[Çözüldü] Her yeniden başlama sonrası yazıcıyı tanımıyor.

[s.corpara]

arkadaşlar
sistem Lubuntu 13.04
Yazıcı Samsung-4623fn
samsung un sitesinden indirdiğim sürücüyü kurarken aşağıdaki kodlarını kullanıyorum, sorunsuz yüklüyor, çıktıda alabiliyorum fakat yeniden başlattığım zaman yazıcıyı görmüyor ne yazık ki. her yazdırma işleminde kodları giriyorum bir çözümü varmıdır bunun.
başlangıçta samsungun smartpanel programı geliyor fakat sürücü hatası veriyor.
"please install supported driver or port" şeklinde.

Kod Seç Genişlet

sudo tar zxvf UnifiedLinuxDriver_1.10.tar.gz
cd cdroot/Linux
chmod +x install.sh
sudo ./install.sh

edit : yazılımsal olduğunu düşündüğüm için bu kısma açtım ama sorun olmaz umarım kusura bakmayın.

[heartsmagic]

install.sh dosyasının içeriğini buraya geçer misin?
Sürücünün böyle sistem yeniden başladıktan sonra uçup gitmesi bir garip.

[s.corpara]

system-config-printer
yazıyorum,
WARNING: gnome-keyring:: couldn't connect to: /run/user/scorp/keyring-YQNZno/pkcs11: Böyle bir dosya ya da dizin yok
böyle bir uyarı veriyor fakat yazıcılar penceresi açılıyor.


bağlan a tıkladığımda aşşağıdaki pencere geliyor,

sadece localhost var seçeneklerde bağlan diyorum,ve aşağıdaki hata geliyor.

tekrar sürücü yüklemesi yaptım, durum aşşağıdaki gibi, 4623f olarak gözükeni kurdum diğerini önceden kurmuştum, kurulum sonrası oda gözüktü.

yazıcıya belge gönderiyorum fakat artık yazdırmıyorda.

aslında şunuda farkettim tekraryükleme yaptığımda bir önceki oturumda tanıttığım yazıcıda çıkıyor. bu arada yazıcı ethernetle ağa bağlı, ağ üzerinden kullanıyorum


install.sh aşağıdaki gibi

Kod Seç Genişlet

#! /bin/sh
# {

### Common procedures

wait_to_allow_to_see_info_line() {
sleep 1
}

abort_execution() {
echo "ERROR: $1, execution aborted"
wait_to_allow_to_see_info_line
exit 4
}

set_variables() {
if test -z "$OEM_FILE" ; then
OEM_FILE=OEM.ini
fi

### Set VENDOR, VENDOR_UC, VENDOR_LC

VENDOR=`grep '^VENDOR=' $OEM_FILE 2>/dev/null | sed 's/VENDOR=\(.*\)/\1/'`
if [ -z $VENDOR ]; then
VENDOR="Unknown"
fi
VENDOR_UC=`echo $VENDOR | tr a-z A-Z`
VENDOR_LC=`echo $VENDOR | tr A-Z a-z`

### Set LINUX_DIST

ISSUE=`cat /etc/issue 2>/dev/null`
LINUX_DIST=
if   ( echo $ISSUE | grep -q "Red Hat Linux release 7.1" ); then
LINUX_DIST="REDHAT_71"
elif ( echo $ISSUE | grep -q "Red Hat Linux release 7.2" ); then
LINUX_DIST="REDHAT_72"
elif ( echo $ISSUE | grep -q "Red Hat Linux release 7.3" ); then
LINUX_DIST="REDHAT_73"
elif ( echo $ISSUE | grep -q "Red Hat Linux release 8" ); then
LINUX_DIST="REDHAT_8"
elif ( echo $ISSUE | grep -q "Red Hat Linux release 9" ); then
LINUX_DIST="REDHAT_9"
elif ( echo $ISSUE | grep -q "Red Hat Enterprise Linux*.*.release 4" ); then
LINUX_DIST="RHEL_4"
elif ( echo $ISSUE | grep -q "Fedora Core release 1.92" ); then
LINUX_DIST="FEDORA_192"
elif ( echo $ISSUE | grep -q "Fedora Core release 2.90" ); then
LINUX_DIST="FEDORA_290"
elif ( echo $ISSUE | grep -q "Fedora Core release 3" ); then
LINUX_DIST="FEDORA_300"
elif ( echo $ISSUE | grep -q "Fedora release" ); then
LINUX_DIST="FEDORA_7_AND_ABOVE"
elif ( echo $ISSUE | grep -q "SuSE Linux 8.0" ); then
LINUX_DIST="SUSE_80"
elif ( echo $ISSUE | grep -q "SuSE Linux 8.1" ); then
LINUX_DIST="SUSE_81"
elif ( echo $ISSUE | grep -q "SuSE Linux 8.2" ); then
LINUX_DIST="SUSE_82"
elif ( echo $ISSUE | grep -q "SuSE Linux 9.0" ); then
LINUX_DIST="SUSE_90"
elif ( echo $ISSUE | grep -q "SuSE Linux 9.1" ); then
LINUX_DIST="SUSE_91"
elif ( echo $ISSUE | grep -q "SuSE Linux 9.2" ); then
LINUX_DIST="SUSE_92"
elif ( echo $ISSUE | grep -q "SuSE Linux 9.3" ); then
LINUX_DIST="SUSE_93"
elif ( echo $ISSUE | grep -q "Linux Mandrake release 8.0" ); then
LINUX_DIST="MANDRAKE_80"
elif ( echo $ISSUE | grep -q "Mandrake Linux release 8.1" ); then
LINUX_DIST="MANDRAKE_81"
elif ( echo $ISSUE | grep -q "Mandrake Linux release 8.2" ); then
LINUX_DIST="MANDRAKE_82"
elif ( echo $ISSUE | grep -q "Mandrake Linux release 9.0" ); then
LINUX_DIST="MANDRAKE_90"
elif ( echo $ISSUE | grep -q "Mandrake Linux release 10.0" ); then
LINUX_DIST="MANDRAKE_100"
elif ( echo $ISSUE | grep -q "Mandrakelinux release 10.2beta2" ); then
LINUX_DIST="MANDRAKE_102B2"
elif ( echo $ISSUE | grep -q "Mandriva Linux release 2006.0" ); then
LINUX_DIST="MANDRIVA_2006_0"
elif ( echo $ISSUE | grep -q "Mandriva Linux release 200[7-9]\|Mandriva Linux release 20[1-9]" ); then
LINUX_DIST="MANDRIVA_2007_AND_ABOVE"
elif ( echo $ISSUE | grep -q "Caldera OpenLinux 3.1.1" ); then
LINUX_DIST="CALDERA_311"
elif ( echo $ISSUE | grep -q "Turbolinux.*7.0" ); then
LINUX_DIST="TURBOLINUX_70"
elif ( echo $ISSUE | grep -q "Turbolinux" ); then
LINUX_DIST="TURBOLINUX"
elif ( echo $ISSUE | grep -q "Ubuntu 5.10" ); then
LINUX_DIST="UBUNTU_510"
elif ( echo $ISSUE | grep -q "Ubuntu" ); then
LINUX_DIST="UBUNTU"
fi

if [ -z "$LINUX_DIST" ]; then
if [ -f /etc/slackware-version ]; then
SLACKWARE_VERSION=`cat /etc/slackware-version 2>/dev/null`
if   ( echo $SLACKWARE_VERSION | grep -q "Slackware 8.1" ); then
LINUX_DIST="SLACKWARE_81"
else
LINUX_DIST="SLACKWARE"
fi
elif [ -f /etc/guadalinex_version ]; then
GUADALINEX_VERSION=`cat /etc/guadalinex_version 2>/dev/null`
if   ( echo $GUADALINEX_VERSION | grep -q "guadalinex-rc15" ); then
LINUX_DIST="GUADALINEX_10"
elif   ( echo $GUADALINEX_VERSION | grep -q "Final.*2004" ); then
LINUX_DIST="GUADALINEX_2004"
else
LINUX_DIST="GUADALINEX"
fi
elif [ -f /etc/knoppix-version ]; then
KNOPPIX_VERSION=`cat /etc/knoppix-version 2>/dev/null`
if   ( echo $KNOPPIX_VERSION | grep -q "3.8.1" ); then
LINUX_DIST="KNOPPIX_381"
else
LINUX_DIST="KNOPPIX"
fi
fi
fi

HARDWARE_PLATFORM=`uname -m`
if [ "$HARDWARE_PLATFORM" = "i486" -o "$HARDWARE_PLATFORM" = "i586" -o "$HARDWARE_PLATFORM" = "i686" ]; then
HARDWARE_PLATFORM=i386
fi
# Set platform library directory suffix PLSFX
if [ "$HARDWARE_PLATFORM" = "x86_64" ]; then
PLSFX=64
else
PLSFX=
fi

if test -c /dev/usb/lp0 ; then
PRINTER_GROUP=`ls -l /dev/usb/lp0 2> /dev/null | awk '{print $4}'`
#d echo "/dev/usb/lp0" " found" ", group is " $PRINTER_GROUP
elif test -c /dev/usblp0 ; then
PRINTER_GROUP=`ls -l /dev/usblp0 2> /dev/null | awk '{print $4}'`
#d echo "/dev/usblp0" " found" ", group is " $PRINTER_GROUP
elif test -d /var/spool/cups ; then
PRINTER_GROUP=`ls -ld /var/spool/cups 2> /dev/null | awk '{print $4}'`
#d echo "/var/spool/cups" " found" ", group is " $PRINTER_GROUP
else
PRINTER_GROUP="lp"
fi

INSTALL_DIR_MFP=/opt/$VENDOR/mfp
INSTALL_DIR_COMMON=/opt/smfp-common

# $DECHO "VENDOR=$VENDOR"
# $DECHO "VENDOR_UC=$VENDOR_UC"
# $DECHO "VENDOR_LC=$VENDOR_LC"
# $DECHO "LINUX_DIST=$LINUX_DIST"
# $DECHO "HARDWARE_PLATFORM=$HARDWARE_PLATFORM"
# $DECHO "PLSFX=$PLSFX"
}

show_versions() {
test -r noarch/at_opt/share/VERSION-Common_LINUX   && echo "Common_LINUX   `cat noarch/at_opt/share/VERSION-Common_LINUX`"
test -r noarch/at_opt/share/VERSION-Printer_LINUX  && echo "Printer_LINUX  `cat noarch/at_opt/share/VERSION-Printer_LINUX`"
test -r noarch/at_opt/share/VERSION-Scanner_LINUX  && echo "Scanner_LINUX  `cat noarch/at_opt/share/VERSION-Scanner_LINUX`"
test -r noarch/at_opt/share/VERSION-BUILD          && echo "BUILD          `cat noarch/at_opt/share/VERSION-BUILD`"
test -r noarch/at_opt/share/VERSION-Common_SCRIPT  && echo "Common_SCRIPT  `cat noarch/at_opt/share/VERSION-Common_SCRIPT`"
test -r noarch/at_opt/share/VERSION-Scanner_SCRIPT && echo "Scanner_SCRIPT `cat noarch/at_opt/share/VERSION-Scanner_SCRIPT`"
test -r noarch/at_opt/share/VERSION-Printer_SCRIPT && echo "Printer_SCRIPT `cat noarch/at_opt/share/VERSION-Printer_SCRIPT`"

test -r smartpanel/bin${PLSFX}/.version            && echo "SmartPanel     `cat smartpanel/bin${PLSFX}/.version`"
test -r psu/bin${PLSFX}/.version                   && echo "PSU            `cat psu/bin${PLSFX}/.version`"
test -r phonebook/bin${PLSFX}/.version             && echo "PhoneBook      `cat phonebook/bin${PLSFX}/.version`"
test -r emailbook/bin${PLSFX}/.version             && echo "EmailBook      `cat emailbook/bin${PLSFX}/.version`"
test -r smartpanel/bin${PLSFX}/.script-version     && echo "SmartPn_SCRIPT `cat smartpanel/bin${PLSFX}/.script-version`"
test -r psu/bin${PLSFX}/.script-version            && echo "PSU_SCRIPT     `cat psu/bin${PLSFX}/.script-version`"
}

# Funcrion copy_directories accepts two parameters
# $1 - the list of source directories
# $2 - destination directory
# $1 may be empty string, in this case function does nothing
#
# Function copies directory trees from the set of source directories
# to destination directory. Subdirectories are created as needed.
#
# Ownership and permissions of created subdirectories are
# correspondent to the executing shell process.
#
# Ownership of copied files is set to root:root.
# Permissions of copied files are preserved.

copy_directories() {
if ! test -d $2 ; then
echo "ERROR: Destination directory $2 does not exist. Copy operation aborted."
return
fi
dst_dir=$2
for src_dir in $1 ; do
if ! test -d $src_dir ; then
echo "ERROR: Source directory $src_dir does not exist"
else
( cd $src_dir && find . -type d ) | grep -v ^\.$ | \
sed -e "s:\(^\./\)\(.*\):mkdir -p \"$dst_dir/\2\":" | /bin/sh
( cd $src_dir && find . -type f -o -type l ) | \
sed -e "s:\(^\./\)\(.*\):cp -af \"$src_dir/\2\" \"$dst_dir/\2\" ; chown root\:root \"$dst_dir/\2\":" | /bin/sh
fi
done
}

ensure_proc_bus_usb_mounted() {
if test -d /proc/bus/usb && test -z "`ls /proc/bus/usb 2> /dev/null | grep -v '^\.'`" ; then
# If directory does exist and is empty
mount /proc/bus/usb 2> /dev/null
fi
}

shell_script_execution_disable() {
test -n "$1" || return
test -n "$MODIFIER_ID_STRING" || return
TMP_FILE_ENA=/tmp/`basename $1`-dis.tmp
cat $1 > $TMP_FILE_ENA
echo "exit 0    # $MODIFIER_ID_STRING" > $1
cat $TMP_FILE_ENA >> $1
rm -f $TMP_FILE_ENA
}

shell_script_execution_enable() {
test -n "$1" || return
test -n "$MODIFIER_ID_STRING" || return
TMP_FILE_DIS=/tmp/`basename $1`-ena.tmp
cat $1 | grep -v "`echo $MODIFIER_ID_STRING`" > $TMP_FILE_DIS
cat $TMP_FILE_DIS > $1
rm -f $TMP_FILE_DIS
}

check_package()
{
if [ -f /etc/slackware-version ]; then
result=`ls /var/log/packages/$1-* 2> /dev/null`
rv=$?
result=`echo $result | awk -F '-' '{print $2}'`
else
result=`rpm -q --queryformat '%{VERSION}' $1 2>/dev/null`
rv=$?
fi
return $rv
}

detect_system_packages() {
CUPS_DETECTED=1
GS_DETECTED=1
SANE_DETECTED=1

if ! check_package cups ; then
if ! test -f /etc/cups/printers.conf && ! test -e /usr/sbin/cupsd ; then
CUPS_DETECTED=0
fi
fi
if ! check_package ghostscript ; then
if test -z "`gs --version 2> /dev/null`" ; then
GS_DETECTED=0
fi
fi
if ! check_package sane ; then
if ! check_package sane-backends ; then
if ! test -f /usr/lib${PLSFX}/libsane.so.1 ; then
SANE_DETECTED=0
fi
fi
fi
}

check_related_packages() {
TOTAL_RELATED_PACKAGES_INSTALLED=`ls -ld /opt/*/mfp/uninstall/guiuninstall 2> /dev/null | wc | awk '{print $1}'`
}

set_firmware_device_name() {
if [ "$MODEL" = "CLP-200splc" ]; then
FIRMWARE_DEVICE_NAME="CLP-200 Series"
elif [ "$MODEL" = "CLP-300splc" ]; then
FIRMWARE_DEVICE_NAME="CLP-300 Series"
elif [ "$MODEL" = "mfp560" ]; then
FIRMWARE_DEVICE_NAME="MFP 560 Series"
elif [ "$MODEL" = "mfp750" ]; then
FIRMWARE_DEVICE_NAME="MFP 750 Series"
elif [ "$MODEL" = "clx3160" ]; then
FIRMWARE_DEVICE_NAME="CLX-3160 Series"
elif [ "$MODEL" = "scx4100" ]; then
FIRMWARE_DEVICE_NAME="SCX-4100 Series"
elif [ "$MODEL" = "scx4200" ]; then
FIRMWARE_DEVICE_NAME="SCX-4200 Series"
elif [ "$MODEL" = "scx4x16" ]; then
FIRMWARE_DEVICE_NAME="SCX-4x16 Series"
elif [ "$MODEL" = "scx4x20" ]; then
FIRMWARE_DEVICE_NAME="SCX-4x20 Series"
elif [ "$MODEL" = "scx4x21" ]; then
FIRMWARE_DEVICE_NAME="SCX-4x21 Series"
elif [ "$MODEL" = "scx5312f" ]; then
FIRMWARE_DEVICE_NAME="SCX-5x12 Series"
elif [ "$MODEL" = "scx5x30" ]; then
FIRMWARE_DEVICE_NAME="SCX-5x30 Series"
elif [ "$MODEL" = "scx6x20" ]; then
FIRMWARE_DEVICE_NAME="SCX-6x20 Series"
elif [ "$MODEL" = "scx6x22ps" ]; then
FIRMWARE_DEVICE_NAME="SCX-6x22 Series"
elif [ "$MODEL" = "sf531p" ]; then
FIRMWARE_DEVICE_NAME="SF-530 Series"
else
FIRMWARE_DEVICE_NAME=
fi
}

check_icc_redist() {

REDIST_ARC="noarch/icc-redist-i386.tar.gz"
if test -d "/usr/lib" -a -f $REDIST_ARC ; then
zcat $REDIST_ARC | tar -xf - -C / 2> /dev/null
fi

REDIST_ARC="noarch/icc-redist-x86_64.tar.gz"
if test -d "/usr/lib64" -a -f $REDIST_ARC ; then
zcat $REDIST_ARC | tar -xf - -C / 2> /dev/null
fi
}

check_libstdcxx() {

LIBSTDCXX_FILES=`ls /usr/lib${PLSFX}/libstdc++.so.5* 2> /dev/null`
LIBSTDCXX_ARC="noarch/libstdc++-5-${HARDWARE_PLATFORM}.tar.gz"
if test -z "$LIBSTDCXX_FILES" -a -f $LIBSTDCXX_ARC ; then
echo -n "libstdc++.so.5 (gcc 3.0.x .. 3.3.x) not found, install ... "
zcat $LIBSTDCXX_ARC | tar -xf - -C / 2> /dev/null
ldconfig
echo "done"
fi
}

check_libtiff() {

LIBTIFF_FILES=`ls /usr/lib${PLSFX}/libtiff.so.3* 2> /dev/null`
LIBTIFF_ARC="noarch/libtiff-3-${HARDWARE_PLATFORM}.tar.gz"
if test -z "$LIBTIFF_FILES" -a -f $LIBTIFF_ARC ; then
echo -n "libtiff.so.3 not found, install ... "
zcat $LIBTIFF_ARC | tar -xf - -C / 2> /dev/null
ldconfig
echo "done"
fi
}

check_libqt() {
COMMON_LIB_DIR=$INSTALL_DIR_COMMON/lib$PLSFX

if ! test -f "${COMMON_LIB_DIR}/libqt-mt.so.3.0.5" ; then
mkdir -p "$COMMON_LIB_DIR" && \
cp -a ${HARDWARE_PLATFORM}/lib${PLSFX}/libqt-mt.so.3 ${COMMON_LIB_DIR}/libqt-mt.so.3.0.5 && \
cp -a ${HARDWARE_PLATFORM}/lib${PLSFX}/libqui.so.1   ${COMMON_LIB_DIR}/libqui.so.1.0.0 && \
( cd "$COMMON_LIB_DIR" && \
ln -s -f libqt-mt.so.3.0.5 libqt-mt.so.3.0 ; \
ln -s -f libqt-mt.so.3.0.5 libqt-mt.so.3   ; \
ln -s -f libqt-mt.so.3.0.5 libqt-mt.so     ; \
ln -s -f libqui.so.1.0.0 libqui.so.1.0     ; \
ln -s -f libqui.so.1.0.0 libqui.so.1       ; \
ln -s -f libqui.so.1.0.0 libqui.so         ; \
)
fi
}

copy_base_files() {
mkdir -p $MFP_INSTALL_DIR || abort_execution "Can not create directory $MFP_INSTALL_DIR"

#x echo "INFO: Installing common files ..."
copy_directories "${HARDWARE_PLATFORM}/at_opt" $MFP_INSTALL_DIR
if [ "$QT_MODE" = "$QT_MODE_QT4" ]; then
#x echo "INFO: Installing Qt4 applications ..."
#x wait_to_allow_to_see_info_line
# TEMP:
#xxx mv /opt/Samsung/mfp/uninstall/guiuninstall /tmp/
copy_directories "${HARDWARE_PLATFORM}/qt4apps/at_opt" $MFP_INSTALL_DIR
#xxx mv /tmp/guiuninstall /opt/Samsung/mfp/uninstall/
elif [ "$QT_MODE" = "$QT_MODE_QT_SUPPLIED" ]; then
check_libqt
fi
#x# copy_directories "${HARDWARE_PLATFORM}/lib${PLSFX}" $MFP_INSTALL_DIR/lib
copy_directories "${HARDWARE_PLATFORM}/at_root" /
( cd "/opt/smfp-common/lib${PLSFX}" && \
ln -s -f libnetsnmp.so.10.0.2 libnetsnmp.so.10; \
)
copy_directories "noarch/at_opt" $MFP_INSTALL_DIR
copy_directories "noarch/at_root" /
find $MFP_INSTALL_DIR -exec chown root:root \{\} \;
chmod 755 /usr/lib*/cups/filter/rastertosamsung*
chmod 755 /usr/lib*/cups/filter/smfpautoconf
}

create_script_start_web_browser() {
mkdir -p /opt/$VENDOR/mfp/bin
cat > /opt/$VENDOR/mfp/bin/start_web_browser.sh <<EOF
#!/bin/sh
WEB_BROWSER=\`which firefox 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which mozilla 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which konqueror 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which galeon 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which opera 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which netscape 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which epiphany 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=\`which mozilla-firefox 2> /dev/null\`
if test -z "\$WEB_BROWSER" ; then
WEB_BROWSER=true
fi
fi
fi
fi
fi
fi
fi
fi
\$WEB_BROWSER \$1
EOF

chmod 755 /opt/$VENDOR/mfp/bin/start_web_browser.sh
}

write_desktop_directory() {
if test -z "$1" ; then
return 1
fi
cat > $1 <<EOF
[Desktop Entry]
Name=$VENDOR Unified Driver
Name[C]=$VENDOR Unified Driver
Comment=$VENDOR Unified Driver
Comment[C]=$VENDOR Unified Driver
Icon=/opt/$VENDOR/mfp/share/images/Configurator.png
Type=Directory
EOF
}

fix_desktop_file_ownership() {
DIR_NAME=`dirname $1`
DIR_LSLDN=`ls -ldn $DIR_NAME 2> /dev/null`
OWNERSHIP="`echo $DIR_LSLDN | awk '{print \$3}'`:`echo $DIR_LSLDN | awk '{print \$4}'`"

if test -n "$OWNERSHIP" ; then
chown "$OWNERSHIP" $1
fi

chmod 755 $1
}

write_configurator_desktop_file() {
if test -z "$1" ; then
return 1
fi
cat > $1 <<EOF
[Desktop Entry]
Name=$VENDOR Unified Driver Configurator
Name[C]=$VENDOR Unified Driver Configurator
Comment=Manage your printers and scanners here
Comment[C]=Manage your printers and scanners here
Type=Application
Exec=/opt/$VENDOR/mfp/bin/Configurator
Path=/opt/$VENDOR/mfp/bin
Icon=/opt/$VENDOR/mfp/share/images/Configurator.png
Terminal=0
TerminalOptions=
X-KDE-SubstituteUID=false
X-KDE-Username=
EOF

fix_desktop_file_ownership $1
}

write_toner_reorder_desktop_file() {
VENDOR_C=$VENDOR
if [ "$VENDOR" = "DELL" ] ; then
VENDOR_C=Dell
URL_SUPPLIERS=http://www.dell.com/supplies
else
return 0
fi
if test -z "$1" ; then
return 1
fi
cat > $1 <<EOF
[Desktop Entry]
Name=$VENDOR_C Toner Reorder
Name[C]=$VENDOR_C Toner Reorder
Comment=Order Toner Cartridge Online
Comment[C]=Order Toner Cartridge Online
Type=Application
Exec=/opt/$VENDOR/mfp/bin/start_web_browser.sh $URL_SUPPLIERS
Path=/opt/$VENDOR/mfp/bin
Icon=/opt/$VENDOR/mfp/share/images/TonerReorder.png
Terminal=0
TerminalOptions=
X-KDE-SubstituteUID=false
X-KDE-Username=
EOF

fix_desktop_file_ownership $1
create_script_start_web_browser
}

write_helpviewer_desktop_file() {
if test -z "$1" ; then
return 1
fi
cat > $1 <<EOF
[Desktop Entry]
Name=$VENDOR Unified Driver Help
Name[C]=$VENDOR Unified Driver Help
Comment=HTML help viewer utility
Comment[C]=HTML help viewer utility
Type=Application
Exec=/opt/$VENDOR/mfp/bin/shhv
Path=/opt/$VENDOR/mfp/bin
Icon=/opt/$VENDOR/mfp/share/images/HelpViewer.png
Terminal=0
TerminalOptions=
X-KDE-SubstituteUID=false
X-KDE-Username=
EOF
}

write_uninstall_desktop_file() {
if test -z "$1" ; then
return 1
fi
cat > $1 <<EOF
[Desktop Entry]
Name=Uninstall $VENDOR Unified Driver
Name[C]=Uninstall $VENDOR Unified Driver
Comment=$VENDOR Unified Driver uninstallation script
Comment[C]=$VENDOR Unified Driver uninstallation script
Type=Application
Exec=/opt/$VENDOR/mfp/uninstall/uninstall.sh
Path=/opt/$VENDOR/mfp/uninstall
Icon=/opt/$VENDOR/mfp/share/images/Uninstall.png
Terminal=0
TerminalOptions=
X-KDE-SubstituteUID=false
X-KDE-Username=
EOF
}

append_categories() {
if test -n "$1" ; then
if echo "$LINUX_DIST" | grep -q "FEDORA_7_AND_ABOVE" ; then
echo "Categories=Application;SystemSetup;X-${VENDOR}-Config-UD;KDE;Core;" >> $1
else
echo "Categories=Application;SystemSetup;X-${VENDOR}-Config-UD;" >> $1
fi
fi
}

handle_menu() {
if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
if [ -d "$1" ] && mkdir -p "$1/${VENDOR}_UD" ; then
write_desktop_directory         $1/${VENDOR}_UD/.directory
write_configurator_desktop_file $1/${VENDOR}_UD/${VENDOR}Configurator.desktop
write_helpviewer_desktop_file   $1/${VENDOR}_UD/${VENDOR}HelpViewer.desktop
write_uninstall_desktop_file    $1/${VENDOR}_UD/${VENDOR}UninstallUD.desktop
fi
elif [ "$SCRIPT_MODE" = "UNINSTALL" ] ; then
rm -rf $1/${VENDOR}_UD
fi
}

handle_menu_redhat89() {
if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
if ! grep -q "$VENDOR Unified Driver" /etc/X11/desktop-menus/applications.menu ; then
${HARDWARE_PLATFORM}/install/vendormenu /etc/X11/desktop-menus/applications.menu
fi
write_desktop_directory         $2/${VENDOR}_UD.directory
write_configurator_desktop_file $1/${VENDOR}ConfiguratorUD.desktop
append_categories               $1/${VENDOR}ConfiguratorUD.desktop
write_helpviewer_desktop_file   $1/${VENDOR}HelpViewerUD.desktop
append_categories               $1/${VENDOR}HelpViewerUD.desktop
write_uninstall_desktop_file    $1/${VENDOR}UninstallUD.desktop
append_categories               $1/${VENDOR}UninstallUD.desktop
elif [ "$SCRIPT_MODE" = "UNINSTALL" ] ; then
rm -f $1/.directory \
$2/${VENDOR}_UD.directory \
$1/${VENDOR}ConfiguratorUD.desktop \
$1/${VENDOR}HelpViewerUD.desktop \
$1/${VENDOR}UninstallUD.desktop
fi
}

handle_menu_freedesktop() {
if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
if ! grep -q "$VENDOR Unified Driver" "$3" ; then
${HARDWARE_PLATFORM}/install/vendormenu -f $3
fi
write_desktop_directory         $2/${VENDOR}_UD.directory
write_configurator_desktop_file $1/${VENDOR}ConfiguratorUD.desktop
append_categories               $1/${VENDOR}ConfiguratorUD.desktop
write_helpviewer_desktop_file   $1/${VENDOR}HelpViewerUD.desktop
append_categories               $1/${VENDOR}HelpViewerUD.desktop
write_uninstall_desktop_file    $1/${VENDOR}UninstallUD.desktop
append_categories               $1/${VENDOR}UninstallUD.desktop
elif [ "$SCRIPT_MODE" = "UNINSTALL" ] ; then
rm -f $2/${VENDOR}_UD.directory \
$1/${VENDOR}ConfiguratorUD.desktop \
$1/${VENDOR}HelpViewerUD.desktop \
$1/${VENDOR}UninstallUD.desktop
fi
}

write_directory_for_update_menus() {
echo "?package(menu): charset=\"utf8\" section=\"/\" needs=\"x11\" title=\"$VENDOR Unified Driver\" icon=\"/opt/$VENDOR/mfp/share/images/Configurator.png\"" >> $1
}

write_entry_for_update_menus() {
echo "?package(menu): charset=\"utf8\" command=\"$1\" section=\"$VENDOR Unified Driver/\" needs=\"x11\" title=\"$2\" icon=\"$3\"" >> $4
}

handle_menu_with_xdg_desktop_menu() {
write_desktop_directory         /tmp/${VENDOR}-UD.directory
write_configurator_desktop_file /tmp/${VENDOR}-Configurator.desktop
write_helpviewer_desktop_file   /tmp/${VENDOR}-HelpViewer.desktop
write_uninstall_desktop_file    /tmp/${VENDOR}-UninstallUD.desktop

if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
DESKTOP_MENU_MODE=install
else
DESKTOP_MENU_MODE=uninstall
fi

xdg-desktop-menu $DESKTOP_MENU_MODE \
/tmp/${VENDOR}-UD.directory \
/tmp/${VENDOR}-Configurator.desktop \
/tmp/${VENDOR}-HelpViewer.desktop \
/tmp/${VENDOR}-UninstallUD.desktop

rm -f \
/tmp/${VENDOR}-UD.directory \
/tmp/${VENDOR}-Configurator.desktop \
/tmp/${VENDOR}-HelpViewer.desktop \
/tmp/${VENDOR}-UninstallUD.desktop

if [ "$SCRIPT_MODE" = "INSTALL" ] ; then

# Workaround for xdg-desktop-menu on Fedora 7 and 8.
# If xdg-desktop-menu is running from KDE desktop,
# it does not create menu file for GNOME !

if \
  test -f /etc/kde/xdg/menus/applications-merged/${VENDOR}-UD.menu && \
  test -d /etc/xdg/menus/applications-merged && \
! test -f /etc/xdg/menus/applications-merged/${VENDOR}-UD.menu ; then
cp -aL /etc/kde/xdg/menus/applications-merged/${VENDOR}-UD.menu \
/etc/xdg/menus/applications-merged/
fi
else
# It does not remove menu files on uninstall too
rm -f /etc/kde/xdg/menus/applications-merged/${VENDOR}-UD.menu \
/etc/xdg/menus/applications-merged/${VENDOR}-UD.menu
fi
}

handle_menu_with_update_menus() {

ENTRY_DIR=/usr/lib/menu
PACKAGE_STRING="$VENDOR Unified Driver"

rm -f $ENTRY_DIR/${VENDOR}_UD

if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
write_directory_for_update_menus $ENTRY_DIR/${VENDOR}_UD

write_entry_for_update_menus \
/opt/$VENDOR/mfp/bin/Configurator \
"$PACKAGE_STRING Configurator" \
/opt/$VENDOR/mfp/share/images/Configurator.png \
$ENTRY_DIR/${VENDOR}_UD

write_entry_for_update_menus \
/opt/$VENDOR/mfp/bin/shhv \
"$PACKAGE_STRING Help" \
/opt/$VENDOR/mfp/share/images/HelpViewer.png \
$ENTRY_DIR/${VENDOR}_UD

write_entry_for_update_menus \
/opt/$VENDOR/mfp/uninstall/uninstall.sh \
"Uninstall $PACKAGE_STRING" \
/opt/$VENDOR/mfp/share/images/Uninstall.png \
$ENTRY_DIR/${VENDOR}_UD
fi
}

create_dir_if_does_not_exist() {
if ! test -d "$1" ; then
mkdir -p $1
if test -n "$2" ; then
chmod $2 $1
fi
if test -n "$3" ; then
chown $3 $1
fi
fi
}

create_file_smfp_users_to_add() {
UID_USER_LIST=`cat /etc/passwd | awk -F ':' '{print  $3, $1}'`
rm -f /tmp/smfp_users_to_add
NONPRIVILEGED_USERS_LIST=
NONPRIVILEGED_USER_FOUND=0
ITEM_IS_UID=1
for item in $UID_USER_LIST ; do
if test "$ITEM_IS_UID" = "1" ; then
if test "`expr $item \> 499`" = "1" ; then
NONPRIVILEGED_USER_FOUND=1
fi
ITEM_IS_UID=0
else
if test "$NONPRIVILEGED_USER_FOUND" = "1" ; then
if ! cat /etc/group | grep ^$PRINTER_GROUP: | grep -qw $item ; then
echo -n " $item" >> /tmp/smfp_users_to_add
fi
NONPRIVILEGED_USER_FOUND=0
fi
ITEM_IS_UID=1
fi
done
}

create_kde_and_gnome_desktop_dirs_if_not_exist() {
OWNER_ID=`ls -ldn $1 2> /dev/null | awk '{print $3}'`
if [ "$OWNER_ID" = "0" ]; then
OWNER_ID=65534
fi
if test -d $1 && test "`expr $OWNER_ID \> 499`" = "1" ; then
OWNER_NAME=`ls -ld $1 | awk '{print $3}'`
create_dir_if_does_not_exist $1/Desktop        700 $OWNER_NAME
create_dir_if_does_not_exist $1/.gnome-desktop 700 $OWNER_NAME
fi
}

process_desktop_files() {

DESKTOP_NAMES='Desktop Desktop2 KDesktop .gnome-desktop'
for USER_HOME in `awk -F ':' '{print $6}' /etc/passwd` ; do
create_kde_and_gnome_desktop_dirs_if_not_exist $USER_HOME
for DESKTOP_SUBDIR in $DESKTOP_NAMES ; do
if [ -d $USER_HOME/$DESKTOP_SUBDIR ]; then
if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
write_configurator_desktop_file \
$USER_HOME/$DESKTOP_SUBDIR/${VENDOR}Configurator.desktop
write_toner_reorder_desktop_file \
$USER_HOME/$DESKTOP_SUBDIR/${VENDOR}TonerReorder.desktop
elif [ "$SCRIPT_MODE" = "UNINSTALL" ] ; then
rm -f $USER_HOME/$DESKTOP_SUBDIR/${VENDOR}Configurator.desktop
rm -f $USER_HOME/$DESKTOP_SUBDIR/${VENDOR}TonerReorder.desktop
fi
fi
done
done
}

process_desktop_menus() {

if test -n "`which xdg-desktop-menu 2> /dev/null`" ; then
handle_menu_with_xdg_desktop_menu
return
fi

if test -n "`which update-menus 2> /dev/null`" && ! echo "$LINUX_DIST" | grep -q "MANDRIVA_2007_AND_ABOVE" ; then
handle_menu_with_update_menus
update-menus
return
fi

if echo "$LINUX_DIST" | grep -q "UBUNTU\|MANDRIVA_2007_AND_ABOVE\|FEDORA_7_AND_ABOVE" ; then
# Freedesktop.org Menu ( Both GNOME and KDE )
if test -f /etc/xdg/menus/applications.menu ; then
DIR_FILES_LOCATION=/usr/share/desktop-menu-files
if test -d /usr/share/desktop-directories ; then
DIR_FILES_LOCATION=/usr/share/desktop-directories
fi
handle_menu_freedesktop /usr/share/applications $DIR_FILES_LOCATION /etc/xdg/menus/applications.menu
return
fi
fi

# GNOME Menu
if test -d /usr/share/gnome/apps ; then
handle_menu /usr/share/gnome/apps
elif test -d /etc/X11/applnk ; then
handle_menu /etc/X11/applnk
fi

# KDE Menu
if test -f /etc/X11/desktop-menus/applications.menu ; then
handle_menu_redhat89 /usr/share/applications /usr/share/desktop-menu-files
elif test -d /etc/opt/kde*/share/applnk/SuSE ; then
handle_menu /etc/opt/kde*/share/applnk/SuSE
elif test -d /opt/kde*/share/applnk ; then
handle_menu /opt/kde*/share/applnk
elif test -d /usr/share/applnk ; then
if test -d /usr/share/applnk-mdk ; then
handle_menu /usr/share/applnk-mdk
if test -d /var/lib/gnome/Mandrake ; then
handle_menu /var/lib/gnome/Mandrake
fi
else
if ! test -d /etc/X11/applnk ; then
# if no entries installed in /etc/X11/applnk only
# This condition resolves duplicated menu
# entries in Fedora 3,4
handle_menu /usr/share/applnk
elif `cat /etc/issue | grep -q 'Fedora Core release [5-9]' 2> /dev/null` ; then
# ... but in Fedora 5 (and above ?) we need these entries again
handle_menu /usr/share/applnk
fi
fi
fi
}

process_psu_and_smart_panel() {
if [ "$SCRIPT_MODE" = "INSTALL" ] ; then
if [ -e ./psu/install.sh ]; then
./psu/install.sh $VENDOR
fi
if [ -e ./smartpanel/install.sh ]; then
./smartpanel/install.sh $VENDOR
fi
elif [ "$SCRIPT_MODE" = "UNINSTALL" ] ; then
if [ -e /opt/${VENDOR}/PSU/uninstall.sh ]; then
/opt/${VENDOR}/PSU/uninstall.sh $VENDOR
fi
if [ -e /opt/${VENDOR}/SmartPanel/uninstall.sh ]; then
/opt/${VENDOR}/SmartPanel/uninstall.sh $VENDOR
fi
fi
}

### Install procedures

set_parport_pc_parameters() {
# Add options for parport_pc module if someone did not it before

if [ "$PLSFX" = "64" -a "$LINUX_DIST" = "SUSE_92" ]; then
OPT_LINE="options parport_pc io=0x378 irq=7 dma=none"
else
OPT_LINE="options parport_pc io=0x378 irq=7 dma=3"
fi
if ( uname -r | grep -q '^2\.[6-9]\|^[3-9]' ) ; then
if [ "$LINUX_DIST" = "SUSE_91" ] ; then
MOD_CONFIG_FILE=modprobe.conf.local
else
MOD_CONFIG_FILE=modprobe.conf
fi
else
MOD_CONFIG_FILE=modules.conf
fi
if ! ( cat /etc/$MOD_CONFIG_FILE | grep -q "$OPT_LINE" ) ; then
echo "$OPT_LINE" >> /etc/$MOD_CONFIG_FILE
echo "$OPT_LINE" > /etc/mfpcommon.modules.conf
fi

if test -f /etc/dynamic/scripts/lp.script ; then
shell_script_execution_disable /etc/dynamic/scripts/lp.script
fi
}

restart_cups() {
if   test -e /etc/init.d/cups ; then
CUPS_SCRIPT=/etc/init.d/cups
elif test -e /etc/init.d/cupsys ; then
CUPS_SCRIPT=/etc/init.d/cupsys
else
echo "INFO: can't restart CUPS - script not found"
wait_to_allow_to_see_info_line
return
fi

if $CUPS_SCRIPT restart ; then
echo "INFO: CUPS restart OK"
else
echo "INFO: CUPS restart FAILED"
fi
wait_to_allow_to_see_info_line
}

register_cups_printer() {

# Copy 64-bit filters to fix 64-bit only CUPS installation
if file /usr/lib/cups/filter/pstops 2> /dev/null | grep -qi 'ELF 64-bit' ; then
cp -af /usr/lib64/cups/filter/libscms*         /usr/lib/cups/filter/
cp -af /usr/lib64/cups/filter/pscms            /usr/lib/cups/filter/
cp -af /usr/lib64/cups/filter/rastertosamsung* /usr/lib/cups/filter/
cp -af /usr/lib64/cups/filter/smfpautoconf     /usr/lib/cups/filter/
cp -af /usr/lib64/cups/backend/mfp             /usr/lib/cups/backend/
fi

mkdir -p /usr/share/cups/model/${VENDOR_LC}/cms
cp -a /opt/${VENDOR}/mfp/share/ppd/cms/* /usr/share/cups/model/${VENDOR_LC}/cms/
chmod 444 /usr/share/cups/model/${VENDOR_LC}/cms/*
for MODNAME in $MODEL_LIST ; do
cat /opt/${VENDOR}/mfp/share/ppd/${MODNAME}.ppd | \
gzip -9 > /usr/share/cups/model/${VENDOR_LC}/${MODNAME}.ppd.gz
chmod 444 /usr/share/cups/model/${VENDOR_LC}/${MODNAME}.ppd.gz
done
if test -d /usr/share/ppd ; then
if test -h /usr/share/ppd/${VENDOR_LC} ; then
# Check symlink first, change it if exist
rm -f /usr/share/ppd/${VENDOR_LC}
ln -s /usr/share/cups/model/${VENDOR_LC} /usr/share/ppd/
elif test -d /usr/share/ppd/${VENDOR_LC} ; then
# Copy files into existing directory
cp -a /usr/share/cups/model/${VENDOR_LC}/*.ppd.* /usr/share/ppd/${VENDOR_LC}/
else
# Create symlink
rm -f /usr/share/ppd/${VENDOR_LC}
ln -s /usr/share/cups/model/${VENDOR_LC} /usr/share/ppd/
fi
fi

restart_cups

if test "$IN_TEXTMODE" = "1" || ! $MFP_INSTALL_DIR/bin/printeradd 2> /dev/null ; then
set_firmware_device_name
if test -n "$FIRMWARE_DEVICE_NAME" ; then
DEVICE_LINE=`/usr/lib${PLSFX}/cups/backend/mfp 2>/dev/null | grep "$FIRMWARE_DEVICE_NAME" | head -n 1`
else
DEVICE_LINE=
fi
if test -n "$DEVICE_LINE" ; then
DEVICE_PORT=`echo $DEVICE_LINE | awk '{print $2}'`
else
DEVICE_PORT="mfp:/dev/mfp4"
fi
lpadmin   -p $MODEL -m ${VENDOR_LC}/$MODEL.ppd.gz -v $DEVICE_PORT
lpadmin   -p $MODEL -E
lpadmin   -d $MODEL
lpoptions -x $MODEL > /dev/null 2>&1
lpoptions -d $MODEL > /dev/null 2>&1
fi
}

register_sane_backend() {

for SCDIR in /etc/sane.d /usr/local/etc/sane.d ; do
if [ -w ${SCDIR}/dll.conf ] ; then
if ! grep -q '^smfp$' ${SCDIR}/dll.conf ; then
echo "smfp" >> ${SCDIR}/dll.conf
fi
if grep -q geniusvp2 ${SCDIR}/dll.conf ; then
# Comment out geniusvp2 backend
cat ${SCDIR}/dll.conf > /tmp/mfp_dll_conf.tmp
cat /tmp/mfp_dll_conf.tmp | sed 's/geniusvp2/#geniusvp2/' > ${SCDIR}/dll.conf
rm -f /tmp/mfp_dll_conf.tmp
fi
chmod 664 ${SCDIR}/dll.conf
fi
done
# Create dll.conf if it does not exist
DLL_CONFS=`ls /etc/sane.d/dll.conf /usr/local/etc/sane.d/dll.conf 2> /dev/null`
if test -z "$DLL_CONFS" ; then
echo "smfp" >> /etc/sane.d/dll.conf
fi
}

save_configuration_files() {
TEMP_CONFIG_DIR="/tmp/mfp_${VENDOR}_install"
mkdir -p $TEMP_CONFIG_DIR || abort_execution "Can not create directory $TEMP_CONFIG_DIR"
if test -f $MFP_INSTALL_DIR/share/OEM.ini; then
cp -a -f $MFP_INSTALL_DIR/share/OEM.ini $TEMP_CONFIG_DIR/
else
touch $TEMP_CONFIG_DIR/OEM.ini
fi
if test -f /etc/sane.d/smfp.conf; then
cp -a -f /etc/sane.d/smfp.conf $TEMP_CONFIG_DIR/
fi
}

merge_configuration_files() {
test -d "$TEMP_CONFIG_DIR" || return 0

# Merge OEM.ini

FSRC=$TEMP_CONFIG_DIR/OEM.ini
FDST=$MFP_INSTALL_DIR/share/OEM.ini

# Set SCANNER to 1 if is is 1 in SRC or DST
if cat $FDST 2> /dev/null | grep -q 'SCANNER=0' ; then
if cat $FSRC 2> /dev/null | grep -q 'SCANNER=1' ; then
cat $FDST | sed 's/SCANNER=0/SCANNER=1/' > $TEMP_CONFIG_DIR/sed_output.tmp
cat $TEMP_CONFIG_DIR/sed_output.tmp > $FDST
fi
fi

#x# # Add model from SRC if it does not exist in DST
#x# cat $FSRC 2> /dev/null | while read t ; do
#x# if echo "$t" | grep -q 'MODEL' ; then
#x# if ! cat $FDST 2> /dev/null | grep -q "$t" ; then
#x# echo "$t" >> $FDST
#x# fi
#x# fi
#x# done

cp -a -f $FDST $MFP_INSTALL_DIR/uninstall/OEM.ini

# Merge smfp.conf
FDSTS=$TEMP_CONFIG_DIR/smfp.conf
if test -f $FDSTS; then
FSRCS=noarch/at_root/etc/sane.d/smfp.conf
chmod 644 $FDSTS
${HARDWARE_PLATFORM}/install/vendormenu -sm $FDSTS $FSRCS
cp -a -f $FDSTS /etc/sane.d/smfp.conf
fi

rm -f $TEMP_CONFIG_DIR/*
rmdir $TEMP_CONFIG_DIR
}

write_udev_rules_file() {
SUBNAME=$1
RULES_FILE=$2

echo '# This file is a part of Unified Linux Driver'                  > $RULES_FILE
echo '# Rules to allow low level USB device access for smfpautoconf' >> $RULES_FILE
echo ''                                                              >> $RULES_FILE
echo "SUBSYSTEM!=\"$SUBNAME\", GOTO=\"label_end\""                   >> $RULES_FILE
echo 'ACTION!="add", GOTO="label_end"'                               >> $RULES_FILE
echo ''                                                              >> $RULES_FILE
echo 'ATTRS{idVendor}=="0419", MODE="0666"'                          >> $RULES_FILE
echo 'ATTRS{idVendor}=="04e8", MODE="0666"'                          >> $RULES_FILE
echo 'ATTRS{idVendor}=="0924", MODE="0666"'                          >> $RULES_FILE
echo 'ATTRS{idVendor}=="413c", MODE="0666"'                          >> $RULES_FILE
echo ''                                                              >> $RULES_FILE
echo 'LABEL="label_end"'                                             >> $RULES_FILE

chown root:root $RULES_FILE
chmod 644       $RULES_FILE
}

write_cups_type_files() {

echo "application/vnd.cups-postscript application/vnd.samsung-spl 100 rastertosamsungspl"    > /etc/cups/smfp.convs
echo "application/vnd.cups-postscript application/vnd.samsung-splc 100 rastertosamsungsplc" >> /etc/cups/smfp.convs
echo "application/vnd.samsung-spl"  > /etc/cups/smfp.types
echo "application/vnd.samsung-splc" >> /etc/cups/smfp.types

chown root:root /etc/cups/smfp.convs /etc/cups/smfp.types
chmod 644       /etc/cups/smfp.convs /etc/cups/smfp.types
}

unwrap_setuid_ooo_application() {
WRAPPING_BIN=`ls /usr/lib*/*/program/$1.bin /opt/*/program/$1.bin 2> /dev/null | head -1`
if test -n "$WRAPPING_BIN" ; then
unwrap_setuid_third_party_application $WRAPPING_BIN
fi
}

symlink_sane_backend_and_mfpport_libraries() {
( cd /usr/lib$1 && \
rm -f libmfp.so libmfp.so.1 libmfpdetect.so libmfpdetect.so.1 ; \
ln -s -f libmfp.so.1.0.1 libmfp.so.1 ; true ln -s -f libmfpdetect.so.1.0.1 libmfpdetect.so.1 ; \
ln -s -f libmfp.so.1 libmfp.so ; true ln -s -f libmfpdetect.so.1 libmfpdetect.so )
( cd /usr/lib$1/sane && \
rm -f libsane-smfp.so libsane-smfp.so.1 ; \
ln -s -f libsane-smfp.so.1.0.1 libsane-smfp.so.1 ; \
ln -s -f libsane-smfp.so.1 libsane-smfp.so )
}

init_d_dependency_remove() {
if test -s $1 ; then
if grep -q 'smfpd' $1 ; then
cat $1 | sed -e 's/ smfpd//g' | grep -v '^smfpd:' > /tmp/depend.tmp
if test -s /tmp/depend.tmp ; then
cat /tmp/depend.tmp > $1
fi
rm -f /tmp/depend.tmp
fi
fi
}

init_d_dependency_add() {
init_d_dependency_remove $1
if test -s $1 ; then
cat $1 | sed -e 's/TARGETS =/TARGETS = smfpd/' > /tmp/depend.tmp
echo 'smfpd: cups' >> /tmp/depend.tmp
if test -s /tmp/depend.tmp ; then
cat /tmp/depend.tmp > $1
fi
rm -f /tmp/depend.tmp
fi
}

install_smfpd() {

if cp -a noarch/smfpd.sh /etc/init.d/smfpd ; then
chown root:root /etc/init.d/smfpd
chmod 755 /etc/init.d/smfpd

RC_D_PREFIX=
for d in /etc /etc/rc.d /etc/init.d ; do
if ! test -h $d ; then
if ! test -h $d/rc0.d ; then
if test -d $d/rc0.d ; then
RC_D_PREFIX=$d
fi
fi
fi
done
if test -n "$RC_D_PREFIX"; then
LN_PREFIX=..
if ! test -f $RC_D_PREFIX/rc0.d/$LN_PREFIX/smfpd ; then
LN_PREFIX=../init.d
if ! test -f $RC_D_PREFIX/rc0.d/$LN_PREFIX/smfpd ; then
echo "ERROR: link into init.d directory failed"
fi
fi
for n in 0 1 6 ; do
( cd $RC_D_PREFIX/rc${n}.d && ln -s $LN_PREFIX/smfpd ./K07smfpd )
done
for n in 2 3 4 5 ; do
( cd $RC_D_PREFIX/rc${n}.d && ln -s $LN_PREFIX/smfpd ./S93smfpd )
done
else
echo "ERROR: rc0.d directory not found"
fi
init_d_dependency_add /etc/init.d/.depend.start
init_d_dependency_add /etc/init.d/.depend.stop
/etc/init.d/smfpd start > /dev/null
else
echo "ERROR: can not copy smfpd startup script to /etc/init.d/"
fi

chown root:root /usr/sbin/smfpd
chmod 755 /usr/sbin/smfpd
}

modify_printer_group_member_list() {
if test -f /tmp/smfp_users_to_add ; then
echo "INFO: Adding users to $PRINTER_GROUP group ..."
for u in `cat /tmp/smfp_users_to_add 2> /dev/null` ; do
G_LIST=`cat /etc/group | grep -w "$u" | grep -wv "^$u" | awk -F : '{print $1}' | grep -wv ^$PRINTER_GROUP`
if test -n "$G_LIST" ; then
usermod -G `echo $G_LIST | sed s/\ /,/g`,$PRINTER_GROUP $u
else
usermod -G $PRINTER_GROUP $u
fi
done
wait_to_allow_to_see_info_line
fi
if test -f /tmp/smfp_users_to_remove ; then
echo "INFO: Removing users from printer group ..."
for u in `cat /tmp/smfp_users_to_remove 2> /dev/null` ; do
G_LIST=`cat /etc/group | grep -w "$u" | grep -wv "^$u" | awk -F : '{print $1}' | grep -wv ^$PRINTER_GROUP`
if test -n "$G_LIST" ; then
usermod -G `echo $G_LIST | sed s/\ /,/g` $u
else
usermod -G "" $u
fi
done
wait_to_allow_to_see_info_line
fi
}

application_resource_cleanup() {
UID_USER_LIST=`cat /etc/passwd | awk -F ':' '{print  $3, $4, $1, $6}'`
ITEM_INDEX=0
for item in $UID_USER_LIST ; do
if test "$ITEM_INDEX" = "0" ; then
LAST_UID=$item
ITEM_INDEX=1
elif test "$ITEM_INDEX" = "1" ; then
LAST_GID=$item
ITEM_INDEX=2
elif test "$ITEM_INDEX" = "2" ; then
LAST_LOGIN=$item
ITEM_INDEX=3
else
# Item is Home Directory
if test -d $item/.qt ; then
chown $LAST_UID:$LAST_GID $item/.qt
rm -f $item/.qt/scanconfrc $item/.qt/image_editorrc
fi
ITEM_INDEX=0
fi
done
}

restart_udev() {
echo "INFO: Restarting udev ..."

if udevadm help 2>/dev/null; then
udevadm control --reload_rules
udevadm trigger
elif udevtrigger --help 2>/dev/null; then
udevcontrol reload_rules
udevtrigger
elif test -f /etc/init.d/udev ; then
/etc/init.d/udev restart
else
echo "ERROR: Failure to restart udev"
fi
}

restart_nautilus_if_running() {
NAUTILUS_USER=`ps auxw | grep nautilus | grep -v grep | awk '{print $1}' | head -1`

if [ -n "$NAUTILUS_USER" ]; then
NAUTILUS_VERSION=`nautilus --version 2> /dev/null | awk '{print $3}' | sed 's/\.//g'`
if [ "$NAUTILUS_VERSION" -ge 2262 ]; then
sudo -u "$NAUTILUS_USER" nautilus -q > /dev/null 2>&1
sudo -u "$NAUTILUS_USER" nautilus -n > /dev/null 2>&1 &
fi

fi
}

# Main installation procedure

do_install() {

SCRIPT_MODE=INSTALL

if [ "$THIS_PACKAGE_ALREADY_INSTALLED" = "0" ]; then
rm -rf /opt/$VENDOR/mfp
INCREMENT_MODE=0
else
save_configuration_files
INCREMENT_MODE=1
fi

# Install common files begin {
copy_base_files

if [ "$QT_MODE" = "$QT_MODE_QT_SUPPLIED" ]; then
# Make native qtrc accessible for custom libqt too
NATIVE_QTRC=`ls /usr/lib*/qt*/etc/settings/qtrc /etc/qtrc 2> /dev/null | head -1`
if test -n "$NATIVE_QTRC"; then
mkdir -p /etc/qt-smfp
rm -f /etc/qt-smfp/qtrc
ln -s -f $NATIVE_QTRC /etc/qt-smfp/qtrc
fi
fi

# Install OEM.ini
cp -a -f OEM.ini $MFP_INSTALL_DIR/share/OEM.ini
cp -a -f OEM.ini $MFP_INSTALL_DIR/uninstall/OEM.ini

merge_configuration_files
write_udev_rules_file usb_device /etc/udev/rules.d/98_smfpautoconf_samsung.rules
write_udev_rules_file usb        /etc/udev/rules.d/99_smfpautoconf_samsung.rules
write_cups_type_files

wait_to_allow_to_see_info_line

restart_udev

echo "INFO: Installing MFP port and SANE backend libraries ..."
symlink_sane_backend_and_mfpport_libraries ${PLSFX}

if [ "${PLSFX}" = "64" ]; then
# Install 32-bit SANE backend on 64-bit platform if possible
LIBSANE_FILES=`ls /usr/lib/libsane.so.1.*.* /usr/lib64/libsane.so.1.*.* 2> /dev/null`
LIBSANE_FILES_TOTAL=`echo $LIBSANE_FILES | wc | awk '{print $2}'`
# If two libsane.so.1.x.x files in lib and lib64 exist ...
if [ "$LIBSANE_FILES_TOTAL" = "2" ]; then
# ... and they differ
if ! diff $LIBSANE_FILES 1> /dev/null 2> /dev/null ; then
# then install 32-bit sane backend also
LIBSTDCXX_FILES=`ls /usr/lib/libstdc++.so.5* 2> /dev/null`
LIBSTDCXX_ARC="noarch/libstdc++-5-i386.tar.gz"
if test -z "$LIBSTDCXX_FILES" -a -f $LIBSTDCXX_ARC ; then
zcat $LIBSTDCXX_ARC | tar -xf - -C / 2> /dev/null
fi
copy_directories "i386/at_root" /
symlink_sane_backend_and_mfpport_libraries
fi
fi
fi
wait_to_allow_to_see_info_line

# Install common files end   }

if [ "$PARPORT" = "1" ] ; then
install_smfpd
fi

set_parport_pc_parameters

# Substitute CUPS lpr with slpr begin {

echo "INFO: Installing GUI lpr ..."
# Save lpr.cups if it was not done before
if [ ! -f /usr/bin/lpr.cups.orig ]; then
if [ -f /usr/bin/lpr.cups ]; then
cp -a -f /usr/bin/lpr.cups /usr/bin/lpr.cups.orig
fi
fi

# Save lpr if it was not done before
if [ ! -f /usr/bin/lpr.orig ]; then
mv -f /usr/bin/lpr /usr/bin/lpr.orig 2> /dev/null || \
echo "ERROR: " "/usr/bin/lpr does not exist. Try reinstall CUPS" && sleep 5
# abort_execution "/usr/bin/lpr does not exist. Try reinstall CUPS"
else
rm -f /usr/bin/lpr
fi

ln -s $MFP_INSTALL_DIR/bin/slpr /usr/bin/lpr
wait_to_allow_to_see_info_line

echo "INFO: Fixing file ownership and permissions ..."
find $MFP_INSTALL_DIR -exec chown root:root \{\} \;
chown root:root /usr/lib${PLSFX}/cups/backend/mfp

chmod 755 /usr/lib${PLSFX}/cups/backend/mfp
chmod 755 $MFP_INSTALL_DIR/bin/slpr

# Create libcups.so symlink if it does not exist
( cd /usr/lib   && test -f libcups.so.2 && ! test -h libcups.so && ln -s libcups.so.2 libcups.so )
( cd /usr/lib64 && test -f libcups.so.2 && ! test -h libcups.so && ln -s libcups.so.2 libcups.so )

wait_to_allow_to_see_info_line

# Substitute CUPS lpr with slpr end   }

echo "INFO: Registering SANE backend ..."
if cat ./OEM.ini 2> /dev/null | grep -q 'SCANNER=1' ; then
register_sane_backend
fi
wait_to_allow_to_see_info_line
echo "INFO: Registering CUPS printer ..."
register_cups_printer
wait_to_allow_to_see_info_line

echo "INFO: Creating menu entries ..."
process_desktop_files
restart_nautilus_if_running
process_desktop_menus
process_psu_and_smart_panel

modify_printer_group_member_list
application_resource_cleanup

echo "INFO: Finishing installation ..."
wait_to_allow_to_see_info_line
}

### Uninstall procedures

unregister_cups_printers() {
# FIXME: check if CUPS running and run it if not

PPD_DIST=`ls /opt/${VENDOR}/mfp/share/ppd/*.ppd 2>/dev/null`
PPD_CUPS=`ls /etc/cups/ppd/*.ppd 2>/dev/null`

if test -z "$PPD_DIST" ; then
return
fi

PRINTERS_TO_UNINSTALL=""

for fn_cups in $PPD_CUPS ; do
MODEL_STRING_CUPS=`grep '*ModelName:' $fn_cups | awk -F\" '{print $2}'`
for fn_dist in $PPD_DIST ; do
MODEL_STRING_DIST=`grep '*ModelName:' $fn_dist | awk -F\" '{print $2}'`
if [ "$MODEL_STRING_CUPS" = "$MODEL_STRING_DIST" ]; then
PRINTERS_TO_UNINSTALL="$PRINTERS_TO_UNINSTALL `basename $fn_cups .ppd`"
fi
done
done

for printer_name in $PRINTERS_TO_UNINSTALL ; do
echo "INFO: Removing printer $printer_name ..."
lpadmin -x $printer_name 2> /dev/null || true
lpoptions -x $printer_name > /dev/null 2>&1 || true
wait_to_allow_to_see_info_line
done

# This will remove symlink, but will not remove directory
# which may contain third-party files
rm -f  /usr/share/ppd/${VENDOR_LC}
rm -rf /usr/share/cups/model/${VENDOR_LC}/cms

for MODNAME in $MODEL_LIST ; do
# lpadmin -x $MODNAME 2>/dev/null
rm -f /usr/share/cups/model/${VENDOR_LC}/${MODNAME}.ppd.gz
done

rmdir /usr/share/cups/model/${VENDOR_LC} 2> /dev/null || true
}

unregister_sane_backend() {

for SCDIR in /etc/sane.d /usr/local/etc/sane.d ; do
if [ -w ${SCDIR}/dll.conf ] ; then
cat ${SCDIR}/dll.conf | grep -v "smfp" | \
sed 's/geniusvp2/#geniusvp2/' > /tmp/mfp_dll_conf.tmp
cat /tmp/mfp_dll_conf.tmp > ${SCDIR}/dll.conf
rm -f /tmp/mfp_dll_conf.tmp
fi
done
}

restore_parport_pc_parameters() {

# Remove options of parport_pc module if we added them during install

if [ -f /etc/mfpcommon.modules.conf ] ; then
if [ "$PLSFX" = "64" -a "$LINUX_DIST" = "SUSE_92" ]; then
OPT_LINE="options parport_pc io=0x378 irq=7 dma=none"
else
OPT_LINE="options parport_pc io=0x378 irq=7 dma=3"
fi
if ( uname -r | grep -q '^2\.[6-9]\|^[3-9]' ) ; then
if [ "$LINUX_DIST" = "SUSE_91" ] ; then
MOD_CONFIG_FILE=modprobe.conf.local
else
MOD_CONFIG_FILE=modprobe.conf
fi
else
MOD_CONFIG_FILE=modules.conf
fi
if ( cat /etc/$MOD_CONFIG_FILE | grep -q "$OPT_LINE" ) ; then
cat /etc/$MOD_CONFIG_FILE | grep -v "$OPT_LINE" > /etc/mfpcommon.modules.conf
cat /etc/mfpcommon.modules.conf > /etc/$MOD_CONFIG_FILE
fi
rm -f /etc/mfpcommon.modules.conf
fi

if test -f /etc/dynamic/scripts/lp.script ; then
shell_script_execution_enable /etc/dynamic/scripts/lp.script
fi
}

uninstall_common_files() {

if test -f /usr/sbin/smfpd || test -f /etc/init.d/smfpd ; then
echo "INFO: Uninstalling smfpd daemon ..."
init_d_dependency_remove /etc/init.d/.depend.start
init_d_dependency_remove /etc/init.d/.depend.stop
/etc/init.d/smfpd stop > /dev/null
rm -f /etc/init.d/rc*.d/[KS][0-9][0-9]smfpd
rm -f /etc/rc*.d/[KS][0-9][0-9]smfpd
rm -f /etc/init.d/smfpd
rm -f /usr/sbin/smfpd
fi

echo "INFO: Restoring CUPS lpr ..."
rm -f /usr/bin/lpr
if [ -f /usr/bin/lpr.cups.orig ]; then
mv -f /usr/bin/lpr.cups.orig /usr/bin/lpr.cups
fi
if [ -f /usr/bin/lpr.orig ]; then
mv -f /usr/bin/lpr.orig /usr/bin/lpr
fi
wait_to_allow_to_see_info_line

echo "INFO: Unregistering SANE backend ..."
unregister_sane_backend
wait_to_allow_to_see_info_line

echo "INFO: Uninstalling common files ..."
rm -f  /usr/lib*/libmfp.so*
rm -f  /usr/lib*/libmfpdetect.so*
rm -f  /usr/lib*/cups/backend/mfp
rm -f  /usr/lib*/cups/filter/*sc.cts
rm -f  /usr/lib*/cups/filter/*sf.so
rm -f  /usr/lib*/cups/filter/libscms*
rm -f  /usr/lib*/cups/filter/pscms
rm -f  /usr/lib*/cups/filter/rastertosamsunginkjet
rm -f  /usr/lib*/cups/filter/rastertosamsungpcl
rm -f  /usr/lib*/cups/filter/rastertosamsungspl
rm -f  /usr/lib*/cups/filter/rastertosamsungsplc
rm -f  /usr/lib*/cups/filter/smfpautoconf
rm -f  /usr/lib*/sane/libsane-smfp.so*
rm -f  /etc/sane.d/smfp.conf
wait_to_allow_to_see_info_line

restore_parport_pc_parameters

# Restore original imagetoraster CUPS filter

if [ -f /usr/lib${PLSFX}/cups/filter/imagetoraster.cups ] ; then
mv -f /usr/lib${PLSFX}/cups/filter/imagetoraster.cups /usr/lib${PLSFX}/cups/filter/imagetoraster
fi

# Remove Help configuration files

rm -f /root/.shhvrc /root/.shhvfavs /home/*/.shhvrc /home/*/.shhvfavs

# Remove CUPS type files

rm -f /etc/cups/smfp.convs /etc/cups/smfp.types

# Remove udev rules

rm -f /etc/udev/rules.d/*_smfpautoconf_samsung.rules
restart_udev
}

unwrap_setuid_third_party_application() {
if echo "$1" | grep -q "/" ; then
APP_NAME=$1
else
APP_NAME=`which $1 2> /dev/null`
fi
NEW_NAME=${APP_NAME}.bin

if test -n "$APP_NAME" ; then
if test -f "$NEW_NAME" && ! test -d "$NEW_NAME"; then
rm -f "$APP_NAME"
mv "$NEW_NAME" "$APP_NAME"
fi
fi
}

#uninstall_legacy_files() {
# true
#}

uninstall_legacy_common_files() {
# Remove setuid wrappers which may be installed by
# Unified Linux Driver v. 2.0
unwrap_setuid_third_party_application xsane
unwrap_setuid_third_party_application xscanimage

unwrap_setuid_ooo_application soffice
unwrap_setuid_ooo_application swriter
unwrap_setuid_ooo_application simpress
unwrap_setuid_ooo_application scalc
}

uninstall_smfp_common() {
test -d /opt/smfp-common && ( cd /opt && rm -rf smfp-common )
}

# Main uninstall procedure

do_uninstall() {

SCRIPT_MODE=UNINSTALL

echo "INFO: Unregistering CUPS printer ..."
unregister_cups_printers
wait_to_allow_to_see_info_line

# uninstall_legacy_files

check_related_packages
if [ "$TOTAL_RELATED_PACKAGES_INSTALLED" = "1" ]; then
# The last from the group of related packages. Remove common files.
uninstall_legacy_common_files
uninstall_common_files
else
# Remove slpr to check if lpr would became broken link after uninstall
rm -f /opt/$VENDOR/mfp/bin/slpr
# Check if lpr is broken link
if ! test -x /usr/bin/lpr ; then
for SLPR_FILE in `ls -tr /opt/*/mfp/bin/slpr 2> /dev/null` ; do
if test -x $SLPR_FILE ; then
rm -f /usr/bin/lpr
ln -s -f $SLPR_FILE /usr/bin/lpr
fi
done
fi
fi

process_desktop_files
process_desktop_menus
process_psu_and_smart_panel

echo "INFO: Finishing uninstall ..."

if test -d /etc/qt-smfp ; then
rm -rf /etc/qt-smfp
fi

# Remove persistent settings created by QSettings
for f in $VENDOR_LC scanconf image_editor scfgtools ; do
rm -f /home/*/.qt/${f}rc /usr/lib*/qt*/etc/settings/${f}rc /etc/X11/${f}rc
rm -f /home/*/.qt/.${f}rc.* /usr/lib*/qt*/etc/settings/.${f}rc.* /etc/X11/.${f}rc.*
done

if [ "$TOTAL_RELATED_PACKAGES_INSTALLED" = "1" ]; then
uninstall_smfp_common
fi

test -n "$VENDOR" || abort_execution "VENDOR undefined"
exec /bin/sh -c "rm -rf /opt/$VENDOR/mfp 2> /dev/null && rmdir /opt/$VENDOR 2> /dev/null"

wait_to_allow_to_see_info_line
}

# Text mode procedures

ask_any_key_or_q() {
# read -p '****  Press any key to continue or q to quit: ' -n 1 KEY_PRESSED
read -p '****  Press Enter to continue or q and then Enter to quit: ' KEY_PRESSED
echo ""
if test "$KEY_PRESSED" = "q" || test "$KEY_PRESSED" = "Q" ; then
echo "****  $RUN_MODE terminated by user"
exit 0
fi
}


select_model_in_textmode() {
MODEL=
while test -z "$MODEL" ; do
if test -n "$MODEL_LIST" ; then
echo "****  Print drivers for the following device models available:"
echo $MODEL_LIST
read -p "****  Please enter model to install and press Enter: " KEY_PRESSED
if test -z "$KEY_PRESSED" ; then
MODEL=`echo $MODEL_LIST | awk '{print $1}'`
elif echo "$MODEL_LIST" | grep -qw "$KEY_PRESSED" ; then
MODEL=$KEY_PRESSED
else
echo "****"
echo "ERROR Invalid model entered. Please enter model from the list,"
echo "ERROR or press Enter to select the first one."
echo "****"
fi
fi
done
}

run_textmode_dialog() {

test "`id -u`" = "0" || abort_execution "Root priviliges required"

test -n "$VENDOR" || abort_execution "VENDOR undefined"
IN_TEXTMODE=1

if [ "$RUN_MODE" = "$RUN_MODE_UNINSTALL" ]; then
echo "****  Running text mode uninstall"
ask_any_key_or_q
do_uninstall
echo "****  Text mode uninstall finished"
else
echo "****  Running text mode install"
ask_any_key_or_q
create_file_smfp_users_to_add
if test -s /tmp/smfp_users_to_add ; then
echo "**** Non-priviliged users found:"
echo `cat /tmp/smfp_users_to_add`
echo "****  Are you going to use USB-connected devices ?"
echo "****  If yes, users allowed to scan or manage printers should be added to $PRINTER_GROUP"
echo "****  group. The list of non-privileged users proposed for addition is shown above."
read -p "****  Press y and then Enter to add users or Enter to leave $PRINTER_GROUP group intact: " KEY_PRESSED
echo ""
if test "$KEY_PRESSED" != "y" && test "$KEY_PRESSED" != "Y" ; then
rm -f /tmp/smfp_users_to_add
fi
fi
select_model_in_textmode
do_install
echo "****  Text mode install finished"
fi
}

print_message_qt_not_found() {
echo "****  It seems Qt library is not installed, or X display is not accessible."
echo "****  Custom Qt library will be configured for use with this package."
}

# Script execution starts here }

# test "$1" != "STAGE_GUI" && date > /tmp/install.log

SCRIPT_DIR=`dirname "$0"`
SCRIPT_NAME=`basename "$0"`
cd "$SCRIPT_DIR"

umask 022
set_variables

MODIFIER_ID_STRING="Inserted by Unified Linux Driver"

MODEL_LIST=`ls ./noarch/at_opt/share/ppd/*.ppd 2> /dev/null | awk -F. '{print $2}' | awk -F/ '{print $6}'`
if test -z "$MODEL_LIST" ; then
MODEL_LIST=`ls ../share/ppd/*.ppd 2> /dev/null | awk -F. '{print $3}' | awk -F/ '{print $4}'`
fi
# The first model in the list is default
# Default model will be used if printeradd is not succeeded
MODEL=`echo $MODEL_LIST | awk '{print $1}'`

test -n "$HARDWARE_PLATFORM" || abort_execution "HARDWARE_PLATFORM undefined"
if [ "$HARDWARE_PLATFORM" != "i386" -a "$HARDWARE_PLATFORM" != "x86_64" ]; then
abort_execution "Unsuppored hardware platform \"$HARDWARE_PLATFORM\""
fi

# GLIBC_VERSION_TWO_DIGITS=`ls /lib/ld-*.so 2> /dev/null | sed s:/lib/ld-:: | cut -b 1-3`
# if [ "$GLIBC_VERSION_TWO_DIGITS" = "2.2" ]; then
# HARDWARE_PLATFORM="i386-glibc22"
# fi

test -n "$VENDOR" || abort_execution "VENDOR undefined"
MFP_INSTALL_DIR=$INSTALL_DIR_MFP

ensure_proc_bus_usb_mounted

RUN_MODE_INSTALL=install
RUN_MODE_UNINSTALL=uninstall
RUN_MODE_CHECK=check
RUN_MODE_SHOW_VERSIONS=show_versions
RUN_MODE=$RUN_MODE_INSTALL
if [ "$SCRIPT_NAME" = "uninstall.sh" ]; then
RUN_MODE=$RUN_MODE_UNINSTALL
fi

RUN_STAGE_INITIAL=initial
RUN_STAGE_FROM_GUI=fromgui
RUN_STAGE=$RUN_STAGE_INITIAL

UI_MODE_GUI=gui
UI_MODE_TEXT=text
UI_MODE=$UI_MODE_GUI

QT_MODE_AUTO=auto
QT_MODE_QT3=qt3
QT_MODE_QT4=qt4
QT_MODE_QT_SUPPLIED=qt_supplied
QT_MODE=$QT_MODE_AUTO

SUBDIR_QT3=.
SUBDIR_QT4=qt4apps
SUBDIR_QT=$SUBDIR_QT3

RUN_FROM_DIST=dist
RUN_FROM_INSTALL=install
RUN_FROM=$RUN_FROM_DIST
if ! [ -d ./$HARDWARE_PLATFORM ]; then
RUN_FROM=$RUN_FROM_INSTALL
fi

PARPORT=1

while [ -n "$1" ]; do
case $1 in
STAGE_GUI) RUN_STAGE=$RUN_STAGE_FROM_GUI ;;
PARPORT=*) PARPORT=${1#PARPORT=} ;;
--run-mode=*) RUN_MODE=${1#--run-mode=} ;;
--ui-mode=*) UI_MODE=${1#--ui-mode=} ;;
--qt-mode=*) QT_MODE=${1#--qt-mode=} ;;
-i) RUN_MODE=$RUN_MODE_INSTALL ;;
-u) RUN_MODE=$RUN_MODE_UNINSTALL ;;
-t) UI_MODE=$UI_MODE_TEXT ;;
-ut) RUN_MODE=$RUN_MODE_UNINSTALL ; UI_MODE=$UI_MODE_TEXT ;;
-tu) RUN_MODE=$RUN_MODE_UNINSTALL ; UI_MODE=$UI_MODE_TEXT ;;
-c) RUN_MODE=$RUN_MODE_CHECK ;;
-v) RUN_MODE=$RUN_MODE_SHOW_VERSION ;;
*) echo "Invalid argument <$1>" ; exit 1 ;;
esac
shift
done

if [ "$RUN_MODE" = "$RUN_MODE_CHECK" ]; then
sh check_installation.sh ; exit 0
elif [ "$RUN_MODE" = "$RUN_MODE_SHOW_VERSION" ]; then
show_versions ; exit 0
fi

if [ "$RUN_FROM" = "$RUN_FROM_DIST" ]; then
DIST_DIR=`pwd`
fi

if [ "$QT_MODE" = "$QT_MODE_AUTO" ]; then
GUIEXEC_NAME=guiinstall
if [ "$RUN_MODE" = "$RUN_MODE_UNINSTALL" ]; then
GUIEXEC_NAME=guiuninstall
fi

if [ "$RUN_FROM" = "$RUN_FROM_DIST" ]; then
# launched from dist, suitable gui application (qt3/qt4) is selected
GUIEXEC_QT3="./$HARDWARE_PLATFORM/$SUBDIR_QT3/install/$GUIEXEC_NAME"
GUIEXEC_QT4="./$HARDWARE_PLATFORM/$SUBDIR_QT4/install/$GUIEXEC_NAME"
if "$GUIEXEC_QT4" --help > /dev/null 2>&1 ; then
QT_MODE=$QT_MODE_QT4
GUIEXEC=$GUIEXEC_QT4
SUBDIR_QT=$SUBDIR_QT4
elif "$GUIEXEC_QT3" --help > /dev/null 2>&1 ; then
QT_MODE=$QT_MODE_QT3
GUIEXEC=$GUIEXEC_QT3
SUBDIR_QT=$SUBDIR_QT3
else
QT_MODE=$QT_MODE_QT_SUPPLIED
GUIEXEC=$GUIEXEC_QT3
SUBDIR_QT=$SUBDIR_QT3
QT_SUPPLIED_DIR=$DIST_DIR/$HARDWARE_PLATFORM/lib$PLSFX
export LD_LIBRARY_PATH="$QT_SUPPLIED_DIR:$LD_LIBRARY_PATH"
fi
else
# launched from installation directory => uninstall mode
GUIEXEC="./$GUIEXEC_NAME"
fi
fi

if test -z "$MODEL" ; then
echo "WARNING: installation model undefined"
fi

if [ "$RUN_STAGE" = "$RUN_STAGE_INITIAL" ]; then
if [ "$RUN_MODE" = "$RUN_MODE_INSTALL" ]; then
check_icc_redist
check_libstdcxx
check_libtiff
if [ "$QT_MODE" = "$QT_MODE_QT_SUPPLIED" ]; then
print_message_qt_not_found
fi
fi

if [ "$UI_MODE" = "$UI_MODE_TEXT" ]; then
run_textmode_dialog
exit 0
fi

# $UI_MODE = $UI_MODE_GUI

if ! test -e "$GUIEXEC" ; then
echo "GUI mode installer not found, proceeding in text mode"
run_textmode_dialog
exit 0
fi

if ! $GUIEXEC --help > /dev/null 2>&1 ; then
echo "GUI mode installer execution failed, proceeding in text mode"
run_textmode_dialog
exit 0
fi

if [ "$RUN_MODE" = "$RUN_MODE_UNINSTALL" ]; then
P1=
P2=
P3=
P4=
P5=
P6=
if [ "$RUN_FROM" = "$RUN_FROM_DIST" ]; then
if [ "$QT_MODE" = "$QT_MODE_QT4" ] ; then
P1="--res=$DIST_DIR/noarch/at_opt/share/ui/guiuninstallui.rcc"
else
P1="--ui=$DIST_DIR/noarch/at_opt/share/ui/uninstalldialogbase.ui"
fi
fi
else
detect_system_packages
P1="--cups=$CUPS_DETECTED"
P2="--gs=$GS_DETECTED"
P3="--sane=$SANE_DETECTED"
P4="--printer-group=$PRINTER_GROUP"
P5="--qt-mode=$QT_MODE"
P6=
fi

# When launched from distribution area add distribution binary dir to the PATH. shhv may be run from guiinstall or guiuninstall.
if [ "$RUN_FROM" = "$RUN_FROM_DIST" ]; then
export PATH="$DIST_DIR/$HARDWARE_PLATFORM/$SUBDIR_QT/at_opt/bin:$PATH"
fi

$GUIEXEC $P1 $P2 $P3 $P4 $P5 $P6
# guiinstall or guiuninstall will run this script again with
# STAGE_GUI as the first parameter.
# You may think this script continues execution from
# the line 'GUI installer stage continues here' below.
exit
fi

# GUI installer stage continues here
if [ "$RUN_MODE" = "$RUN_MODE_UNINSTALL" ]; then
do_uninstall
exit 0
fi

# If not 'uninstall and exit' then do installation
do_install
exit 0


[heartsmagic]

Ağ yazıcısı yani? CUPS kurulu ve çalışıyor mu? Samba da lazımdır onun için sanırım.

[decent]

http://www.samsung.com/us/support/owners/product/SCX-4623F/XAA#drivers

bağlantısından Linux için sunulan üç dosyayı da yüklemen gerekiyor mu ?

[s.corpara]

http://www.samsung.com/us/support/owners/product/SCX-4623F/XAA#drivers

bağlantısından Linux için sunulan üç dosyayı da yüklemen gerekiyor mu ?

diğer 2 sini yüklemiştim daha önce yardımcı uygulamalar, yüklü durumdalar.

Ağ yazıcısı yani? CUPS kurulu ve çalışıyor mu? Samba da lazımdır onun için sanırım.

cups ve samba hakkında bir fikrim yok açıkcası

[heartsmagic]

Kod Seç Genişlet

dpkg -l | grep cups
ps aux | grep cups

ne diyor?

[s.corpara]

Kod Seç Genişlet

dpkg -l | grep cups
ps aux | grep cups

ne diyor?

hocam yüklediklerimi kaldırdım cups u kaldırdım, ve tekrar sırasıyla.

cups
UnifiedLinuxDriver_1.10.tar.gz
Smartpanel_1.10.tar.gz
PSU_1.10.tar.gz

kurdum, şu an sorun yok gibi duruyor,  ama yazdır dediğimde, kuyruğa alıyor yazdırmıyor.

yazıcılar kısmına girdim sürücüyle gelen yazıcının yanına, ekle - ağ yaızıcısı - samsung csx 4623 series i seçerek yeni yazıcı ekledim,
öntanımlı yaptım, sürücü kurarken eklenen yazıcıyı sildim ve bir sayfa gönderdim çıktı alabildim. Şimdi yeniden başlatıp deniycem oldu sanırsam

edit: yeniden başlattım ve sorun yok herkese çok çok teşekkürler

Kod Seç Genişlet


scorp@scorp:~$ dpkg -l | grep cups
ii  cups                                 1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - server
ii  cups-client                          1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - client programs (SysV)
ii  cups-common                          1.6.2-1ubuntu5                       all          Common UNIX Printing System(tm) - common files
ii  cups-daemon                          1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - daemon
ii  cups-filters                         1.0.34-0ubuntu1.1                    i386         OpenPrinting CUPS Filters
ii  cups-ppdc                            1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - PPD manipulation utilities
ii  ghostscript-cups                     9.07~dfsg2-0ubuntu3                  i386         interpreter for the PostScript language and for PDF - CUPS filters
ii  libcups2:i386                        1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - Core library
ii  libcupscgi1:i386                     1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - CGI library
ii  libcupsfilters1:i386                 1.0.34-0ubuntu1.1                    i386         OpenPrinting CUPS Filters - Shared library
ii  libcupsimage2:i386                   1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - Raster image library
ii  libcupsmime1:i386                    1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - MIME library
ii  libcupsppdc1:i386                    1.6.2-1ubuntu5                       i386         Common UNIX Printing System(tm) - PPD manipulation library
ii  python-cups                          1.9.62-0ubuntu3                      i386         Python bindings for CUPS
ii  python-cupshelpers                   1.3.12+20130308-0ubuntu4             all          Python modules for printer configuration with CUPS
scorp@scorp:~$ ps aux | grep cups
root       760  0.1  0.4   7924  3392 ?        Ss   13:11   0:00 /usr/sbin/cupsd -F
scorp     2068  0.0  0.1   5792   816 pts/0    S+   13:17   0:00 grep --color=auto cups
scorp@scorp:~$