1.414556] [drm] radeon: dpm initialized
[    1.429018] usb 4-1: New USB device found, idVendor=275d, idProduct=0a29
[    1.429020] usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.429022] usb 4-1: Product: USB OPTICAL MOUSE
[    1.434962] hidraw: raw HID events driver (C) Jiri Kosina
[    1.452290] usbcore: registered new interface driver usbhid
[    1.452292] usbhid: USB HID core driver
[    1.453663] input: USB OPTICAL MOUSE  as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input5
[    1.453741] hid-generic 0003:275D:0A29.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:1d.2-1/input0
[    1.462873] [drm] fb mappable at 0xD045E000
[    1.462874] [drm] vram apper at 0xD0000000
[    1.462876] [drm] size 5242880
[    1.462877] [drm] fb depth is 24
[    1.462878] [drm]    pitch is 5120
[    1.462923] fbcon: radeondrmfb (fb0) is primary device
[    1.463170] Console: switching to colour frame buffer device 160x64
[    1.465947] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    1.465948] radeon 0000:01:00.0: registered panic notifier
[    1.465957] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
[    1.552019] tsc: Refined TSC clocksource calibration: 2933.332 MHz
[    1.672025] usb 5-1: new low-speed USB device number 2 using uhci_hcd
[    1.851277] usb 5-1: New USB device found, idVendor=046d, idProduct=c248
[    1.851283] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.851286] usb 5-1: Product: Gaming Keyboard G105
[    1.851289] usb 5-1: Manufacturer: Logitech
[    1.872247] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    1.877652] input: Logitech Gaming Keyboard G105 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/input/input6
[    1.877809] hid-generic 0003:046D:C248.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Gaming Keyboard G105] on usb-0000:00:1d.3-1/input0
[    1.943331] input: Logitech Gaming Keyboard G105 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.1/input/input7
[    1.943590] hid-generic 0003:046D:C248.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [Logitech Gaming Keyboard G105] on usb-0000:00:1d.3-1/input1
[    2.443292] random: init urandom read with 119 bits of entropy available
[    2.552061] Switched to clocksource tsc
[    2.679406] random: nonblocking pool is initialized
[   13.136484] Adding 4881404k swap on /dev/sda7.  Priority:-1 extents:1 across:4881404k FS
[   13.156061] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   13.218770] systemd-udevd[346]: starting version 204
[   13.320880] lp: driver loaded but no devices found
[   13.330417] ppdev: user-space parallel port driver
[   13.333294] parport_pc 00:08: reported by Plug and Play ACPI
[   13.333339] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   13.393431] intel_rng: FWH not detected
[   13.402824] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[   13.430742] lp0: using parport0 (interrupt-driven).
[   13.444237] device-mapper: multipath: version 1.6.0 loaded
[   13.446779] SKU: Nid=0x1d sku_cfg=0x4005c603
[   13.446783] SKU: port_connectivity=0x1
[   13.446784] SKU: enable_pcbeep=0x0
[   13.446785] SKU: check_sum=0x00000005
[   13.446786] SKU: customization=0x000000c6
[   13.446787] SKU: external_amp=0x0
[   13.446788] SKU: platform_type=0x0
[   13.446789] SKU: swap=0x1
[   13.446790] SKU: override=0x1
[   13.447104] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   13.447106]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   13.447107]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   13.447108]    mono: mono_out=0x0
[   13.447109]    dig-out=0x1e/0x0
[   13.447110]    inputs:
[   13.447111]      Rear Mic=0x18
[   13.447113]      Front Mic=0x19
[   13.447114]      Line=0x1a
[   13.447115]      CD=0x1c
[   13.447116] realtek: No valid SSID, checking pincfg 0x4005c603 for NID 0x1d
[   13.447118] realtek: Enabling init ASM_ID=0xc603 CODEC_ID=10ec0887
[   13.450168] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[   13.472807] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   13.472892] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   13.473174] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   13.473575] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   13.473654] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   13.474023] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20131115/utaddress-251)
[   13.474028] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   13.474063] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   13.475348] leds_ss4200: no LED devices found
[   13.475443] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   13.475445] hda-intel 0000:01:00.1: Using LPIB position fix
[   13.475477] snd_hda_intel 0000:01:00.1: irq 45 for MSI/MSI-X
[   13.504641] hda-intel 0000:01:00.1: Enable sync_write for stable communication
[   13.509833] HDMI ATI/AMD: no speaker allocation for ELD
[   13.509944] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   13.888837] gpio_ich: GPIO from 206 to 255 on gpio_ich
[   14.382127] init: failsafe main process (606) killed by TERM signal
[   14.883415] Bluetooth: Core ver 2.17
[   14.883433] NET: Registered protocol family 31
[   14.883435] Bluetooth: HCI device and connection manager initialized
[   14.883479] Bluetooth: HCI socket layer initialized
[   14.883481] Bluetooth: L2CAP socket layer initialized
[   14.883485] Bluetooth: SCO socket layer initialized
[   14.887151] Bluetooth: RFCOMM TTY layer initialized
[   14.887162] Bluetooth: RFCOMM socket layer initialized
[   14.887167] Bluetooth: RFCOMM ver 1.11
[   14.889196] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.889199] Bluetooth: BNEP filters: protocol multicast
[   14.889207] Bluetooth: BNEP socket layer initialized
[   15.546472] init: cups main process (677) killed by HUP signal
[   15.546484] init: cups main process ended, respawning
[   17.808525] r8169 0000:04:01.0 eth0: link down
[   17.808534] r8169 0000:04:01.0 eth0: link down
[   17.808548] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.808731] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.933725] init: samba-ad-dc main process (735) terminated with status 1
[   20.561528] init: plymouth-upstart-bridge main process ended, respawning
[   20.573793] init: plymouth-upstart-bridge main process ended, respawning



dmesg | tail

Kod Seç Genişlet

[   14.889207] Bluetooth: BNEP socket layer initialized
[   15.546472] init: cups main process (677) killed by HUP signal
[   15.546484] init: cups main process ended, respawning
[   17.808525] r8169 0000:04:01.0 eth0: link down
[   17.808534] r8169 0000:04:01.0 eth0: link down
[   17.808548] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.808731] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.933725] init: samba-ad-dc main process (735) terminated with status 1
[   20.561528] init: plymouth-upstart-bridge main process ended, respawning
[   20.573793] init: plymouth-upstart-bridge main process ended, respawning

[heartsmagic]

Atheros'a ait modül de görünmüyor gibi ortalıkta, hani acaba bir karışıklık mı var diye düşündüm. Gerçi tek arayüz görünüyor o da Realtek olan kartın modülünü kullanıyor. Elle IP aldığın zaman nereye kadar gidebiliyorsun görmemiz lazım. Şimdi diyelim ki modem 192.168.1.1 adresini kullanıyor. Buna göre adımları değiştir.

Kod Seç Genişlet

sudo ifconfig eth0 192.168.1.100
sudo route add default gw 192.168.1.1


Bu aşamadan sonra şu çıktıları bir görelim:

Kod Seç Genişlet

ifconfig
ping 192.168.1.1
ping 173.194.44.72
ping google.com

[CeeMoo]

~ $ sudo ifconfig eth0 192.168.2.100

~ $ sudo route add default gw 192.168.2.1

~ $ ifconfig

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr c8:3a:35:d5:6c:f7 
          inet addr:192.168.2.100  Bcast:192.168.2.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:147 errors:0 dropped:0 overruns:0 frame:0
          TX packets:147 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:10545 (10.5 KB)  TX bytes:10545 (10.5 KB)


~ $ ping 192.168.2.1

Kod Seç Genişlet

PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
From 192.168.2.100 icmp_seq=1 Destination Host Unreachable
From 192.168.2.100 icmp_seq=5 Destination Host Unreachable
From 192.168.2.100 icmp_seq=6 Destination Host Unreachable
From 192.168.2.100 icmp_seq=7 Destination Host Unreachable
From 192.168.2.100 icmp_seq=8 Destination Host Unreachable

--- 192.168.2.1 ping statistics ---
10 packets transmitted, 0 received, +5 errors, 100% packet loss, time 8999ms
pipe 4

~ $ ping 173.194.44.72

Kod Seç Genişlet

PING 173.194.44.72 (173.194.44.72) 56(84) bytes of data.
From 192.168.2.100 icmp_seq=1 Destination Host Unreachable
From 192.168.2.100 icmp_seq=2 Destination Host Unreachable
From 192.168.2.100 icmp_seq=3 Destination Host Unreachable
From 192.168.2.100 icmp_seq=4 Destination Host Unreachable
From 192.168.2.100 icmp_seq=5 Destination Host Unreachable
From 192.168.2.100 icmp_seq=6 Destination Host Unreachable

--- 173.194.44.72 ping statistics ---
7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6029ms
pipe 3

$ ping google.com

Kod Seç Genişlet

ping: unknown host google.com
$ ping google.com

Kod Seç Genişlet

ping: unknown host google.com

Aslında sıkıntı şu : sisteme giriyorum harici internet kartı kendini kapatıyor.Işık tepkime vs.. vermiyor. :Z

Aslında minik bir usb wifi ile iş çözülür boşuna vakit kaybetmeyelim.İlginiz alakanız için Teşekkür ederim.

[heartsmagic]

Modemi dahi pingleyememişiz, garip. Gerçi bir de şu çıktıyı görsek fena olmazmış, istemeyi unutmuşum:

Kod Seç Genişlet

route -n
Eğer çıktı vereceksen aynı işlemleri tekrar yapman gerekecek tabi. Fakat, anlattıklarından gördüğümüz harici kartın bir şekilde devre dışı kalıyor oluşu.

[CeeMoo]

Tabi şöyle ekleyeyim.

~ $ sudo ifconfig eth0 192.168.2.63

~ $ sudo route add default gw 192.168.2.1

cat /etc/lsb-release

Kod Seç Genişlet

DISTRIB_ID=LinuxMint
DISTRIB_RELEASE=17.1
DISTRIB_CODENAME=rebecca
DISTRIB_DESCRIPTION="Linux Mint 17.1 Rebecca"
uname -a
Linux cee-G31M-ES2L 3.13.0-37-generic #64-Ubuntu SMP Mon Sep 22 21:28:38 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 01)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01)
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01)
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV730 PRO [Radeon HD 4650]
01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] RV710/730 HDMI Audio [Radeon HD 4000 series]
04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8169 PCI Gigabit Ethernet Controller (rev 10)

lsusb

Kod Seç Genişlet

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 046d:c248 Logitech, Inc.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 275d:0a29 
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
rfkill list 
lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 046d:c248 Logitech, Inc.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 275d:0a29 
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

sudo lshw -C network

Kod Seç Genişlet

  *-network               
       description: Ethernet interface
       product: RTL8169 PCI Gigabit Ethernet Controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 1
       bus info: pci@0000:04:01.0
       logical name: eth0
       version: 10
       serial: c8:3a:35:d5:6c:f7
       size: 10Mbit/s
       capacity: 1Gbit/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half ip=192.168.2.63 latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s
       resources: irq:19 ioport:de00(size=256) memory:fdbff000-fdbff0ff memory:fda00000-fda1ffff

ifconfig

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr c8:3a:35:d5:6c:f7 
          inet addr:192.168.2.63  Bcast:192.168.2.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:171 errors:0 dropped:0 overruns:0 frame:0
          TX packets:171 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:12817 (12.8 KB)  TX bytes:12817 (12.8 KB)

iwconfig

Kod Seç Genişlet

eth0      no wireless extensions.

lo        no wireless extensions.

iwlist scanning

Kod Seç Genişlet

eth0      Interface doesn't support scanning.

lo        Interface doesn't support scanning.

lsmod

Kod Seç Genişlet

Module                  Size  Used by
bnep                   19624  2
rfcomm                 69160  0
bluetooth             391136  10 bnep,rfcomm
binfmt_misc            17468  1
gpio_ich               13476  0
snd_hda_codec_hdmi     46368  1
snd_hda_codec_realtek    65580  1
snd_hda_intel          56451  5
snd_hda_codec         192906  3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_hwdep              13602  1 snd_hda_codec
snd_pcm               102099  3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc         18710  2 snd_pcm,snd_hda_intel
snd_seq_midi           13324  0
snd_seq_midi_event     14899  1 snd_seq_midi
snd_rawmidi            30144  1 snd_seq_midi
snd_seq                61560  2 snd_seq_midi_event,snd_seq_midi
snd_seq_device         14497  3 snd_seq,snd_rawmidi,snd_seq_midi
dm_multipath           22873  0
coretemp               13435  0
snd_timer              29482  2 snd_pcm,snd_seq
scsi_dh                14882  1 dm_multipath
kvm                   451552  0
serio_raw              13462  0
lpc_ich                21080  0
snd                    69322  21 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
soundcore              12680  1 snd
mac_hid                13205  0
parport_pc             32701  1
ppdev                  17671  0
lp                     17759  0
parport                42348  3 lp,ppdev,parport_pc
dm_mirror              22135  0
dm_region_hash         20862  1 dm_mirror
dm_log                 18411  2 dm_region_hash,dm_mirror
hid_generic            12548  0
usbhid                 52659  0
hid                   106148  2 hid_generic,usbhid
radeon               1522526  3
psmouse               106678  0
r8169                  67581  0
mii                    13934  1 r8169
floppy                 69418  0
i2c_algo_bit           13413  1 radeon
ttm                    85150  1 radeon
drm_kms_helper         55071  1 radeon
drm                   303102  5 ttm,drm_kms_helper,radeon

dmesg

Kod Seç Genişlet

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.13.0-37-generic (buildd@kapok) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #64-Ubuntu SMP Mon Sep 22 21:28:38 UTC 2014 (Ubuntu 3.13.0-37.64-generic 3.13.11.7)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-37-generic root=UUID=11ccce5c-5a27-4ee6-8b31-2e45db6ffd14 ro quiet splash vt.handoff=7
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007fedffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007fee0000-0x000000007fee2fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007fee3000-0x000000007feeffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007fef0000-0x000000007fefffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.4 present.
[    0.000000] DMI: Gigabyte Technology Co., Ltd. G31M-ES2L/G31M-ES2L, BIOS FH 04/30/2010
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x7fee0 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-through
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 07FF00000 mask FFFF00000 uncachable
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[    0.000000] total RAM covered: 2047M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K chunk_size: 2M num_reg: 2  lose cover RAM: 0G
[    0.000000] New variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[    0.000000] found SMP MP-table at [mem 0x000f53c0-0x000f53cf] mapped at [ffff8800000f53c0]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE
[    0.000000] BRK [0x01fe2000, 0x01fe2fff] PGTABLE
[    0.000000] BRK [0x01fe3000, 0x01fe3fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7fc00000-0x7fdfffff]
[    0.000000]  [mem 0x7fc00000-0x7fdfffff] page 2M
[    0.000000] BRK [0x01fe4000, 0x01fe4fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7c000000-0x7fbfffff]
[    0.000000]  [mem 0x7c000000-0x7fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x7bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x7fe00000-0x7fedffff]
[    0.000000]  [mem 0x7fe00000-0x7fedffff] page 4k
[    0.000000] BRK [0x01fe5000, 0x01fe5fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x348b2000-0x36450fff]
[    0.000000] ACPI: RSDP 00000000000f6db0 000014 (v00 GBT   )
[    0.000000] ACPI: RSDT 000000007fee3040 00003C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: FACP 000000007fee30c0 000074 (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: DSDT 000000007fee3180 0040E8 (v01 GBT    GBTUACPI 00001000 MSFT 0100000C)
[    0.000000] ACPI: FACS 000000007fee0000 000040
[    0.000000] ACPI: HPET 000000007fee73c0 000038 (v01 GBT    GBTUACPI 42302E31 GBTU 00000098)
[    0.000000] ACPI: MCFG 000000007fee7440 00003C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: TAMG 000000007fee7480 00625A (v01 GBT    GBT   B0 5455312E BG?? 00020101)
[    0.000000] ACPI: APIC 000000007fee72c0 000084 (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[    0.000000] ACPI: SSDT 000000007feedd40 0003AB (v01  PmRef    CpuPm 00003000 INTL 20040311)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000007fedffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x7fedffff]
[    0.000000]   NODE_DATA [mem 0x7fedb000-0x7fedffff]
[    0.000000]  [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0x7fedffff]
[    0.000000] On node 0 totalpages: 523902
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 8124 pages used for memmap
[    0.000000]   DMA32 zone: 519904 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] e820: [mem 0x7ff00000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 29 pages/cpu @ffff88007fc00000 s86400 r8192 d24192 u524288
[    0.000000] pcpu-alloc: s86400 r8192 d24192 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 515693
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-37-generic root=UUID=11ccce5c-5a27-4ee6-8b31-2e45db6ffd14 ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 2017452K/2095608K available (7375K kernel code, 1144K rwdata, 3404K rodata, 1336K init, 1444K bss, 78156K reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000] Offload RCU callbacks from all CPUs
[    0.000000] Offload RCU callbacks from CPUs: 0-3.
[    0.000000] NR_IRQS:16640 nr_irqs:712 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 8388608 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2933.437 MHz processor
[    0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5866.87 BogoMIPS (lpj=11733748)
[    0.004007] pid_max: default: 32768 minimum: 301
[    0.004044] Security Framework initialized
[    0.004070] AppArmor: AppArmor initialized
[    0.004071] Yama: becoming mindful.
[    0.004253] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.008756] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.009269] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.009273] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.009520] Initializing cgroup subsys memory
[    0.009528] Initializing cgroup subsys devices
[    0.009531] Initializing cgroup subsys freezer
[    0.009532] Initializing cgroup subsys blkio
[    0.009534] Initializing cgroup subsys perf_event
[    0.009536] Initializing cgroup subsys hugetlb
[    0.009560] CPU: Physical Processor ID: 0
[    0.009562] CPU: Processor Core ID: 0
[    0.009564] mce: CPU supports 6 MCE banks
[    0.009571] CPU0: Thermal monitoring enabled (TM2)
[    0.009578] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[    0.009578] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
[    0.009578] tlb_flushall_shift: -1
[    0.009674] Freeing SMP alternatives memory: 32K (ffffffff81e6e000 - ffffffff81e76000)
[    0.010998] ACPI: Core revision 20131115
[    0.012274] ACPI: All ACPI Tables successfully acquired
[    0.013417] ftrace: allocating 28541 entries in 112 pages
[    0.020455] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.061669] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU     E7500  @ 2.93GHz (fam: 06, model: 17, stepping: 0a)
[    0.064000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[    0.064000] ... version:                2
[    0.064000] ... bit width:              40
[    0.064000] ... generic registers:      2
[    0.064000] ... value mask:             000000ffffffffff
[    0.064000] ... max period:             000000007fffffff
[    0.064000] ... fixed-purpose events:   3
[    0.064000] ... event mask:             0000000700000003
[    0.064000] x86: Booting SMP configuration:
[    0.064000] .... node  #0, CPUs:      #1
[    0.074884] x86: Booted up 1 node, 2 CPUs
[    0.074888] smpboot: Total of 2 processors activated (11733.74 BogoMIPS)
[    0.074988] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.076126] devtmpfs: initialized
[    0.076198] EVM: security.selinux
[    0.076199] EVM: security.SMACK64
[    0.076201] EVM: security.ima
[    0.076202] EVM: security.capability
[    0.076221] PM: Registering ACPI NVS region [mem 0x7fee0000-0x7fee2fff] (12288 bytes)
[    0.076890] pinctrl core: initialized pinctrl subsystem
[    0.076957] regulator-dummy: no parameters
[    0.076983] RTC time: 13:35:36, date: 06/14/15
[    0.077021] NET: Registered protocol family 16
[    0.077123] cpuidle: using governor ladder
[    0.077125] cpuidle: using governor menu
[    0.077154] ACPI: bus type PCI registered
[    0.077156] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.077208] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.077210] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.089372] PCI: Using configuration type 1 for base access
[    0.092051] bio: create slab <bio-0> at 0
[    0.092070] ACPI: Added _OSI(Module Device)
[    0.092072] ACPI: Added _OSI(Processor Device)
[    0.092073] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.092075] ACPI: Added _OSI(Processor Aggregator Device)
[    0.093453] ACPI BIOS Warning (bug): Incorrect checksum in table [TAMG] - 0x51, should be 0x50 (20131115/tbprint-214)
[    0.093547] ACPI: SSDT 000000007feed720 00026C (v01  PmRef  Cpu0Ist 00003000 INTL 20040311)
[    0.093662] ACPI: Dynamic OEM Table Load:
[    0.093665] ACPI: SSDT           (null) 00026C (v01  PmRef  Cpu0Ist 00003000 INTL 20040311)
[    0.093729] ACPI: SSDT 000000007feedbe0 000152 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.093836] ACPI: Dynamic OEM Table Load:
[    0.093838] ACPI: SSDT           (null) 000152 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.093937] ACPI: Interpreter enabled
[    0.093943] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
[    0.093946] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[    0.093957] ACPI: (supports S0 S3 S4 S5)
[    0.093959] ACPI: Using IOAPIC for interrupt routing
[    0.093984] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.094058] ACPI: No dock devices found.
[    0.097392] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.097398] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.097402] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.097585] PCI host bridge to bus 0000:00
[    0.097588] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.097590] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.097592] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.097593] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.097595] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.097597] pci_bus 0000:00: root bus resource [mem 0x7ff00000-0xfebfffff]
[    0.097604] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
[    0.097682] pci 0000:00:01.0: [8086:29c1] type 01 class 0x060400
[    0.097714] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.097792] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.097805] pci 0000:00:1b.0: reg 0x10: [mem 0xfdff8000-0xfdffbfff 64bit]
[    0.097861] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.097900] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.097928] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.097985] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.098024] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.098053] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.098110] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.098150] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.098180] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.098213] pci 0000:00:1d.0: reg 0x20: [io  0xff00-0xff1f]
[    0.098262] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.098287] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.098320] pci 0000:00:1d.1: reg 0x20: [io  0xfe00-0xfe1f]
[    0.098368] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.098395] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.098428] pci 0000:00:1d.2: reg 0x20: [io  0xfd00-0xfd1f]
[    0.098476] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.098504] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.098538] pci 0000:00:1d.3: reg 0x20: [io  0xfc00-0xfc1f]
[    0.098586] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.098617] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.098631] pci 0000:00:1d.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
[    0.098724] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.098751] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.098821] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.098851] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
[    0.098920] pci 0000:00:1f.0: address space collision: [io  0x0400-0x047f] conflicts with ACPI CPU throttle [??? 0x00000410-0x00000415 flags 0x80000000]
[    0.098924] pci 0000:00:1f.0: quirk: [io  0x0480-0x04bf] claimed by ICH6 GPIO
[    0.098927] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f)
[    0.098930] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f)
[    0.099010] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x010180
[    0.099022] pci 0000:00:1f.2: reg 0x10: [io  0x0000-0x0007]
[    0.099029] pci 0000:00:1f.2: reg 0x14: [io  0x0000-0x0003]
[    0.099035] pci 0000:00:1f.2: reg 0x18: [io  0x0000-0x0007]
[    0.099042] pci 0000:00:1f.2: reg 0x1c: [io  0x0000-0x0003]
[    0.099049] pci 0000:00:1f.2: reg 0x20: [io  0xf900-0xf90f]
[    0.099077] pci 0000:00:1f.2: PME# supported from D3hot
[    0.099136] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.099180] pci 0000:00:1f.3: reg 0x20: [io  0x0500-0x051f]
[    0.099285] pci 0000:01:00.0: [1002:9498] type 00 class 0x030000
[    0.099297] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.099306] pci 0000:01:00.0: reg 0x18: [mem 0xfdce0000-0xfdceffff 64bit]
[    0.099313] pci 0000:01:00.0: reg 0x20: [io  0xae00-0xaeff]
[    0.099324] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.099350] pci 0000:01:00.0: supports D1 D2
[    0.099384] pci 0000:01:00.1: [1002:aa38] type 00 class 0x040300
[    0.099395] pci 0000:01:00.1: reg 0x10: [mem 0xfdcfc000-0xfdcfffff 64bit]
[    0.099445] pci 0000:01:00.1: supports D1 D2
[    0.099487] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.099490] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.099492] pci 0000:00:01.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.099495] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.099536] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.099539] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.099542] pci 0000:00:1c.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.099547] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.099588] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.099591] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.099594] pci 0000:00:1c.1:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.099599] pci 0000:00:1c.1:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.099632] pci 0000:04:01.0: [10ec:8169] type 00 class 0x020000
[    0.099648] pci 0000:04:01.0: reg 0x10: [io  0xde00-0xdeff]
[    0.099656] pci 0000:04:01.0: reg 0x14: [mem 0xfdbff000-0xfdbff0ff]
[    0.099693] pci 0000:04:01.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.099717] pci 0000:04:01.0: supports D1 D2
[    0.099718] pci 0000:04:01.0: PME# supported from D1 D2 D3hot
[    0.099778] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.099781] pci 0000:00:1e.0:   bridge window [io  0xd000-0xdfff]
[    0.099785] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.099789] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.099791] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.099793] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.099795] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.099797] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.099798] pci 0000:00:1e.0:   bridge window [mem 0x7ff00000-0xfebfffff] (subtractive decode)
[    0.100185] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.100231] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.100275] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.100320] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.100364] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100409] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100454] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.100500] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.100575] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.100580] ACPI: \_SB_.PCI0: notify handler is installed
[    0.100602] Found 1 acpi root devices
[    0.100674] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.100674] vgaarb: loaded
[    0.100674] vgaarb: bridge control possible 0000:01:00.0
[    0.100674] SCSI subsystem initialized
[    0.100674] libata version 3.00 loaded.
[    0.100674] ACPI: bus type USB registered
[    0.100674] usbcore: registered new interface driver usbfs
[    0.100674] usbcore: registered new interface driver hub
[    0.100674] usbcore: registered new device driver usb
[    0.100674] PCI: Using ACPI for IRQ routing
[    0.108876] PCI: pci_cache_line_size set to 64 bytes
[    0.108911] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[    0.108912] e820: reserve RAM buffer [mem 0x7fee0000-0x7fffffff]
[    0.108996] NetLabel: Initializing
[    0.108998] NetLabel:  domain hash size = 128
[    0.108998] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.109012] NetLabel:  unlabeled traffic allowed by default
[    0.109022] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.109022] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.109022] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.110053] Switched to clocksource hpet
[    0.113571] AppArmor: AppArmor Filesystem Enabled
[    0.113618] pnp: PnP ACPI init
[    0.113635] ACPI: bus type PNP registered
[    0.113795] system 00:00: [io  0x04d0-0x04d1] has been reserved
[    0.113798] system 00:00: [io  0x0290-0x029f] has been reserved
[    0.113800] system 00:00: [io  0x0800-0x087f] has been reserved
[    0.113802] system 00:00: [io  0x0290-0x0294] has been reserved
[    0.113804] system 00:00: [io  0x0880-0x088f] has been reserved
[    0.113807] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.113817] pnp 00:01: [dma 4]
[    0.113832] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.113905] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.113939] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.113961] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.113985] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.114075] pnp 00:06: [dma 2]
[    0.114103] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.114262] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.114420] pnp 00:08: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.114528] system 00:09: [io  0x0400-0x04cf] could not be reserved
[    0.114531] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.114687] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.114690] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.114811] system 00:0b: [mem 0x000f0000-0x000f3fff] could not be reserved
[    0.114814] system 00:0b: [mem 0x000f4000-0x000f7fff] could not be reserved
[    0.114816] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.114818] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.114820] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved
[    0.114822] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.114824] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved
[    0.114827] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.114829] system 00:0b: [mem 0xfed13000-0xfed1dfff] has been reserved
[    0.114831] system 00:0b: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.114833] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.114835] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved
[    0.114836] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
[    0.114838] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
[    0.114841] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.114871] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[    0.114875] pnp: PnP ACPI: found 13 devices
[    0.114876] ACPI: bus type PNP unregistered
[    0.121093] pci 0000:00:1f.0: BAR 13: [io  0x0400-0x047f] has bogus alignment
[    0.121100] pci 0000:01:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref]
[    0.121102] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.121104] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.121107] pci 0000:00:01.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.121110] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.121113] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.121116] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.121120] pci 0000:00:1c.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.121123] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.121128] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.121130] pci 0000:00:1c.1:   bridge window [io  0xb000-0xbfff]
[    0.121134] pci 0000:00:1c.1:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.121137] pci 0000:00:1c.1:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.121142] pci 0000:04:01.0: BAR 6: assigned [mem 0xfda00000-0xfda1ffff pref]
[    0.121145] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.121147] pci 0000:00:1e.0:   bridge window [io  0xd000-0xdfff]
[    0.121151] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.121154] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.121159] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.121161] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.121163] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.121164] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.121166] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff]
[    0.121168] pci_bus 0000:01: resource 0 [io  0xa000-0xafff]
[    0.121170] pci_bus 0000:01: resource 1 [mem 0xfdc00000-0xfdcfffff]
[    0.121172] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.121174] pci_bus 0000:02: resource 0 [io  0xc000-0xcfff]
[    0.121175] pci_bus 0000:02: resource 1 [mem 0xfd900000-0xfd9fffff]
[    0.121177] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.121179] pci_bus 0000:03: resource 0 [io  0xb000-0xbfff]
[    0.121181] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.121182] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
[    0.121184] pci_bus 0000:04: resource 0 [io  0xd000-0xdfff]
[    0.121186] pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
[    0.121188] pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.121189] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7]
[    0.121191] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff]
[    0.121193] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[    0.121195] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
[    0.121196] pci_bus 0000:04: resource 8 [mem 0x7ff00000-0xfebfffff]
[    0.121230] NET: Registered protocol family 2
[    0.121403] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.121477] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.121588] TCP: Hash tables configured (established 16384 bind 16384)
[    0.121636] TCP: reno registered
[    0.121640] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.121656] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.121719] NET: Registered protocol family 1
[    0.122207] pci 0000:01:00.0: Boot video device
[    0.122212] PCI: CLS 4 bytes, default 64
[    0.122268] Trying to unpack rootfs image as initramfs...
[    0.552240] Freeing initrd memory: 28284K (ffff8800348b2000 - ffff880036451000)
[    0.552473] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
[    0.552476] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
[    0.552543] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.552545] Scanning for low memory corruption every 60 seconds
[    0.552778] Initialise system trusted keyring
[    0.552825] audit: initializing netlink socket (disabled)
[    0.552840] type=2000 audit(1434288936.552:1): initialized
[    0.577942] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.578983] zbud: loaded
[    0.579089] VFS: Disk quotas dquot_6.5.2
[    0.579128] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.579525] fuse init (API version 7.22)
[    0.579588] msgmni has been set to 3995
[    0.579640] Key type big_key registered
[    0.579924] Key type asymmetric registered
[    0.579926] Asymmetric key parser 'x509' registered
[    0.579954] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.579979] io scheduler noop registered
[    0.579980] io scheduler deadline registered (default)
[    0.580016] io scheduler cfq registered
[    0.580183] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.580269] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.580366] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.580424] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.580436] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.580470] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[    0.580472] vesafb: scrolling: redraw
[    0.580473] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    0.580755] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90010400000, using 5120k, total 5120k
[    0.620412] Console: switching to colour frame buffer device 160x64
[    0.659992] fb0: VESA VGA frame buffer device
[    0.660020] intel_idle: does not run on family 6 model 23
[    0.660026] ipmi message handler version 39.2
[    0.660089] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.660093] ACPI: Power Button [PWRB]
[    0.660127] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.660130] ACPI: Power Button [PWRF]
[    0.660239] GHES: HEST is not enabled!
[    0.660305] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.680645] 00:07: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.681760] Linux agpgart interface v0.103
[    0.682933] brd: module loaded
[    0.683512] loop: module loaded
[    0.683602] ata_piix 0000:00:1f.2: version 2.13
[    0.683657] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    0.684145] scsi0 : ata_piix
[    0.684201] scsi1 : ata_piix
[    0.684230] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
[    0.684232] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
[    0.684472] libphy: Fixed MDIO Bus: probed
[    0.684550] tun: Universal TUN/TAP device driver, 1.6
[    0.684551] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.684584] PPP generic driver version 2.4.2
[    0.684614] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.684617] ehci-pci: EHCI PCI platform driver
[    0.684688] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.684694] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.688605] ehci-pci 0000:00:1d.7: cache line size of 4 is not supported
[    0.688624] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
[    0.700018] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.700085] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.700089] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700092] usb usb1: Product: EHCI Host Controller
[    0.700095] usb usb1: Manufacturer: Linux 3.13.0-37-generic ehci_hcd
[    0.700098] usb usb1: SerialNumber: 0000:00:1d.7
[    0.700226] hub 1-0:1.0: USB hub found
[    0.700233] hub 1-0:1.0: 8 ports detected
[    0.700361] ehci-platform: EHCI generic platform driver
[    0.700368] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.700370] ohci-pci: OHCI PCI platform driver
[    0.700377] ohci-platform: OHCI generic platform driver
[    0.700385] uhci_hcd: USB Universal Host Controller Interface driver
[    0.700442] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.700446] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.700466] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
[    0.700502] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.700504] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700506] usb usb2: Product: UHCI Host Controller
[    0.700507] usb usb2: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.700509] usb usb2: SerialNumber: 0000:00:1d.0
[    0.700576] hub 2-0:1.0: USB hub found
[    0.700582] hub 2-0:1.0: 2 ports detected
[    0.700691] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.700698] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.700725] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
[    0.700761] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.700763] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.700765] usb usb3: Product: UHCI Host Controller
[    0.700767] usb usb3: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.700768] usb usb3: SerialNumber: 0000:00:1d.1
[    0.700837] hub 3-0:1.0: USB hub found
[    0.700842] hub 3-0:1.0: 2 ports detected
[    0.700956] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.700961] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.700987] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
[    0.701022] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.701024] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.701026] usb usb4: Product: UHCI Host Controller
[    0.701027] usb usb4: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.701029] usb usb4: SerialNumber: 0000:00:1d.2
[    0.701097] hub 4-0:1.0: USB hub found
[    0.701103] hub 4-0:1.0: 2 ports detected
[    0.701211] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.701215] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.701241] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[    0.701277] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.701279] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.701280] usb usb5: Product: UHCI Host Controller
[    0.701282] usb usb5: Manufacturer: Linux 3.13.0-37-generic uhci_hcd
[    0.701284] usb usb5: SerialNumber: 0000:00:1d.3
[    0.701350] hub 5-0:1.0: USB hub found
[    0.701356] hub 5-0:1.0: 2 ports detected
[    0.701455] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.701814] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.701821] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.701971] mousedev: PS/2 mouse device common for all mice
[    0.702142] rtc_cmos 00:03: RTC can wake from S4
[    0.702239] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.702261] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.702316] device-mapper: uevent: version 1.0.3
[    0.702368] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.702375] ledtrig-cpu: registered to indicate activity on CPUs
[    0.702461] TCP: cubic registered
[    0.702541] NET: Registered protocol family 10
[    0.702698] NET: Registered protocol family 17
[    0.702708] Key type dns_resolver registered
[    0.702876] Loading compiled-in X.509 certificates
[    0.703774] Loaded X.509 cert 'Magrathea: Glacier signing key: 2cb1133b35f95a9e24deabeeb12ba449bcbabbc9'
[    0.703788] registered taskstats version 1
[    0.705593] Key type trusted registered
[    0.707018] Key type encrypted registered
[    0.708425] AppArmor: AppArmor sha1 policy hashing enabled
[    0.708428] IMA: No TPM chip found, activating TPM-bypass!
[    0.708600] regulator-dummy: disabling
[    0.708630]   Magic number: 3:459:584
[    0.708732] rtc_cmos 00:03: setting system clock to 2015-06-14 13:35:37 UTC (1434288937)
[    0.708925] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.708927] EDD information not available.
[    0.708950] PM: Hibernation image not present or could not be loaded.
[    0.851455] ata1.00: HPA detected: current 488395055, native 488397168
[    0.851461] ata1.00: ATA-7: SAMSUNG HD251HJ, 1AC01113, max UDMA7
[    0.851465] ata1.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.872236] ata1.00: configured for UDMA/133
[    0.872374] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD251HJ  1AC0 PQ: 0 ANSI: 5
[    0.872520] sd 0:0:0:0: [sda] 488395055 512-byte logical blocks: (250 GB/232 GiB)
[    0.872570] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.872593] sd 0:0:0:0: [sda] Write Protect is off
[    0.872597] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.872633] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.937273]  sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[    0.937706] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.939019] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    0.939021] Write protecting the kernel read-only data: 12288k
[    0.941081] Freeing unused kernel memory: 804K (ffff880001737000 - ffff880001800000)
[    0.942782] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[    0.953382] systemd-udevd[109]: starting version 204
[    0.975019] [drm] Initialized drm 1.1.0 20060810
[    0.984714] Floppy drive(s): fd0 is 1.44M
[    0.990376] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.990469] r8169 0000:04:01.0 (unregistered net_device): not PCI Express
[    0.990705] r8169 0000:04:01.0 eth0: RTL8169sb/8110sb at 0xffffc90000368000, c8:3a:35:d5:6c:f7, XID 10000000 IRQ 19
[    0.990707] r8169 0000:04:01.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[    1.002050] [drm] radeon kernel modesetting enabled.
[    1.002096] checking generic (d0000000 500000) vs hw (d0000000 10000000)
[    1.002098] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[    1.002114] Console: switching to colour dummy device 80x25
[    1.003681] FDC 0 is a post-1991 82077
[    1.003947] [drm] initializing kernel modesetting (RV730 0x1002:0x9498 0x1458:0x21C5).
[    1.003960] [drm] register mmio base: 0xFDCE0000
[    1.003961] [drm] register mmio size: 65536
[    1.004067] ATOM BIOS:
[    1.004099] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[    1.004101] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[    1.004103] [drm] Detected VRAM RAM=1024M, BAR=256M
[    1.004104] [drm] RAM width 128bits DDR
[    1.004144] [TTM] Zone  kernel: Available graphics memory: 1024300 kiB
[    1.004146] [TTM] Initializing pool allocator
[    1.004149] [TTM] Initializing DMA pool allocator
[    1.004168] [drm] radeon: 1024M of VRAM memory ready
[    1.004169] [drm] radeon: 1024M of GTT memory ready.
[    1.004178] [drm] Loading RV730 Microcode
[    1.004448] [drm] GART: num cpu pages 262144, num gpu pages 262144
[    1.016466] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[    1.016611] radeon 0000:01:00.0: WB enabled
[    1.016614] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff880035e17c00
[    1.016617] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff880035e17c0c
[    1.017423] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c598 and cpu addr 0xffffc90010a1c598
[    1.017425] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.017426] [drm] Driver supports precise vblank timestamp query.
[    1.017449] radeon 0000:01:00.0: irq 43 for MSI/MSI-X
[    1.017464] radeon 0000:01:00.0: radeon: using MSI.
[    1.017488] [drm] radeon: irq initialized.
[    1.077092] [drm] ring test on 0 succeeded in 0 usecs
[    1.077152] [drm] ring test on 3 succeeded in 1 usecs
[    1.252021] usb 4-2: new low-speed USB device number 2 using uhci_hcd
[    1.271655] [drm] ring test on 5 succeeded in 1 usecs
[    1.271658] [drm] UVD initialized successfully.
[    1.271755] [drm] Enabling audio 0 support
[    1.271776] [drm] ib test on ring 0 succeeded in 0 usecs
[    1.271791] [drm] ib test on ring 3 succeeded in 0 usecs
[    1.421015] usb 4-2: New USB device found, idVendor=275d, idProduct=0a29
[    1.421017] usb 4-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.421019] usb 4-2: Product: USB OPTICAL MOUSE
[    1.429960] hidraw: raw HID events driver (C) Jiri Kosina
[    1.431050] [drm] ib test on ring 5 succeeded
[    1.431519] [drm] Radeon Display Connectors
[    1.431521] [drm] Connector 0:
[    1.431522] [drm]   HDMI-A-1
[    1.431523] [drm]   HPD2
[    1.431525] [drm]   DDC: 0x7f10 0x7f10 0x7f14 0x7f14 0x7f18 0x7f18 0x7f1c 0x7f1c
[    1.431526] [drm]   Encoders:
[    1.431527] [drm]     DFP2: INTERNAL_UNIPHY1
[    1.431528] [drm] Connector 1:
[    1.431529] [drm]   VGA-1
[    1.431530] [drm]   DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[    1.431531] [drm]   Encoders:
[    1.431532] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    1.431533] [drm] Connector 2:
[    1.431534] [drm]   DVI-I-1
[    1.431535] [drm]   HPD1
[    1.431537] [drm]   DDC: 0x7e20 0x7e20 0x7e24 0x7e24 0x7e28 0x7e28 0x7e2c 0x7e2c
[    1.431537] [drm]   Encoders:
[    1.431538] [drm]     DFP1: INTERNAL_UNIPHY
[    1.431539] [drm]     CRT2: INTERNAL_KLDSCP_DAC2
[    1.431559] [drm] Internal thermal controller with fan control
[    1.433460] [drm] radeon: dpm initialized
[    1.447407] usbcore: registered new interface driver usbhid
[    1.447409] usbhid: USB HID core driver
[    1.449932] input: USB OPTICAL MOUSE  as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5
[    1.450727] hid-generic 0003:275D:0A29.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:1d.2-2/input0
[    1.482609] [drm] fb mappable at 0xD045E000
[    1.482611] [drm] vram apper at 0xD0000000
[    1.482612] [drm] size 5242880
[    1.482613] [drm] fb depth is 24
[    1.482614] [drm]    pitch is 5120
[    1.482660] fbcon: radeondrmfb (fb0) is primary device
[    1.482904] Console: switching to colour frame buffer device 160x64
[    1.485674] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    1.485676] radeon 0000:01:00.0: registered panic notifier
[    1.485696] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
[    1.552016] tsc: Refined TSC clocksource calibration: 2933.333 MHz
[    1.664035] usb 5-1: new low-speed USB device number 2 using uhci_hcd
[    1.843278] usb 5-1: New USB device found, idVendor=046d, idProduct=c248
[    1.843285] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.843288] usb 5-1: Product: Gaming Keyboard G105
[    1.843291] usb 5-1: Manufacturer: Logitech
[    1.869718] input: Logitech Gaming Keyboard G105 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/input/input6
[    1.869797] hid-generic 0003:046D:C248.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Gaming Keyboard G105] on usb-0000:00:1d.3-1/input0
[    1.928463] EXT4-fs (sda6): INFO: recovery required on readonly filesystem
[    1.928466] EXT4-fs (sda6): write access will be enabled during recovery
[    1.935356] input: Logitech Gaming Keyboard G105 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.1/input/input7
[    1.935502] hid-generic 0003:046D:C248.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [Logitech Gaming Keyboard G105] on usb-0000:00:1d.3-1/input1
[    2.547680] random: nonblocking pool is initialized
[    2.552063] Switched to clocksource tsc
[    3.462831] EXT4-fs (sda6): recovery complete
[    3.478618] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   14.851361] Adding 4881404k swap on /dev/sda7.  Priority:-1 extents:1 across:4881404k FS
[   14.910760] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.023662] systemd-udevd[348]: starting version 204
[   15.142094] lp: driver loaded but no devices found
[   15.151785] ppdev: user-space parallel port driver
[   15.154610] parport_pc 00:08: reported by Plug and Play ACPI
[   15.154654] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   15.195283] intel_rng: FWH not detected
[   15.218944] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[   15.221712] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20131115/utaddress-251)
[   15.221718] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.221741] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   15.222914] leds_ss4200: no LED devices found
[   15.249947] lp0: using parport0 (interrupt-driven).
[   15.284211] kvm: disabled by bios
[   15.308017] device-mapper: multipath: version 1.6.0 loaded
[   15.383795] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[   15.394752] SKU: Nid=0x1d sku_cfg=0x4005c603
[   15.394755] SKU: port_connectivity=0x1
[   15.394756] SKU: enable_pcbeep=0x0
[   15.394757] SKU: check_sum=0x00000005
[   15.394758] SKU: customization=0x000000c6
[   15.394759] SKU: external_amp=0x0
[   15.394760] SKU: platform_type=0x0
[   15.394761] SKU: swap=0x1
[   15.394762] SKU: override=0x1
[   15.395078] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   15.395080]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   15.395081]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   15.395082]    mono: mono_out=0x0
[   15.395083]    dig-out=0x1e/0x0
[   15.395084]    inputs:
[   15.395086]      Rear Mic=0x18
[   15.395087]      Front Mic=0x19
[   15.395088]      Line=0x1a
[   15.395089]      CD=0x1c
[   15.395091] realtek: No valid SSID, checking pincfg 0x4005c603 for NID 0x1d
[   15.395092] realtek: Enabling init ASM_ID=0xc603 CODEC_ID=10ec0887
[   15.405217] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   15.405348] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   15.405427] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   15.405505] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   15.405584] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   15.405970] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   15.405972] hda-intel 0000:01:00.1: Using LPIB position fix
[   15.406006] snd_hda_intel 0000:01:00.1: irq 45 for MSI/MSI-X
[   15.408292] hda-intel 0000:01:00.1: Enable sync_write for stable communication
[   15.416590] HDMI ATI/AMD: no speaker allocation for ELD
[   15.416646] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   15.582767] gpio_ich: GPIO from 206 to 255 on gpio_ich
[   15.745687] init: failsafe main process (609) killed by TERM signal
[   16.324198] Bluetooth: Core ver 2.17
[   16.324229] NET: Registered protocol family 31
[   16.324230] Bluetooth: HCI device and connection manager initialized
[   16.324244] Bluetooth: HCI socket layer initialized
[   16.324246] Bluetooth: L2CAP socket layer initialized
[   16.324250] Bluetooth: SCO socket layer initialized
[   16.328569] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   16.328573] Bluetooth: BNEP filters: protocol multicast
[   16.328583] Bluetooth: BNEP socket layer initialized
[   16.329386] Bluetooth: RFCOMM TTY layer initialized
[   16.329397] Bluetooth: RFCOMM socket layer initialized
[   16.329404] Bluetooth: RFCOMM ver 1.11
[   16.995227] init: cups main process (696) killed by HUP signal
[   16.995237] init: cups main process ended, respawning
[   19.292507] r8169 0000:04:01.0 eth0: link down
[   19.292517] r8169 0000:04:01.0 eth0: link down
[   19.292538] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.292730] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.374925] init: samba-ad-dc main process (749) terminated with status 1
[   21.287034] init: plymouth-upstart-bridge main process ended, respawning
[   21.291362] init: plymouth-upstart-bridge main process (1284) terminated with status 1
[   21.291372] init: plymouth-upstart-bridge main process ended, respawning

dmesg | tail

Kod Seç Genişlet

[   16.995227] init: cups main process (696) killed by HUP signal
[   16.995237] init: cups main process ended, respawning
[   19.292507] r8169 0000:04:01.0 eth0: link down
[   19.292517] r8169 0000:04:01.0 eth0: link down
[   19.292538] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.292730] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.374925] init: samba-ad-dc main process (749) terminated with status 1
[   21.287034] init: plymouth-upstart-bridge main process ended, respawning
[   21.291362] init: plymouth-upstart-bridge main process (1284) terminated with status 1
[   21.291372] init: plymouth-upstart-bridge main process ended, respawning


route -n

Kod Seç Genişlet

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.2.1     0.0.0.0         UG    0      0        0 eth0
192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0

ping 192.168.2.1

Kod Seç Genişlet

PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
From 192.168.2.63 icmp_seq=1 Destination Host Unreachable
From 192.168.2.63 icmp_seq=2 Destination Host Unreachable
From 192.168.2.63 icmp_seq=3 Destination Host Unreachable
From 192.168.2.63 icmp_seq=4 Destination Host Unreachable
From 192.168.2.63 icmp_seq=5 Destination Host Unreachable
From 192.168.2.63 icmp_seq=6 Destination Host Unreachable
--- 192.168.2.1 ping statistics ---
7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6030ms
pipe 3

ping 173.194.44.72

Kod Seç Genişlet

PING 173.194.44.72 (173.194.44.72) 56(84) bytes of data.
From 192.168.2.63 icmp_seq=1 Destination Host Unreachable
From 192.168.2.63 icmp_seq=2 Destination Host Unreachable
From 192.168.2.63 icmp_seq=3 Destination Host Unreachable
From 192.168.2.63 icmp_seq=4 Destination Host Unreachable
From 192.168.2.63 icmp_seq=5 Destination Host Unreachable
From 192.168.2.63 icmp_seq=6 Destination Host Unreachable
--- 173.194.44.72 ping statistics ---
7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6013ms
pipe 3

ping google.com

Kod Seç Genişlet

ping: unknown host google.com

[if]

@CeeMoo, bu kart için Realtek'in sunduğu sürücü bu[1] sanırım. Mint mi kullanıyorsunuz? Mint çekirdek güncellemelerini öntanımlı olarak kapatıyor. Güncellemeleri açıp çekirdek sürümünü yükseltin. Çözüm olmazsa çekirdeği elle yükleriz.

[1] http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110S-32%2FRTL8110SB%20L%20%2FRTL8169SB%20L%20%2FRTL8169SC%20L%20%20br%3ERTL8169

[CeeMoo]

@CeeMoo, bu kart için Realtek'in sunduğu sürücü bu[1] sanırım. Mint mi kullanıyorsunuz? Mint çekirdek güncellemelerini öntanımlı olarak kapatıyor. Güncellemeleri açıp çekirdek sürümünü yükseltin. Çözüm olmazsa çekirdeği elle yükleriz.

[1] http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110S-32%2FRTL8110SB%20L%20%2FRTL8169SB%20L%20%2FRTL8169SC%20L%20%20br%3ERTL8169

Bende yüklemeye çalıştım ama başaramadım.Bunun tam yüklemesini nasıl yapabilirim.

[heartsmagic]

@if'in söylemek istediği önce bir çekirdeği yükseltmen. Mint'in arayüzü olan bir uygulaması var bunun için sanırım. Onu kullanarak en yüksek sürümlü çekirdeğe sistemi yükseltip sonra sistemi yeniden başlat. Bakalım kart tepki verecek mi. Bana sürücü ile ilgili bir şey değil gibi geliyor ama hiç garantisi yok bu işlerin tabi.

[CeeMoo]

@if'in söylemek istediği önce bir çekirdeği yükseltmen. Mint'in arayüzü olan bir uygulaması var bunun için sanırım. Onu kullanarak en yüksek sürümlü çekirdeğe sistemi yükseltip sonra sistemi yeniden başlat. Bakalım kart tepki verecek mi. Bana sürücü ile ilgili bir şey değil gibi geliyor ama hiç garantisi yok bu işlerin tabi.

@heartsmagic @if Sorunu modemi ilk ayarlarına alarak çözdüm.Nasıl böyle birşey oldu gerçekten bilmiyorum.Emeğiniz ilginiz alakanız için Teşekkürler.