all in one pc de paket ve internet sorunu.

Başlatan cxa1294, 26 Aralık 2011 - 00:01:58

« önceki - sonraki »

0 Üyeler ve 2 Ziyaretçi konuyu incelemekte.

Yazdır
Aşağı git Sayfa1 2
Kullanıcı Eylemleri

cxa1294

26 Aralık 2011 - 00:01:58 Son düzenlenme: 27 Aralık 2011 - 16:42:29 cerencalici
Herkese merhaba.
Yaklaşık 7-8 aydır Ubuntu(11.04 - 11.10) kullanıcısıyım. Öncesinde de Pardus kullanmışlığım var (6-7 ay kadar.)
Elimde p4 masaüstü (hepsi bir arada-all in one) Sony Vaio var.
Hard diskini max blast ile sıfırladım. Linux kurmak istedim. Önce Kubuntu(11.04) denedim. Kuruldu ama inanılmaz yavaştı, oldukça donuk çalışıyordu.
Mint (11 ve 12) kurmaya çalıştım, ilginçtir her iki sürüm için farklı hızlarda yazılmış hiçbir kurulum CD'sine bilgisayar tepki dahi vermedi (compability mode dahil olmak üzere).
Sadece bir tanesine tepki verdi ama kurmadı uyumluluk testi yaptım, bir dosya için hata verdi ama ne olduğunu asla öğrenemedim.
Ubuntu 11.10 kurdum ama bilgisayar İnternet kablosunu takınca 5-10 saniye sonra "disconnect" diyor.
network tools'dan kontrol edince "link speed not available" diyor ve ayrıca network device her açılış kapanıştan sonra ethernet interface'den loopback interface'e dönüyor.
Forumlardan birkaç bulduğum bazı komutları denedim ama paketin (örneğin ethtool) yüklü olmadığını söylüyor.
Paket yükleyebilmem için İnternet'e ihtiyacım var ama İnternet bağlantısını kuramıyorum.
Makine sadece CD okuyabiliyor, bu yüzden DVD ile kurulum yapamıyorum. Yardımlarınız için şimdiden teşekkür ederim.

if

#1
26 Aralık 2011 - 00:37:49
ethtool'u bir başka yerden indirip Ubuntu'ya taşıdıktan sonra
Kod Seç
sudo dpkg -i paketin_ismi komutuyla kurabilirsin. Gerekli çıktıları alabilir miyim?: http://forum.ubuntu-tr.net/index.php?topic=28764.0

cxa1294

#2
26 Aralık 2011 - 17:24:39 Son düzenlenme: 29 Aralık 2011 - 16:21:37 if
ethtool indirdim ama kuramadım.
Kod Seç
lspci
lsusb
ifconfig
iwconfig
iwlist scanning
lsmod
rfkill list
sudo lshw -C network
dmesg

komutlarından çıktı alıyordum rfkill list komutuna hiçbir tepki vermedi.
dmesg komutunun çıktısını verdi, ben alamadan makine kilitlendi ve hiçbir şekilde açılmıyor şu an.
Tekrar normal hâle döndürmeye çalışacağım. Gelişmelerden haberdar ederim. İlginize teşekkür ederim.

if

#3
26 Aralık 2011 - 20:54:31
@cxa1294, ethtool'un yüklü olarak gelmesi gerek aslında. İlginç...O verdiğim komutlar bilgisayarın kilitlenmesine yol açmaz. Bilgisayarın ne kadar ram'i var? Ekran kartı nedir?

cxa1294

#4
26 Aralık 2011 - 22:22:04 Son düzenlenme: 27 Aralık 2011 - 16:45:22 cerencalici
Bilgisayarın ram'i 512mb ekran kartı onboard.
Sony Vaio Pentium4 işlemcili makine.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 26 Aralık 2011 - 22:29:00

Konunun başında anlattığım gibi elimdeki Linux dağıtımlarından sadece Ubuntu uyum gösterdi. Kubuntu kuruldu ama çok yavaştı (Kubuntu'da disconnect oluyordu.).
Linux Mint dağıtımlarının maalesef hiçbiri tepki vermedi.
Ubuntu kuruldu ama anladığım kadarı ile birçok paket kurulmadı. Bunu forumlardan bulup denediğim komutlardan anlıyorum.
Elimde Ubuntu 8.04 live CD var. Bunu kurup çeşitli update veya upgrade'ler ile sürüm yükseltmesi yoluna gideceğim.

if

#5
26 Aralık 2011 - 22:35:18
@cxa1294, alternatif cd ile kurulum yap. Öbürü çok eski, güncellemeyle olacak iş değil o.

http://www.ubuntu.com/download/ubuntu/alternative-download#alternate

cxa1294

#6
27 Aralık 2011 - 15:48:13 Son düzenlenme: 27 Aralık 2011 - 16:46:26 cerencalici
Alternatif kurulum CD'sini açmıyor makine.
Ubuntu 9.04 jaunty jackalope live CD'sini deniyorum, direkt açıyor.
Hard diski sıfırlayıp alternatif CD'den mi yükleme yapsam?

if

#7
27 Aralık 2011 - 15:57:24 Son düzenlenme: 27 Aralık 2011 - 16:47:06 cerencalici
Dahili diski sıfırlamanın çözüm olacağını zannetmiyorum, bir sorunu olmadıktan sonra belleğin. O şekilde sürüm yükseltilebilir ama meşakkatli olur. Neredeyse sistemin tamamen değişmesi gerek. Acaba tekrardan Ubuntu yüklense de bağlanma sorununa odaklansak. Ya da direkt RAM'e kurulan Puppy Linux denenebilir.

cxa1294

#8
27 Aralık 2011 - 16:05:09
son kez şansımı deneyeceğim ubuntu için. olmazsa puppy linux herhalde.

cxa1294

#9
29 Aralık 2011 - 16:17:18 Son düzenlenme: 29 Aralık 2011 - 16:20:07 if
ubuntu 11.10 alternatif iso yükledim ama sorun devam ediyor. çıktıları veriyorum.
bu arada nedendir bilmiyorum ama dmesg komutunu yazıyorum ve her defasında bilgisayar kilitleniyor. (daha önce de aynı şeyi yapmıştı)
Kod Seç

alev@alev:~$ cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=11.10
DISTRIB_CODENAME=oneiric
DISTRIB_DESCRIPTION="Ubuntu 11.10"

****************

Kod Seç
alev@alev:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 651 Host (rev 02)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2/3 SMBus controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:13.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02)
00:13.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 65x/M650/740 PCI/AGP VGA Display Adapter

********************************
Kod Seç
alev@alev:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c50f Logitech, Inc.
Bus 003 Device 002: ID 054c:00cd Sony Corp.
*************************

Kod Seç
alev@alev:~$ sudo lshw -C network
[sudo] password for alev:
  *-network               
       description: Ethernet interface
       product: RTL-8139/8139C/8139C+
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 12
       bus info: pci@0000:00:12.0
       logical name: eth0
       version: 10
       serial: 00:0c:6e:c0:5d:b8
       size: 10Mbit/s
       capacity: 100Mbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s
       resources: irq:17 ioport:8800(size=256) memory:e9800000-e98000ff
************************
Kod Seç
alev@alev:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:0c:6e:c0:5d:b8 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17 Base address:0x8800

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:96 errors:0 dropped:0 overruns:0 frame:0
          TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:7584 (7.5 KB)  TX bytes:7584 (7.5 KB)
**************************************

Kod Seç
alev@alev:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.
*********************************
Kod Seç
alev@alev:~$ iwlist scanning
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.
************************************
Kod Seç
alev@alev:~$ lsmod
Module                  Size  Used by
nls_iso8859_1          12617  1
nls_cp437              12751  1
vfat                   17308  1
fat                    55577  1 vfat
usb_storage            44173  1
uas                    17699  0
bnep                   17923  2
bluetooth             148839  7 bnep
parport_pc             32114  0
ppdev                  12849  0
vesafb                 13489  1
snd_intel8x0           33318  2
snd_ac97_codec        106082  1 snd_intel8x0
ac97_bus               12642  1 snd_ac97_codec
snd_pcm                80468  2 snd_intel8x0,snd_ac97_codec
snd_seq_midi           13132  0
snd_rawmidi            25241  1 snd_seq_midi
snd_seq_midi_event     14475  1 snd_seq_midi
pcmcia                 39822  0
snd_seq                51567  2 snd_seq_midi,snd_seq_midi_event
snd_timer              28932  2 snd_pcm,snd_seq
snd_seq_device         14172  3 snd_seq_midi,snd_rawmidi,snd_seq
snd                    55902  11 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
yenta_socket           27428  0
pcmcia_rsrc            18367  1 yenta_socket
serio_raw              12990  0
pcmcia_core            21511  3 pcmcia,yenta_socket,pcmcia_rsrc
soundcore              12600  1 snd
snd_page_alloc         14115  2 snd_intel8x0,snd_pcm
sony_laptop            39681  0
binfmt_misc            17292  1
i2c_sis96x             12743  0
shpchp                 32356  0
sis_agp                13165  1
lp                     17455  0
parport                40930  3 parport_pc,ppdev,lp
usbhid                 41905  0
hid                    77367  1 usbhid
firewire_ohci          35854  0
8139too                23283  0
8139cp                 22636  0
firewire_core          56937  1 firewire_ohci
crc_itu_t              12627  1 firewire_core

if

#10
29 Aralık 2011 - 16:48:16
@cxa1294, Silicon ekran kartı vermış ki bu güzel haber değil. Firma Linux'a 3B desteği vermiyor ayrıca sağlanan sürücüler de pek iyi değil.
Kod Seç
dmesg komutuna verdiği tepki garip.

Şu çıktıları da alayım:
Kod Seç
cat /var/log/Xorg.0.log
dmesg > dmesg.txt
dpkg -l | grep xserver-xorg-video
sudo find / -name sis_drv.o

cxa1294

#11
29 Aralık 2011 - 17:11:28 Son düzenlenme: 29 Aralık 2011 - 17:41:50 cerencalici
dmesg > dmesg.txt , sudo find / -name sis_drv.o komutlarına çıktı vermedi
sudo find / -name sis_drv.o komutuna password sordu ama bir şey yapmadı.
çıktılar
Kod Seç

[    19.459] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    19.459] (II) Module record: vendor="X.Org Foundation"
[    19.459] compiled for 1.10.4, module version = 1.13.0
[    19.459] Module class: X.Org Server Extension
[    19.459] ABI class: X.Org Server Extension, version 5.0
[    19.459] (II) Loading extension RECORD
[    19.459] (II) LoadModule: "dri"
[    19.462] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    19.462] (II) Module dri: vendor="X.Org Foundation"
[    19.462] compiled for 1.10.4, module version = 1.0.0
[    19.462] ABI class: X.Org Server Extension, version 5.0
[    19.462] (II) Loading extension XFree86-DRI
[    19.462] (II) LoadModule: "dri2"
[    19.463] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    19.463] (II) Module dri2: vendor="X.Org Foundation"
[    19.463] compiled for 1.10.4, module version = 1.2.0
[    19.463] ABI class: X.Org Server Extension, version 5.0
[    19.463] (II) Loading extension DRI2
[    19.463] (==) Matched sis as autoconfigured driver 0
[    19.463] (==) Matched vesa as autoconfigured driver 1
[    19.463] (==) Matched fbdev as autoconfigured driver 2
[    19.463] (==) Assigned the driver to the xf86ConfigLayout
[    19.463] (II) LoadModule: "sis"
[    19.467] (II) Loading /usr/lib/xorg/modules/drivers/sis_drv.so
[    19.467] (II) Module sis: vendor="X.Org Foundation"
[    19.467] compiled for 1.10.1, module version = 0.10.3
[    19.467] Module class: X.Org Video Driver
[    19.467] ABI class: X.Org Video Driver, version 10.0
[    19.467] (II) LoadModule: "vesa"
[    19.468] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    19.468] (II) Module vesa: vendor="X.Org Foundation"
[    19.468] compiled for 1.10.2, module version = 2.3.0
[    19.468] Module class: X.Org Video Driver
[    19.468] ABI class: X.Org Video Driver, version 10.0
[    19.468] (II) LoadModule: "fbdev"
[    19.469] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    19.469] (II) Module fbdev: vendor="X.Org Foundation"
[    19.469] compiled for 1.10.0, module version = 0.4.2
[    19.469] ABI class: X.Org Video Driver, version 10.0
[    19.469] (II) SIS: driver for SiS chipsets: SIS5597/5598, SIS530/620,
SIS6326/AGP/DVD, SIS300/305, SIS630/730, SIS540, SIS315, SIS315H,
SIS315PRO/E, SIS550, SIS650/M650/651/740, SIS330(Xabre),
SIS660/[M]661[F|M]X/[M]670/[M]741[GX]/[M]760[GX]/[M]761[GX]/[M]770[GX],
SIS340
[    19.469] (II) SIS: driver for XGI chipsets: Volari Z7 (XG20),
Volari V3XT/V5/V8/Duo (XG40)
[    19.469] (II) VESA: driver for VESA chipsets: vesa
[    19.469] (II) FBDEV: driver for framebuffer: fbdev
[    19.469] (++) using VT number 7

[    19.469] (WW) Falling back to old probe method for sis
[    19.469] (--) Assigning device section with no busID to primary device
[    19.469] (--) Chipset SIS650/M650/651/740 found
[    19.469] (II) Loading /usr/lib/xorg/modules/drivers/sis_drv.so
[    19.470] (WW) Falling back to old probe method for vesa
[    19.470] (WW) Falling back to old probe method for fbdev
[    19.470] (II) Loading sub module "fbdevhw"
[    19.470] (II) LoadModule: "fbdevhw"
[    19.470] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    19.470] (II) Module fbdevhw: vendor="X.Org Foundation"
[    19.470] compiled for 1.10.4, module version = 0.0.2
[    19.470] ABI class: X.Org Video Driver, version 10.0
[    19.470] (II) SIS(0): SiS driver (2005/09/20-1, compiled for X.org 1.10.1.0)
[    19.470] (II) SIS(0): Copyright (C) 2001-2005 Thomas Winischhofer <thomas@winischhofer.net> and others
[    19.470] (II) SIS(0): *** See http://www.winischhofer.eu/linuxsisvga.shtml
[    19.470] (II) SIS(0): *** for documentation and updates.
[    19.471] (--) SIS(0): sisfb not found
[    19.471] (--) SIS(0): Relocated I/O registers at 0xD800
[    19.471] (II) Loading sub module "ramdac"
[    19.471] (II) LoadModule: "ramdac"
[    19.471] (II) Module "ramdac" already built-in
[    19.471] (II) SIS(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[    19.471] (==) SIS(0): Depth 24, (--) framebuffer bpp 32
[    19.471] (==) SIS(0): RGB weight 888
[    19.471] (==) SIS(0): Default visual is TrueColor
[    19.473] (--) SIS(0): Video BIOS version "1.11s  " found (old SiS data layout)
[    19.473] (==) SIS(0): Using XAA acceleration architecture
[    19.473] (==) SIS(0): Using HW cursor
[    19.473] (==) SIS(0): Color HW cursor is enabled
[    19.473] (II) SIS(0): Using VRAM command queue, size 512k
[    19.473] (==) SIS(0): Hotkey display switching is enabled
[    19.473] (II) SIS(0): WARNING: Using the Hotkey might freeze your machine, regardless
[    19.473] (II) SIS(0):          whether enabled or disabled. This is no driver bug.
[    19.473] (==) SIS(0): SiSCtrl utility interface is disabled
[    19.473] (II) SIS(0): For information on SiSCtrl, see
http://www.winischhofer.eu/linuxsispart1.shtml#sisctrl
[    19.473] (==) SIS(0): DRI disabled
[    19.473] (II) SIS(0): Checking OS for SSE support is not supported in this version of X.org
[    19.473] (II) SIS(0): If your OS supports SSE, set the option "UseSSE" to "on".
[    19.474] (--) SIS(0): DIMM0 is DDR SDRAM
[    19.474] (--) SIS(0): DIMM1 is not installed
[    19.474] (--) SIS(0): DIMM2 is not installed
[    19.474] (--) SIS(0): DIMM3 is not installed
[    19.474] (--) SIS(0): DRAM type: DDR SDRAM
[    19.474] (--) SIS(0): Memory clock: 332.892 MHz
[    19.474] (--) SIS(0): DRAM bus width: 64 bit
[    19.474] (--) SIS(0): Linear framebuffer at 0xF0000000
[    19.474] (--) SIS(0): MMIO registers at 0xEB800000 (size 64K)
[    19.474] (--) SIS(0): VideoRAM: 32768 KB
[    19.474] (II) SIS(0): Using 32192K of framebuffer memory at offset 0K
[    19.474] (--) SIS(0): SiS650 revision ID e0 (651)
[    19.474] (--) SIS(0): Hardware supports two video overlays
[    19.474] (--) SIS(0): Detected SiS301LV video bridge (Charter/UMC-1, ID 1; Rev 0xd1)
[    21.293] (--) SIS(0): No CRT1/VGA detected
[    21.293] (--) SIS(0): Detected LCD/plasma panel (1024x768, 1, exp., RGB18 [02d300])
[    21.293] (==) SIS(0): Using gamma correction (1.0, 1.0, 1.0)
[    21.293] (II) SIS(0): CRT1 gamma correction is enabled
[    21.293] (II) SIS(0): Separate Xv gamma correction for CRT1 is disabled
[    21.293] (II) SIS(0): CRT2 gamma correction is enabled
[    21.293] (--) SIS(0): Memory bandwidth at 32 bpp is 665.784 MHz
[    21.293] (--) SIS(0): Detected LCD PanelDelayCompensation 0x04 (for LCD=CRT2)
[    21.293] (--) SIS(0): Detected LCD PanelDelayCompensation1 0x04 (for LCD=CRT1)
[    21.293] (II) Loading sub module "ddc"
[    21.293] (II) LoadModule: "ddc"
[    21.293] (II) Module "ddc" already built-in
[    21.293] (--) SIS(0): CRT2 DDC probing failed
[    21.293] (==) SIS(0): Min pixel clock is 10 MHz
[    21.293] (--) SIS(0): Max pixel clock is 340 MHz
[    21.294] (II) SIS(0): Replaced entire mode list with built-in modes
[    21.294] (II) SIS(0): Correcting missing CRT2 monitor HSync range
[    21.294] (II) SIS(0): Correcting missing CRT2 monitor VRefresh range
[    21.294] (II) SIS(0): "Unknown reason" in the following list means that the mode
[    21.294] (II) SIS(0): is not supported on the chipset/bridge/current output device.
[    21.294] (II) SIS(0): <default monitor>: Using hsync range of 30.00-80.00 kHz
[    21.294] (II) SIS(0): <default monitor>: Using vrefresh range of 59.00-61.00 Hz
[    21.294] (II) SIS(0): <default monitor>: Using vrefresh value of 71.00 Hz
[    21.294] (WW) SIS(0): Unable to estimate virtual size
[    21.294] (II) SIS(0): Clock range:  10.00 to 340.00 MHz
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "800x600" (hsync out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (hsync out of range)
[    21.294] (II) SIS(0): Not using default mode "640x480" (hsync out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (vrefresh out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (hsync out of range)
[    21.294] (II) SIS(0): Not using default mode "1024x768" (hsync out of range)
[    21.294] (II) SIS(0): Not using default mode "1280x1024" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1280x1024" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1280x1024" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1280x1024" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1600x1200" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
[    21.294] (II) SIS(0): Not using default mode "2048x1536" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "2048x1536" (unknown reason)
[    21.294] (II) SIS(0): Not using default mode "2048x1536" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
[    21.295] (II) SIS(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
[    21.295] (II) SIS(0): Not using default mode "800x480" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "800x480" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "1024x576" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "1024x576" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "1280x720" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x720" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x720" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x960" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x960" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x768" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x768" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x768" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1400x1050" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1400x1050" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1152x864" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1152x864" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1152x864" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "848x480" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "856x480" (vrefresh out of range)
[    21.295] (II) SIS(0): Not using default mode "1360x768" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x800" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x800" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x800" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1680x1050" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1920x1080" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x854" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x854" (unknown reason)
[    21.295] (II) SIS(0): Not using default mode "1280x854" (unknown reason)
[    21.295] (--) SIS(0): Virtual size is 1024x768 (pitch 1024)
[    21.295] (**) SIS(0): *Default mode "1024x768" (1024x768) (For CRT device: 65.1 MHz, 48.5 kHz, 60.1 Hz)
[    21.295] (**) SIS(0): *Default mode "1024x576" (1024x576) (For CRT device: 65.1 MHz, 48.5 kHz, 60.1 Hz)
[    21.295] (**) SIS(0): *Default mode "960x600" (960x600) (For CRT device: 41.5 MHz, 37.1 kHz, 60.0 Hz)
[    21.295] (**) SIS(0): *Default mode "960x540" (960x540) (For CRT device: 37.3 MHz, 33.8 kHz, 60.0 Hz)
[    21.295] (**) SIS(0): *Default mode "800x600" (800x600) (For CRT device: 40.0 MHz, 37.9 kHz, 60.3 Hz)
[    21.295] (**) SIS(0): *Default mode "768x576" (768x576) (For CRT device: 35.0 MHz, 35.9 kHz, 60.1 Hz)
[    21.295] (**) SIS(0): *Default mode "720x576" (720x576) (For CRT device: 32.7 MHz, 35.9 kHz, 60.1 Hz)
[    21.295] (**) SIS(0): *Default mode "856x480" (856x480) (For CRT device: 33.9 MHz, 31.7 kHz, 59.8 Hz)
[    21.295] (**) SIS(0): *Default mode "848x480" (848x480) (For CRT device: 33.7 MHz, 31.0 kHz, 60.0 Hz)
[    21.295] (**) SIS(0): *Default mode "800x480" (800x480) (For CRT device: 39.8 MHz, 37.7 kHz, 60.0 Hz)
[    21.295] (**) SIS(0): *Default mode "720x480" (720x480) (For CRT device: 28.3 MHz, 31.6 kHz, 61.0 Hz)
[    21.295] (**) SIS(0): *Default mode "640x480" (640x480) (For CRT device: 25.1 MHz, 31.3 kHz, 59.7 Hz)
[    21.295] (**) SIS(0): *Default mode "640x400" (640x400) (For CRT device: 25.1 MHz, 31.6 kHz, 71.6 Hz)
[    21.295] (**) SIS(0): *Default mode "512x384" (512x384) (For CRT device: 32.6 MHz, 48.5 kHz, 60.1 Hz (D))
[    21.295] (**) SIS(0): *Default mode "400x300" (400x300) (For CRT device: 20.0 MHz, 37.9 kHz, 60.3 Hz (D))
[    21.295] (**) SIS(0): *Default mode "320x240" (320x240) (For CRT device: 12.5 MHz, 31.3 kHz, 60.7 Hz (D))
[    21.295] (**) SIS(0): *Default mode "320x200" (320x200) (For CRT device: 12.5 MHz, 31.3 kHz, 70.9 Hz (D))
[    21.295] (==) SIS(0): DPI set to (96, 96)
[    21.295] (II) Loading sub module "fb"
[    21.295] (II) LoadModule: "fb"
[    21.296] (II) Loading /usr/lib/xorg/modules/libfb.so
[    21.296] (II) Module fb: vendor="X.Org Foundation"
[    21.296] compiled for 1.10.4, module version = 1.0.0
[    21.296] ABI class: X.Org ANSI C Emulation, version 0.4
[    21.296] (II) Loading sub module "xaa"
[    21.296] (II) LoadModule: "xaa"
[    21.297] (II) Loading /usr/lib/xorg/modules/libxaa.so
[    21.297] (II) Module xaa: vendor="X.Org Foundation"
[    21.297] compiled for 1.10.4, module version = 1.2.1
[    21.297] ABI class: X.Org Video Driver, version 10.0
[    21.297] (II) SIS(0): 2D acceleration enabled
[    21.297] (II) UnloadModule: "vesa"
[    21.297] (II) Unloading vesa
[    21.297] (II) UnloadModule: "fbdev"
[    21.297] (II) Unloading fbdev
[    21.297] (II) UnloadModule: "fbdevhw"
[    21.297] (II) Unloading fbdevhw
[    21.297] (--) Depth 24 pixmap format is 32 bpp
[    21.297] (II) Loading sub module "vbe"
[    21.297] (II) LoadModule: "vbe"
[    21.297] (II) Loading /usr/lib/xorg/modules/libvbe.so
[    21.298] (II) Module vbe: vendor="X.Org Foundation"
[    21.298] compiled for 1.10.4, module version = 1.1.0
[    21.298] ABI class: X.Org Video Driver, version 10.0
[    21.298] (II) Loading sub module "int10"
[    21.298] (II) LoadModule: "int10"
[    21.298] (II) Loading /usr/lib/xorg/modules/libint10.so
[    21.298] (II) Module int10: vendor="X.Org Foundation"
[    21.298] compiled for 1.10.4, module version = 1.0.0
[    21.298] ABI class: X.Org Video Driver, version 10.0
[    21.298] (II) SIS(0): initializing int10
[    21.302] (II) SIS(0): Primary V_BIOS segment is: 0xc000
[    21.332] (II) SIS(0): VESA BIOS detected
[    21.332] (II) SIS(0): VESA VBE Version 3.0
[    21.332] (II) SIS(0): VESA VBE Total Mem: 32768 kB
[    21.332] (II) SIS(0): VESA VBE OEM: SiS
[    21.332] (II) SIS(0): VESA VBE OEM Software Rev: 1.0
[    21.332] (II) SIS(0): VESA VBE OEM Vendor: Silicon Integrated Systems Corp.
[    21.332] (II) SIS(0): VESA VBE OEM Product: 6325
[    21.332] (II) SIS(0): VESA VBE OEM Product Rev: 1.11s 
[    21.712] (II) SIS(0): Setting standard mode 0x64
[    22.021] (II) SIS(0): RENDER acceleration enabled
[    22.021] (II) SIS(0): Framebuffer from (0,0) to (1023,8046)
[    22.021] (II) SIS(0): Using XFree86 Acceleration Architecture (XAA)
[    22.021] Screen to screen bit blits
[    22.021] Solid filled rectangles
[    22.021] 8x8 mono pattern filled rectangles
[    22.021] 8x8 color pattern filled rectangles
[    22.021] Solid Lines
[    22.021] Dashed Lines
[    22.021] Setting up tile and stipple cache:
[    22.021] 32 128x128 slots
[    22.021] 32 256x256 slots
[    22.021] 16 512x512 slots
[    22.021] 32 8x8 color pattern slots
[    22.022] (--) SIS(0): CPU frequency 2400.08Mhz
[    22.024] (II) SIS(0): Benchmarking system RAM to video RAM memory transfer methods:
[    22.037] (--) SIS(0): Checked libc memcpy()... 256.8 MiB/s
[    22.049] (--) SIS(0): Checked built-in-1 memcpy()... 270.4 MiB/s
[    22.123] (--) SIS(0): Checked built-in-2 memcpy()... 35.5 MiB/s
[    22.135] (--) SIS(0): Checked MMX memcpy()... 261.9 MiB/s
[    22.145] (--) SIS(0): Checked MMX2 memcpy()... 310.7 MiB/s
[    22.146] (--) SIS(0): Using MMX2 method for aligned data transfers to video RAM
[    22.146] (--) SIS(0): Using MMX2 method for unaligned data transfers to video RAM
[    22.146] (==) SIS(0): Backing store disabled
[    22.146] (==) SIS(0): Silken mouse enabled
[    22.147] (==) SIS(0): DPMS enabled
[    22.147] (II) SIS(0): Using SiS300/315/330/340 series HW Xv
[    22.147] (II) SIS(0): Default Xv adaptor is Video Overlay
[    22.194] (II) SIS(0): Initialized SISCTRL extension version 0.1
[    22.194] (II) SIS(0): Registered screen 0 with SISCTRL extension version 0.1
[    22.194] (==) RandR enabled
[    22.194] (II) Initializing built-in extension Generic Event Extension
[    22.194] (II) Initializing built-in extension SHAPE
[    22.194] (II) Initializing built-in extension MIT-SHM
[    22.194] (II) Initializing built-in extension XInputExtension
[    22.194] (II) Initializing built-in extension XTEST
[    22.194] (II) Initializing built-in extension BIG-REQUESTS
[    22.194] (II) Initializing built-in extension SYNC
[    22.194] (II) Initializing built-in extension XKEYBOARD
[    22.194] (II) Initializing built-in extension XC-MISC
[    22.194] (II) Initializing built-in extension SECURITY
[    22.194] (II) Initializing built-in extension XINERAMA
[    22.194] (II) Initializing built-in extension XFIXES
[    22.194] (II) Initializing built-in extension RENDER
[    22.194] (II) Initializing built-in extension RANDR
[    22.194] (II) Initializing built-in extension COMPOSITE
[    22.194] (II) Initializing built-in extension DAMAGE
[    22.194] (II) Initializing built-in extension GESTURE
[    22.209] (II) AIGLX: Screen 0 is not DRI2 capable
[    22.209] (II) AIGLX: Screen 0 is not DRI capable
[    22.209] (II) AIGLX: Trying DRI driver /usr/lib/i386-linux-gnu/dri/swrast_dri.so
[    22.217] (II) AIGLX: Loaded and initialized swrast
[    22.217] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[    22.233] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[    22.263] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    22.263] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    22.263] (II) LoadModule: "evdev"
[    22.263] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.265] (II) Module evdev: vendor="X.Org Foundation"
[    22.265] compiled for 1.10.2, module version = 2.6.0
[    22.265] Module class: X.Org XInput Driver
[    22.265] ABI class: X.Org XInput driver, version 12.3
[    22.265] (II) Using input driver 'evdev' for 'Power Button'
[    22.265] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.265] (**) Power Button: always reports core events
[    22.265] (**) Power Button: Device: "/dev/input/event1"
[    22.265] (--) Power Button: Found keys
[    22.265] (II) Power Button: Configuring as keyboard
[    22.265] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[    22.265] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    22.265] (**) Option "xkb_rules" "evdev"
[    22.265] (**) Option "xkb_model" "pc105"
[    22.265] (**) Option "xkb_layout" "tr"
[    22.270] (II) XKB: reuse xkmfile /var/lib/xkb/server-609880D4F1521A95A29BCD7AB1227A69EC9A1B72.xkm
[    22.273] (II) config/udev: Adding input device Sony Vaio Keys (/dev/input/event5)
[    22.274] (**) Sony Vaio Keys: Applying InputClass "evdev keyboard catchall"
[    22.274] (II) Using input driver 'evdev' for 'Sony Vaio Keys'
[    22.274] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.274] (**) Sony Vaio Keys: always reports core events
[    22.274] (**) Sony Vaio Keys: Device: "/dev/input/event5"
[    22.274] (--) Sony Vaio Keys: Found keys
[    22.274] (II) Sony Vaio Keys: Configuring as keyboard
[    22.274] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:09/SNY5001:00/input/input5/event5"
[    22.274] (II) XINPUT: Adding extended input device "Sony Vaio Keys" (type: KEYBOARD)
[    22.274] (**) Option "xkb_rules" "evdev"
[    22.274] (**) Option "xkb_model" "pc105"
[    22.274] (**) Option "xkb_layout" "tr"
[    22.275] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    22.275] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    22.275] (II) Using input driver 'evdev' for 'Power Button'
[    22.275] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.276] (**) Power Button: always reports core events
[    22.276] (**) Power Button: Device: "/dev/input/event0"
[    22.276] (--) Power Button: Found keys
[    22.276] (II) Power Button: Configuring as keyboard
[    22.276] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
[    22.276] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    22.276] (**) Option "xkb_rules" "evdev"
[    22.276] (**) Option "xkb_model" "pc105"
[    22.276] (**) Option "xkb_layout" "tr"
[    22.284] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event2)
[    22.284] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[    22.284] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[    22.284] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.284] (**) Logitech USB Receiver: always reports core events
[    22.284] (**) Logitech USB Receiver: Device: "/dev/input/event2"
[    22.284] (--) Logitech USB Receiver: Found keys
[    22.284] (II) Logitech USB Receiver: Configuring as keyboard
[    22.284] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.0/input/input2/event2"
[    22.284] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD)
[    22.284] (**) Option "xkb_rules" "evdev"
[    22.284] (**) Option "xkb_model" "pc105"
[    22.284] (**) Option "xkb_layout" "tr"
[    22.286] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event3)
[    22.286] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[    22.286] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[    22.286] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[    22.286] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.286] (**) Logitech USB Receiver: always reports core events
[    22.286] (**) Logitech USB Receiver: Device: "/dev/input/event3"
[    22.286] (--) Logitech USB Receiver: Found 20 mouse buttons
[    22.286] (--) Logitech USB Receiver: Found scroll wheel(s)
[    22.286] (--) Logitech USB Receiver: Found relative axes
[    22.286] (--) Logitech USB Receiver: Found x and y relative axes
[    22.286] (--) Logitech USB Receiver: Found keys
[    22.286] (II) Logitech USB Receiver: Configuring as mouse
[    22.286] (II) Logitech USB Receiver: Configuring as keyboard
[    22.286] (II) Logitech USB Receiver: Adding scrollwheel support
[    22.286] (**) Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[    22.286] (**) Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.287] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.1/input/input3/event3"
[    22.287] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD)
[    22.287] (**) Option "xkb_rules" "evdev"
[    22.287] (**) Option "xkb_model" "pc105"
[    22.287] (**) Option "xkb_layout" "tr"
[    22.287] (II) Logitech USB Receiver: initialized for relative axes.
[    22.287] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[    22.287] (**) Logitech USB Receiver: (accel) acceleration profile 0
[    22.287] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[    22.287] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[    22.288] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[    22.288] (II) No input driver/identifier specified (ignoring)
[    22.290] (II) config/udev: Adding input device Sony Sony IR Receiver (/dev/input/event4)
[    22.290] (**) Sony Sony IR Receiver: Applying InputClass "evdev keyboard catchall"
[    22.290] (II) Using input driver 'evdev' for 'Sony Sony IR Receiver'
[    22.290] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.290] (**) Sony Sony IR Receiver: always reports core events
[    22.290] (**) Sony Sony IR Receiver: Device: "/dev/input/event4"
[    22.290] (--) Sony Sony IR Receiver: Found keys
[    22.290] (II) Sony Sony IR Receiver: Configuring as keyboard
[    22.290] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:03.1/usb3/3-3/3-3:1.0/input/input4/event4"
[    22.290] (II) XINPUT: Adding extended input device "Sony Sony IR Receiver" (type: KEYBOARD)
[    22.290] (**) Option "xkb_rules" "evdev"
[    22.290] (**) Option "xkb_model" "pc105"
[    22.290] (**) Option "xkb_layout" "tr"
[    22.305] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/event6)
[    22.305] (II) No input driver/identifier specified (ignoring)
[    22.305] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/mouse1)
[    22.305] (II) No input driver/identifier specified (ignoring)
[    97.491] (II) XKB: reuse xkmfile /var/lib/xkb/server-24EEF4C45DB2CCF1F3CEEDDB8005FC5F0B3CC871.xkm
[   133.771] (II) XKB: reuse xkmfile /var/lib/xkb/server-24EEF4C45DB2CCF1F3CEEDDB8005FC5F0B3CC871.xkm
alev@alev:~$ dpkg -l | grep xserver-xorg-video
ii  xserver-xorg-video-all                 1:7.6+7ubuntu7                          X.Org X server -- output driver metapackage
ii  xserver-xorg-video-ati                 1:6.14.99~git20110811.g93fc084-0ubuntu1 X.Org X server -- AMD/ATI display driver wrapper
ii  xserver-xorg-video-cirrus              1:1.3.2-2ubuntu7                        X.Org X server -- Cirrus display driver
ii  xserver-xorg-video-fbdev               1:0.4.2-3ubuntu6                        X.Org X server -- fbdev display driver
ii  xserver-xorg-video-geode               2.11.12-2                               X.Org X server -- Geode GX2/LX display driver
ii  xserver-xorg-video-intel               2:2.15.901-1ubuntu2                     X.Org X server -- Intel i8xx, i9xx display driver
ii  xserver-xorg-video-mach64              6.9.0-1                                 X.Org X server -- ATI Mach64 display driver
ii  xserver-xorg-video-mga                 1:1.4.13.dfsg-3build1                   X.Org X server -- MGA display driver
ii  xserver-xorg-video-neomagic            1:1.2.5-2                               X.Org X server -- Neomagic display driver
ii  xserver-xorg-video-nouveau             1:0.0.16+git20110411+8378443-1          X.Org X server -- Nouveau display driver (experimental)
ii  xserver-xorg-video-openchrome          1:0.2.904+svn920-1                      X.Org X server -- VIA display driver
ii  xserver-xorg-video-qxl                 0.0.14-1                                X.Org X server -- QXL display driver
ii  xserver-xorg-video-r128                6.8.1-5                                 X.Org X server -- ATI r128 display driver
ii  xserver-xorg-video-radeon              1:6.14.99~git20110811.g93fc084-0ubuntu1 X.Org X server -- AMD/ATI Radeon display driver
ii  xserver-xorg-video-s3                  1:0.6.3-4                               X.Org X server -- legacy S3 display driver
ii  xserver-xorg-video-savage              1:2.3.2-3ubuntu2                        X.Org X server -- Savage display driver
ii  xserver-xorg-video-siliconmotion       1:1.7.5-1                               X.Org X server -- SiliconMotion display driver
ii  xserver-xorg-video-sis                 1:0.10.3-3                              X.Org X server -- SiS display driver
ii  xserver-xorg-video-sisusb              1:0.9.4-2                               X.Org X server -- SiS USB display driver
ii  xserver-xorg-video-tdfx                1:1.4.3-4                               X.Org X server -- tdfx display driver
ii  xserver-xorg-video-trident             1:1.3.4-2                               X.Org X server -- Trident display driver
ii  xserver-xorg-video-vesa                1:2.3.0-7                               X.Org X server -- VESA display driver
ii  xserver-xorg-video-vmware              1:11.0.3-2                              X.Org X server -- VMware display driver
alev@alev:~$


if

#12
29 Aralık 2011 - 17:38:30
@cxa1294, kullanıcı ev dizini altında dmesg.txt diye bir dosya vardır. Onun içeriğini buraya geçin.

cxa1294

#13
29 Aralık 2011 - 19:33:47
biraz gecikmeli oldu kusura bakmayın.
Kod Seç

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.0-12-generic (buildd@vernadsky) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 (Ubuntu 3.0.0-12.20-generic 3.0.4)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001dffc000 (usable)
[    0.000000]  BIOS-e820: 000000001dffc000 - 000000001dfff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001dfff000 - 000000001e000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] NX (Execute Disable) protection: approximated by x86 segment limits
[    0.000000] DMI 2.3 present.
[    0.000000] DMI: Sony Corporation PCV-V100G/PIZZA, BIOS ACPI BIOS Revision 1003 09/18/2003
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x1dffc max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FE0000000 write-back
[    0.000000]   1 base 01E000000 mask FFE000000 uncachable
[    0.000000]   2 base 0EC000000 mask FFC000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 01c00000
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: 0000000000000000-000000001dffc000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 001dc00000 page 2M
[    0.000000]  001dc00000 - 001dffc000 page 4k
[    0.000000] kernel direct mapping tables up to 1dffc000 @ 1bfb000-1c00000
[    0.000000] RAMDISK: 1cba7000 - 1d8a5000
[    0.000000] ACPI: RSDP 000f64d0 00014 (v00 ASUS  )
[    0.000000] ACPI: RSDT 1dffc000 00030 (v01 ASUS   PIZZA    42302E31 MSFT 31313031)
[    0.000000] ACPI: FACP 1dffc0c0 00074 (v01 ASUS   PIZZA    42302E31 MSFT 31313031)
[    0.000000] ACPI: DSDT 1dffc134 02747 (v01   ASUS PIZZA    00001000 MSFT 0100000B)
[    0.000000] ACPI: FACS 1dfff000 00040
[    0.000000] ACPI: BOOT 1dffc030 00028 (v01 ASUS   PIZZA    42302E31 MSFT 31313031)
[    0.000000] ACPI: APIC 1dffc058 0005A (v01 ASUS   PIZZA    42302E31 MSFT 31313031)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 479MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 1dffc000
[    0.000000]   low ram: 0 - 1dffc000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0001dffc
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0001dffc
[    0.000000] On node 0 totalpages: 122763
[    0.000000] free_area_init_node: node 0, pgdat c17b11c0, node_mem_map ddc3b200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 928 pages used for memmap
[    0.000000]   Normal zone: 117852 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0xe408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 1e000000 (gap: 1e000000:e0c00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 12 pages/cpu @dc400000 s26240 r0 d22912 u4194304
[    0.000000] pcpu-alloc: s26240 r0 d22912 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 121803
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.0.0-12-generic root=UUID=64a115ee-6cf6-4d8f-b8cd-f66dd0b782af ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] allocated 1965760 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 461984k/491504k available (5329k kernel code, 29068k reserved, 2589k data, 696k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff16000 - 0xfffff000   ( 932 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xde7fc000 - 0xff7fe000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xddffc000   ( 479 MB)
[    0.000000]       .init : 0xc17bc000 - 0xc186a000   ( 696 kB)
[    0.000000]       .data : 0xc1534784 - 0xc17bbd80   (2589 kB)
[    0.000000]       .text : 0xc1000000 - 0xc1534784   (5329 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:2304 nr_irqs:256 16
[    0.000000] CPU 0 irqstacks, hard=dc008000 soft=dc00a000
[    0.000000] vt handoff: transparent VT on vt#7
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration failed
[    0.000000] TSC: Unable to calibrate against PIT
[    0.000000] TSC: using PMTIMER reference calibration
[    0.000000] Detected 2400.082 MHz processor.
[    0.012004] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.16 BogoMIPS (lpj=9600328)
[    0.012012] pid_max: default: 32768 minimum: 301
[    0.012046] Security Framework initialized
[    0.012074] AppArmor: AppArmor initialized
[    0.012078] Yama: becoming mindful.
[    0.012162] Mount-cache hash table entries: 512
[    0.012376] Initializing cgroup subsys cpuacct
[    0.012386] Initializing cgroup subsys memory
[    0.012402] Initializing cgroup subsys devices
[    0.012407] Initializing cgroup subsys freezer
[    0.012411] Initializing cgroup subsys net_cls
[    0.012415] Initializing cgroup subsys blkio
[    0.012429] Initializing cgroup subsys perf_event
[    0.012479] CPU0: Hyper-Threading is disabled
[    0.012485] mce: CPU supports 4 MCE banks
[    0.012501] CPU0: Thermal monitoring enabled (TM1)
[    0.016210] SMP alternatives: switching to UP code
[    0.030778] Freeing SMP alternatives: 24k freed
[    0.030808] ACPI: Core revision 20110413
[    0.032809] ftrace: allocating 24885 entries in 49 pages
[    0.036126] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.036398] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.078279] CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[    0.080004] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[    0.080004] ... version:                0
[    0.080004] ... bit width:              40
[    0.080004] ... generic registers:      18
[    0.080004] ... value mask:             000000ffffffffff
[    0.080004] ... max period:             0000007fffffffff
[    0.080004] ... fixed-purpose events:   0
[    0.080004] ... event mask:             000000000003ffff
[    0.080004] Brought up 1 CPUs
[    0.080004] Total of 1 processors activated (4800.16 BogoMIPS).
[    0.080004] devtmpfs: initialized
[    0.080004] PM: Registering ACPI NVS region at 1dfff000 (4096 bytes)
[    0.081636] print_constraints: dummy:
[    0.081668] Time: 17:02:59  Date: 12/29/11
[    0.081728] NET: Registered protocol family 16
[    0.081909] EISA bus registered
[    0.081925] ACPI: bus type pci registered
[    0.083865] PCI: PCI BIOS revision 2.10 entry at 0xf2430, last bus=1
[    0.083869] PCI: Using configuration type 1 for base access
[    0.085826] bio: create slab <bio-0> at 0
[    0.086635] ACPI: EC: Look up EC in DSDT
[    0.088546] ACPI: Interpreter enabled
[    0.088557] ACPI: (supports S0 S1 S3 S4 S5)
[    0.088591] ACPI: Using IOAPIC for interrupt routing
[    0.102314] ACPI: No dock devices found.
[    0.102320] HEST: Table not found.
[    0.102327] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.102434] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.102642] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.102647] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.102651] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.102655] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[    0.102659] pci_root PNP0A03:00: host bridge window [mem 0x1e000000-0xfebfffff] (ignored)
[    0.102683] pci 0000:00:00.0: [1039:0651] type 0 class 0x000600
[    0.102698] pci 0000:00:00.0: reg 10: [mem 0xec000000-0xefffffff]
[    0.102788] pci 0000:00:01.0: [1039:0001] type 1 class 0x000604
[    0.102842] pci 0000:00:02.0: [1039:0962] type 0 class 0x000601
[    0.102925] pci 0000:00:02.0: Enabling SiS 96x SMBus
[    0.102947] pci 0000:00:02.1: [1039:0016] type 0 class 0x000c05
[    0.103007] pci 0000:00:02.1: reg 20: [io  0xe600-0xe61f]
[    0.103063] pci 0000:00:02.5: [1039:5513] type 0 class 0x000101
[    0.103094] pci 0000:00:02.5: reg 10: [io  0xb800-0xb807]
[    0.103107] pci 0000:00:02.5: reg 14: [io  0xb400-0xb403]
[    0.103121] pci 0000:00:02.5: reg 18: [io  0xb000-0xb007]
[    0.103134] pci 0000:00:02.5: reg 1c: [io  0xa800-0xa803]
[    0.103147] pci 0000:00:02.5: reg 20: [io  0xa400-0xa40f]
[    0.103196] pci 0000:00:02.6: [1039:7013] type 0 class 0x000703
[    0.103219] pci 0000:00:02.6: reg 10: [io  0xa000-0xa0ff]
[    0.103233] pci 0000:00:02.6: reg 14: [io  0x9800-0x987f]
[    0.103309] pci 0000:00:02.6: supports D1 D2
[    0.103313] pci 0000:00:02.6: PME# supported from D3hot D3cold
[    0.103319] pci 0000:00:02.6: PME# disabled
[    0.103343] pci 0000:00:02.7: [1039:7012] type 0 class 0x000401
[    0.103366] pci 0000:00:02.7: reg 10: [io  0x9400-0x94ff]
[    0.103379] pci 0000:00:02.7: reg 14: [io  0x9000-0x907f]
[    0.103455] pci 0000:00:02.7: supports D1 D2
[    0.103458] pci 0000:00:02.7: PME# supported from D3hot D3cold
[    0.103464] pci 0000:00:02.7: PME# disabled
[    0.103483] pci 0000:00:03.0: [1039:7001] type 0 class 0x000c03
[    0.103501] pci 0000:00:03.0: reg 10: [mem 0xeb000000-0xeb000fff]
[    0.103583] pci 0000:00:03.1: [1039:7001] type 0 class 0x000c03
[    0.103602] pci 0000:00:03.1: reg 10: [mem 0xea800000-0xea800fff]
[    0.103689] pci 0000:00:03.3: [1039:7002] type 0 class 0x000c03
[    0.103712] pci 0000:00:03.3: reg 10: [mem 0xea000000-0xea000fff]
[    0.103796] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[    0.103802] pci 0000:00:03.3: PME# disabled
[    0.103854] pci 0000:00:12.0: [10ec:8139] type 0 class 0x000200
[    0.103878] pci 0000:00:12.0: reg 10: [io  0x8800-0x88ff]
[    0.103892] pci 0000:00:12.0: reg 14: [mem 0xe9800000-0xe98000ff]
[    0.103968] pci 0000:00:12.0: supports D1 D2
[    0.103971] pci 0000:00:12.0: PME# supported from D1 D2 D3hot D3cold
[    0.103977] pci 0000:00:12.0: PME# disabled
[    0.104019] pci 0000:00:13.0: [104c:ac44] type 2 class 0x000607
[    0.104043] pci 0000:00:13.0: reg 10: [mem 0x00000000-0x00000fff]
[    0.104069] pci 0000:00:13.0: supports D1 D2
[    0.104073] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot
[    0.104079] pci 0000:00:13.0: PME# disabled
[    0.104107] pci 0000:00:13.1: [104c:8029] type 0 class 0x000c00
[    0.104131] pci 0000:00:13.1: reg 10: [mem 0xe9000000-0xe90007ff]
[    0.104145] pci 0000:00:13.1: reg 14: [mem 0xe8800000-0xe8803fff]
[    0.104223] pci 0000:00:13.1: supports D1 D2
[    0.104226] pci 0000:00:13.1: PME# supported from D0 D1 D2 D3hot
[    0.104232] pci 0000:00:13.1: PME# disabled
[    0.104302] pci 0000:01:00.0: [1039:6325] type 0 class 0x000300
[    0.104323] pci 0000:01:00.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
[    0.104334] pci 0000:01:00.0: reg 14: [mem 0xeb800000-0xeb81ffff]
[    0.104345] pci 0000:01:00.0: reg 18: [io  0xd800-0xd87f]
[    0.104396] pci 0000:01:00.0: supports D1 D2
[    0.104440] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.104447] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.104454] pci 0000:00:01.0:   bridge window [mem 0xeb800000-0xebffffff]
[    0.104460] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xfebfffff pref]
[    0.104517] pci_bus 0000:00: on NUMA node 0
[    0.104523] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.104664] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[    0.104743]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[    0.184482] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.184586] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.184686] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[    0.184769] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.184863] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 7 10 11 12 14 15)
[    0.185289] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.185372] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.185467] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.185642] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.185646] vgaarb: loaded
[    0.185648] vgaarb: bridge control possible 0000:01:00.0
[    0.186035] SCSI subsystem initialized
[    0.186148] libata version 3.00 loaded.
[    0.186242] usbcore: registered new interface driver usbfs
[    0.186261] usbcore: registered new interface driver hub
[    0.186306] usbcore: registered new device driver usb
[    0.186446] PCI: Using ACPI for IRQ routing
[    0.186453] PCI: pci_cache_line_size set to 64 bytes
[    0.186532] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[    0.186536] reserve RAM buffer: 000000001dffc000 - 000000001fffffff
[    0.186702] NetLabel: Initializing
[    0.186706] NetLabel:  domain hash size = 128
[    0.186708] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.186725] NetLabel:  unlabeled traffic allowed by default
[    0.198662] AppArmor: AppArmor Filesystem Enabled
[    0.198723] pnp: PnP ACPI init
[    0.198754] ACPI: bus type pnp registered
[    0.198922] pnp 00:00: [mem 0x00000000-0x0009ffff]
[    0.198926] pnp 00:00: [mem 0x000f0000-0x000fffff]
[    0.198930] pnp 00:00: [mem 0x00100000-0x1dffffff]
[    0.198933] pnp 00:00: [mem 0xfec00000-0xfecfffff]
[    0.198936] pnp 00:00: [mem 0xfee00000-0xfeefffff]
[    0.199020] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.199025] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[    0.199029] system 00:00: [mem 0x00100000-0x1dffffff] could not be reserved
[    0.199034] system 00:00: [mem 0xfec00000-0xfecfffff] could not be reserved
[    0.199038] system 00:00: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.199045] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.199384] pnp 00:01: [bus 00-ff]
[    0.199389] pnp 00:01: [io  0x0cf8-0x0cff]
[    0.199393] pnp 00:01: [io  0x0000-0x0cf7 window]
[    0.199397] pnp 00:01: [io  0x0d00-0xffff window]
[    0.199401] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[    0.199404] pnp 00:01: [mem 0x000d0000-0x000dffff window]
[    0.199408] pnp 00:01: [mem 0x1e000000-0xfebfffff window]
[    0.199467] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.199523] pnp 00:02: [io  0xe400-0xe47f]
[    0.199527] pnp 00:02: [io  0xe480-0xe4ff]
[    0.199531] pnp 00:02: [io  0xe600-0xe61f]
[    0.199534] pnp 00:02: [io  0x0480-0x048f]
[    0.199537] pnp 00:02: [mem 0xffee0000-0xffefffff]
[    0.199595] system 00:02: [io  0xe400-0xe47f] has been reserved
[    0.199600] system 00:02: [io  0xe480-0xe4ff] has been reserved
[    0.199605] system 00:02: [io  0xe600-0xe61f] has been reserved
[    0.199609] system 00:02: [io  0x0480-0x048f] has been reserved
[    0.199613] system 00:02: [mem 0xffee0000-0xffefffff] has been reserved
[    0.199618] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.199649] pnp 00:03: [mem 0xfffe0000-0xffffffff]
[    0.199702] system 00:03: [mem 0xfffe0000-0xffffffff] could not be reserved
[    0.199708] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.199741] pnp 00:04: [io  0x0010-0x001f]
[    0.199745] pnp 00:04: [io  0x0022-0x002d]
[    0.199748] pnp 00:04: [io  0x0030-0x003f]
[    0.199752] pnp 00:04: [io  0x0044-0x005f]
[    0.199755] pnp 00:04: [io  0x0062-0x0063]
[    0.199758] pnp 00:04: [io  0x0065-0x006f]
[    0.199761] pnp 00:04: [io  0x0074-0x007f]
[    0.199768] pnp 00:04: [io  0x0091-0x0093]
[    0.199771] pnp 00:04: [io  0x00a2-0x00bf]
[    0.199774] pnp 00:04: [io  0x00e0-0x00ef]
[    0.199777] pnp 00:04: [io  0x04d0-0x04d1]
[    0.199837] system 00:04: [io  0x04d0-0x04d1] has been reserved
[    0.199843] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.199961] pnp 00:05: [io  0x0060]
[    0.199965] pnp 00:05: [io  0x0064]
[    0.200054] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.200076] pnp 00:06: [dma 4]
[    0.200080] pnp 00:06: [io  0x0000-0x000f]
[    0.200083] pnp 00:06: [io  0x0080-0x0090]
[    0.200086] pnp 00:06: [io  0x0094-0x009f]
[    0.200089] pnp 00:06: [io  0x00c0-0x00df]
[    0.200129] pnp 00:06: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.200149] pnp 00:07: [io  0x0070-0x0073]
[    0.200170] pnp 00:07: [irq 8]
[    0.200217] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.200232] pnp 00:08: [io  0x0061]
[    0.200275] pnp 00:08: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.200291] pnp 00:09: [io  0x00f0-0x00ff]
[    0.200298] pnp 00:09: [irq 13]
[    0.200344] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.202170] pnp 00:0a: [io  0x03f0-0x03f1]
[    0.202174] pnp 00:0a: [io  0x0295-0x0296]
[    0.202177] pnp 00:0a: [io  0x0600-0x067f]
[    0.202239] system 00:0a: [io  0x03f0-0x03f1] has been reserved
[    0.202244] system 00:0a: [io  0x0295-0x0296] has been reserved
[    0.202248] system 00:0a: [io  0x0600-0x067f] has been reserved
[    0.202253] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.203095] pnp: PnP ACPI: found 11 devices
[    0.203099] ACPI: ACPI bus type pnp unregistered
[    0.203106] PnPBIOS: Disabled by ACPI PNP
[    0.241263] Switching to clocksource acpi_pm
[    0.241298] PCI: max bus depth: 1 pci_try_num: 2
[    0.241330] pci 0000:00:13.0: BAR 15: assigned [mem 0x20000000-0x23ffffff pref]
[    0.241337] pci 0000:00:13.0: BAR 16: assigned [mem 0x24000000-0x27ffffff]
[    0.241342] pci 0000:00:13.0: BAR 0: assigned [mem 0x28000000-0x28000fff]
[    0.241351] pci 0000:00:13.0: BAR 0: set to [mem 0x28000000-0x28000fff] (PCI address [0x28000000-0x28000fff])
[    0.241356] pci 0000:00:13.0: BAR 13: assigned [io  0x1000-0x10ff]
[    0.241361] pci 0000:00:13.0: BAR 14: assigned [io  0x1400-0x14ff]
[    0.241366] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.241370] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.241378] pci 0000:00:01.0:   bridge window [mem 0xeb800000-0xebffffff]
[    0.241384] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xfebfffff pref]
[    0.241394] pci 0000:00:13.0: CardBus bridge to [bus 02-05]
[    0.241398] pci 0000:00:13.0:   bridge window [io  0x1000-0x10ff]
[    0.241405] pci 0000:00:13.0:   bridge window [io  0x1400-0x14ff]
[    0.241411] pci 0000:00:13.0:   bridge window [mem 0x20000000-0x23ffffff pref]
[    0.241418] pci 0000:00:13.0:   bridge window [mem 0x24000000-0x27ffffff]
[    0.241437] pci 0000:00:01.0: setting latency timer to 64
[    0.241445] pci 0000:00:13.0: enabling device (0000 -> 0003)
[    0.241472] pci 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.241483] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.241486] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[    0.241490] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.241494] pci_bus 0000:01: resource 1 [mem 0xeb800000-0xebffffff]
[    0.241497] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xfebfffff pref]
[    0.241502] pci_bus 0000:02: resource 0 [io  0x1000-0x10ff]
[    0.241505] pci_bus 0000:02: resource 1 [io  0x1400-0x14ff]
[    0.241509] pci_bus 0000:02: resource 2 [mem 0x20000000-0x23ffffff pref]
[    0.241512] pci_bus 0000:02: resource 3 [mem 0x24000000-0x27ffffff]
[    0.241576] NET: Registered protocol family 2
[    0.241674] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.241971] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.242075] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.242169] TCP: Hash tables configured (established 16384 bind 16384)
[    0.242172] TCP reno registered
[    0.242176] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.242187] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.242296] NET: Registered protocol family 1
[    0.242781] Switched to NOHz mode on CPU #0
[    0.272052] pci 0000:01:00.0: Boot video device
[    0.272058] PCI: CLS 32 bytes, default 64
[    0.272149] Simple Boot Flag at 0x3a set to 0x1
[    0.272564] audit: initializing netlink socket (disabled)
[    0.272583] type=2000 audit(1325178179.268:1): initialized
[    0.297797] Trying to unpack rootfs image as initramfs...
[    0.330389] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.336373] VFS: Disk quotas dquot_6.5.2
[    0.336492] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.337647] fuse init (API version 7.16)
[    0.337805] msgmni has been set to 902
[    0.352435] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.352524] io scheduler noop registered
[    0.352528] io scheduler deadline registered
[    0.352556] io scheduler cfq registered (default)
[    0.352775] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.352816] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.353033] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.353043] ACPI: Power Button [PWRB]
[    0.353116] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.353122] ACPI: Power Button [PWRF]
[    0.353158] ACPI: acpi_idle registered with cpuidle
[    0.353193] ACPI: Invalid PBLK length [5]
[    0.367151] ERST: Table is not found!
[    0.372127] isapnp: Scanning for PnP cards...
[    0.377808] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.379750] serial 0000:00:02.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.379761] serial 0000:00:02.6: PCI INT C disabled
[    0.379965] Linux agpgart interface v0.103
[    0.425510] brd: module loaded
[    0.426388] loop: module loaded
[    0.426664] pata_sis 0000:00:02.5: version 0.5.2
[    0.426706] pata_sis 0000:00:02.5: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.432120] scsi0 : pata_sis
[    0.432363] scsi1 : pata_sis
[    0.433006] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xa400 irq 14
[    0.433011] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xa408 irq 15
[    0.433634] Fixed MDIO Bus: probed
[    0.433683] PPP generic driver version 2.4.2
[    0.433806] tun: Universal TUN/TAP device driver, 1.6
[    0.433810] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.433951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.434011] ehci_hcd 0000:00:03.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[    0.434041] ehci_hcd 0000:00:03.3: EHCI Host Controller
[    0.434104] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[    0.434180] ehci_hcd 0000:00:03.3: irq 23, io mem 0xea000000
[    0.444067] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[    0.444375] hub 1-0:1.0: USB hub found
[    0.444383] hub 1-0:1.0: 6 ports detected
[    0.444495] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.444530] ohci_hcd 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 9
[    0.444559] ohci_hcd 0000:00:03.0: OHCI Host Controller
[    0.444625] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[    0.444653] ohci_hcd 0000:00:03.0: irq 9, io mem 0xeb000000
[    0.544576] hub 2-0:1.0: USB hub found
[    0.544588] hub 2-0:1.0: 3 ports detected
[    0.544711] ohci_hcd 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    0.544742] ohci_hcd 0000:00:03.1: OHCI Host Controller
[    0.544813] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[    0.544864] ohci_hcd 0000:00:03.1: irq 21, io mem 0xea800000
[    0.602337] hub 3-0:1.0: USB hub found
[    0.602349] hub 3-0:1.0: 3 ports detected
[    0.602462] uhci_hcd: USB Universal Host Controller Interface driver
[    0.602627] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.638567] ata1.00: HPA detected: current 240119615, native 240121728
[    0.638576] ata1.00: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133
[    0.638580] ata1.00: 240119615 sectors, multi 16: LBA
[    0.652858] ata1.00: configured for UDMA/133
[    0.672218] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.672476] mousedev: PS/2 mouse device common for all mice
[    0.672694] rtc_cmos 00:07: RTC can wake from S4
[    0.672836] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    0.672866] rtc0: alarms up to one month, 242 bytes nvram
[    0.673083] device-mapper: uevent: version 1.0.3
[    0.673209] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    0.673267] EISA: Probing bus 0 at eisa.0
[    0.673278] Cannot allocate resource for EISA slot 1
[    0.673303] Cannot allocate resource for EISA slot 8
[    0.673306] EISA: Detected 0 cards.
[    0.673326] cpufreq-nforce2: No nForce2 chipset.
[    0.673331] cpuidle: using governor ladder
[    0.673333] cpuidle: using governor menu
[    0.673336] EFI Variables Facility v0.08 2004-May-17
[    0.673742] TCP cubic registered
[    0.673947] NET: Registered protocol family 10
[    0.674762] NET: Registered protocol family 17
[    0.674797] Registering the dns_resolver key type
[    0.674835] Using IPI No-Shortcut mode
[    0.675003] PM: Hibernation image not present or could not be loaded.
[    0.675032] registered taskstats version 1
[    0.932040] isapnp: No Plug & Play device found
[    0.932269] scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6Y120L0   YAR4 PQ: 0 ANSI: 5
[    0.932567] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.932831] sd 0:0:0:0: [sda] 240119615 512-byte logical blocks: (122 GB/114 GiB)
[    0.932919] sd 0:0:0:0: [sda] Write Protect is off
[    0.932924] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.932962] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.978996]  sda: sda1 sda2 < sda5 >
[    0.979578] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.044131] usb 2-3: new low speed USB device number 2 using ohci_hcd
[    1.088277] ata2.01: NODEV after polling detection
[    1.096800] ata2.00: ATAPI: UJDA750 DVD/CDRW, 1.51, max UDMA/33
[    1.112758] ata2.00: configured for UDMA/33
[    1.116728] scsi 1:0:0:0: CD-ROM            MATSHITA UJDA750 DVD/CDRW 1.51 PQ: 0 ANSI: 5
[    1.120405] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.120414] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.120641] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.120760] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.170495] Freeing initrd memory: 13304k freed
[    1.201250]   Magic number: 7:980:37
[    1.201284] bdi 7:2: hash matches
[    1.201390] rtc_cmos 00:07: setting system clock to 2011-12-29 17:03:00 UTC (1325178180)
[    1.201417] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.201420] EDD information not available.
[    1.201590] Freeing unused kernel memory: 696k freed
[    1.202408] Write protecting the kernel text: 5332k
[    1.202480] Write protecting the kernel read-only data: 2188k
[    1.239236] udevd[80]: starting version 173
[    1.296075] Refined TSC clocksource calibration: 2400.085 MHz.
[    1.296088] Switching to clocksource tsc
[    1.436078] usb 3-3: new low speed USB device number 2 using ohci_hcd
[    1.470031] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.0/input/input2
[    1.470205] generic-usb 0003:046D:C50F.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:03.0-3/input0
[    1.490037] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.1/input/input3
[    1.490257] generic-usb 0003:046D:C50F.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:03.0-3/input1
[    1.490291] usbcore: registered new interface driver usbhid
[    1.490295] usbhid: USB HID core driver
[    1.550624] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    1.550667] 8139cp 0000:00:12.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    1.551565] 8139too: 8139too Fast Ethernet driver 0.9.28
[    1.551633] 8139too 0000:00:12.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.572767] 8139too 0000:00:12.0: eth0: RealTek RTL8139 at 0x8800, 00:0c:6e:c0:5d:b8, IRQ 17
[    1.579904] firewire_ohci 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.632219] firewire_ohci: Added fw-ohci device 0000:00:13.1, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[    1.669222] input: Sony Sony IR Receiver as /devices/pci0000:00/0000:00:03.1/usb3/3-3/3-3:1.0/input/input4
[    1.669488] generic-usb 0003:054C:00CD.0003: input,hiddev0,hidraw2: USB HID v1.10 Keyboard [Sony Sony IR Receiver] on usb-0000:00:03.1-3/input0
[    1.802261] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[    1.802268] EXT4-fs (sda1): write access will be enabled during recovery
[    2.039148] EXT4-fs (sda1): orphan cleanup on readonly fs
[    2.039174] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6815819
[    2.039360] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6815817
[    2.039385] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291854
[    2.039409] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291851
[    2.039429] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291842
[    2.039449] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291849
[    2.039470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291647
[    2.039492] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291839
[    2.039515] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291557
[    2.039537] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291541
[    2.039565] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291726
[    2.039587] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291563
[    2.039607] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291516
[    2.039628] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291512
[    2.039647] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291510
[    2.039667] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291494
[    2.039688] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291508
[    2.039707] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291501
[    2.039726] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291493
[    2.039746] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291582
[    2.039767] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6291843
[    2.039785] EXT4-fs (sda1): 21 orphan inodes deleted
[    2.039789] EXT4-fs (sda1): recovery complete
[    2.132209] firewire_core: created device fw0: GUID 08004603017d11af, S400
[    3.237716] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    7.196038] usb 1-3: new high speed USB device number 4 using ehci_hcd
[   15.830960] udevd[276]: starting version 173
[   15.852151] Adding 488444k swap on /dev/sda5.  Priority:-1 extents:1 across:488444k
[   15.898109] lp: driver loaded but no devices found
[   16.125982] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   16.200264] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.201939] agpgart-sis 0000:00:00.0: SiS chipset [1039/0651]
[   16.297107] agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xec000000
[   16.300996] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600
[   16.438063] type=1400 audit(1325178195.731:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=403 comm="apparmor_parser"
[   16.443251] type=1400 audit(1325178195.735:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=403 comm="apparmor_parser"
[   16.443636] type=1400 audit(1325178195.735:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=403 comm="apparmor_parser"
[   16.671128] sony_laptop: Sony Notebook Control Driver v0.6
[   16.685768] input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:09/SNY5001:00/input/input5
[   16.692822] input: Sony Vaio Jogdial as /devices/virtual/input/input6
[   16.786670] 8139too 0000:00:12.0: eth0: link down
[   16.786771] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.904183] yenta_cardbus 0000:00:13.0: CardBus bridge found [104d:815e]
[   16.904209] yenta_cardbus 0000:00:13.0: Using CSCINT to route CSC interrupts to PCI
[   16.904213] yenta_cardbus 0000:00:13.0: Routing CardBus interrupts to PCI
[   16.904220] yenta_cardbus 0000:00:13.0: TI: mfunc 0x01bd1d22, devctl 0x44
[   17.079166] usbcore: registered new interface driver uas
[   17.104211] Initializing USB Mass Storage driver...
[   17.114027] scsi2 : usb-storage 1-3:1.0
[   17.118052] usbcore: registered new interface driver usb-storage
[   17.118058] USB Mass Storage support registered.
[   17.136825] yenta_cardbus 0000:00:13.0: ISA IRQ mask 0x0cf8, PCI irq 18
[   17.136831] yenta_cardbus 0000:00:13.0: Socket status: 300000c6
[   17.654167] Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   17.878394] type=1400 audit(1325178197.171:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=634 comm="apparmor_parser"
[   17.883411] type=1400 audit(1325178197.175:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=636 comm="apparmor_parser"
[   17.889878] type=1400 audit(1325178197.183:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=636 comm="apparmor_parser"
[   17.890265] type=1400 audit(1325178197.183:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=636 comm="apparmor_parser"
[   17.946378] type=1400 audit(1325178197.239:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=639 comm="apparmor_parser"
[   17.970594] type=1400 audit(1325178197.263:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=639 comm="apparmor_parser"
[   17.993424] type=1400 audit(1325178197.287:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=639 comm="apparmor_parser"
[   18.125774] scsi 2:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[   18.128809] sd 2:0:0:0: [sdb] 3928064 512-byte logical blocks: (2.01 GB/1.87 GiB)
[   18.128859] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   18.129439] sd 2:0:0:0: [sdb] Write Protect is off
[   18.129446] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[   18.130065] sd 2:0:0:0: [sdb] No Caching mode page present
[   18.130072] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   18.133937] sd 2:0:0:0: [sdb] No Caching mode page present
[   18.133945] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   18.213428]  sdb: sdb1
[   18.216295] sd 2:0:0:0: [sdb] No Caching mode page present
[   18.216304] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   18.216311] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   18.413490] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x290-0x297 0x370-0x377
[   18.415371] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x480-0x48f
[   18.428477] init: failsafe main process (572) killed by TERM signal
[   18.436626] init: apport pre-start process (697) terminated with status 1
[   18.522502] init: apport post-stop process (727) terminated with status 1
[   18.560819]  0x4d0-0x4d7
[   18.561043] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[   18.561729] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   18.562486] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcbfff 0xf0000-0xfffff
[   18.562568] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[   18.562651] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
[   18.562735] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   18.696055] intel8x0_measure_ac97_clock: measured 54829 usecs (2638 samples)
[   18.696062] intel8x0: clocking to 48000
[   18.975204] vesafb: mode is 640x480x32, linelength=2560, pages=0
[   18.975210] vesafb: scrolling: redraw
[   18.975215] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[   18.975672] vesafb: framebuffer at 0xf0000000, mapped to 0xdec80000, using 1216k, total 1216k
[   18.975977] Console: switching to colour frame buffer device 80x30
[   18.976061] fb0: VESA VGA frame buffer device
[   19.016717] Bluetooth: Core ver 2.16
[   19.016795] NET: Registered protocol family 31
[   19.016799] Bluetooth: HCI device and connection manager initialized
[   19.016803] Bluetooth: HCI socket layer initialized
[   19.016806] Bluetooth: L2CAP socket layer initialized
[   19.019731] ppdev: user-space parallel port driver
[   19.026191] Bluetooth: SCO socket layer initialized
[   19.072111] Bluetooth: RFCOMM TTY layer initialized
[   19.072124] Bluetooth: RFCOMM socket layer initialized
[   19.072127] Bluetooth: RFCOMM ver 1.11
[   19.243124] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.243130] Bluetooth: BNEP filters: protocol multicast
[   20.070415] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   24.676896] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0

if

#14
29 Aralık 2011 - 20:36:11
@cxa1294, önemli değil. BU bir masaüstü bilgisayar değil mi? Bilgisayarın tam marka ve modelini alabilir miyim varsa? Ayrıca
Kod Seç
sudo find / -name journal-commit ne döndürüyor?

cxa1294

#15
29 Aralık 2011 - 22:52:09
bilgisayar sony vaio pcv-v100g
çıkan sonuç: /usr/lib/pm-utils/power.d/journal-commit

heartsmagic

#16
30 Aralık 2011 - 14:26:54
Kabloyu takıyorsun IP alıyor ardından bağlantı kesiliyor doğru mudur? Tam bu esnada bir dmesg çıktısı alabilir miyiz? Sen geçmişsin başlığa ancak bu esnada alınıp alınmadığından emin değilim. Kısacası önce kabloyu takacaksın, sonra bağlantı gidecek bu esnada şu komutu vereceksin:
Kod Seç
dmesg | tail > dmesg.txt
Sonrasında çıktıyı buraya geçersin. Bilgisayar modeli üzerinden bir şey çıkmıyor sanki aramalarda.
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?

Böylece yalan, dünyanın düzenine dönüştürülüyor.

cxa1294

#17
30 Aralık 2011 - 21:46:33
kusura bakmayın bu detayı atlamışım. hayır ip almıyor çünkü bu esnada bağlanmaya çalışıyorum devamlı.hatta burdaki isp şirketinin direkt ip adresine(login sayfasının ip adresine) bağlanmaya çalışıyorum bahsettiğim bağlantı sadece cihazlar arası bağlantı. tam istediğiniz gibi
bu bağlantı olduğu esnada
Kod Seç

[  137.518028] type=1400 audit(1325281448.812:24): apparmor="STATUS" operation="profile_replace" name="/usr/bin/evince-previewer" pid=1711 comm="apparmor_parser"
[  137.523182] type=1400 audit(1325281448.816:25): apparmor="STATUS" operation="profile_replace" name="/usr/bin/evince-thumbnailer" pid=1711 comm="apparmor_parser"
[  137.533740] type=1400 audit(1325281448.828:26): apparmor="STATUS" operation="profile_replace" name="/usr/lib/telepathy/mission-control-5" pid=1713 comm="apparmor_parser"
[  137.534571] type=1400 audit(1325281448.828:27): apparmor="STATUS" operation="profile_replace" name="/usr/lib/telepathy/telepathy-*" pid=1713 comm="apparmor_parser"
[  137.541352] type=1400 audit(1325281448.836:28): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1714 comm="apparmor_parser"
[  137.657236] init: apport pre-start process (1738) terminated with status 1
[  137.715840] init: apport post-stop process (1755) terminated with status 1
[  138.175592] init: plymouth-stop pre-start process (1841) terminated with status 1
[  168.205323] 8139too 0000:00:12.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[  178.928021] eth0: no IPv6 routers present




bu da tam kesilme esnasında
Kod Seç

[  316.195325] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[  316.198189] sd 3:0:0:0: [sdb] No Caching mode page present
[  316.198198] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[  316.281446]  sdb: sdb1
[  316.283798] sd 3:0:0:0: [sdb] No Caching mode page present
[  316.283806] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[  316.283811] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[  325.957127] 8139too 0000:00:12.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[  336.880039] eth0: no IPv6 routers present
[  359.712028] eth0: no IPv6 routers present

heartsmagic

#18
30 Aralık 2011 - 21:57:35
Belirli bir sorun görünmüyor dmesg kayıtlarında. Cihazlar arası bağlantı derken nasıl bir bağlantı bu?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?

Böylece yalan, dünyanın düzenine dönüştürülüyor.

cxa1294

#19
30 Aralık 2011 - 22:04:16 Son düzenlenme: 04 Ocak 2012 - 16:31:35 cerencalici
bilgisayar ve apartmandaki dağıtıcı switch arası bağlantı.
laptopum'da ubuntu 11,10 var ondan bağlanırken sıkıntı yaşamıyorum. Bu arada ilginç  bir durum.
kurulum yaptığım makinede üstte bulunması gereken menü yok. Ayrıca Ubuntu'da birçok paket kurulmadı.

heartsmagic

#20
30 Aralık 2011 - 22:45:02
Benim biraz kafam karıştı :)

Bu dizüstü değil, masaüstü mü? 11.10 mu kurulu, üstte bulunması gereken menü nedir? Birçok paket kurulmadı derken neyi kastediyoruz?
Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?

Böylece yalan, dünyanın düzenine dönüştürülüyor.

cxa1294

#21
30 Aralık 2011 - 23:00:13 Son düzenlenme: 04 Ocak 2012 - 16:33:51 cerencalici
başlıkta da belirttiğim gibi makine all in one computer. daha açık bir ifade ile klavye ve mouse haricindeki tüm hardware aksamın monitör üzerinde toplandığı masaüstü bilgisayar.
Sony vaio pgv-100g
üstteki menüden kastım. unity kurmadığımız zaman (veya kurulu da olabilir) dizinlere, yardıma vs. şeylere gnome'nin yukarıdaki menüsünden ulaşıyoruz ya.. işte yok dediğim menü odur.
birçok paket kurulmadı derken kastım şudur: sıkıntımla ilgili forumlarda dolaşıp, benzer durumlarda kullanılmış kodları ben de kullanayım derken mesela ethtool paketinin kurulu olmadığını terminalde gördüm. ayrıca bazı network tool'larının vs. programların bilgisayarımda olmadığını gördüm.
bu yüzden örneğin "negotiation" ayarıyla ilgili bir fikrim yok.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 30 Aralık 2011 - 23:03:59

Belirtmeyi unuttum makinede Ubuntu 11.10 (alternatif cd'den kurulmuş) yüklü.
yukarıdaki yazışmaları okuyabilirseniz her şey en ince ayrıntısına kadar yazılıdır.

if

#22
31 Aralık 2011 - 01:40:11 Son düzenlenme: 04 Ocak 2012 - 16:34:14 cerencalici
Aramalarıma göre "journal-commit" özelliğinin devreye girmesi bazen bilgisayarların kilitlenmesine neden oluyor. Güç yönetimiyle ilgili bir ayar bu. Masaüstünde devreye girmemesi gerek benim anladığım. O yüzden journal-commit dosyasının yerini ararttırdım. Bu özelliği devreden çıkarıp bilgisayarın kilitlenip kilitlenmediğini gözlemleyebiliriz.

Bunun dışında sda1'e dair bir sürü "ext4_orphan_cleanup" bildirimi var. Dahili bellek sağlam değil mi?

@cxa1294, grub ekranındayken Ubuntu'nun üzerine gelip e tuşuna basın, ardından gelecek ekrandaki linux satırının sonuna - "quite splash"ın hemen yanına - "acpi=off" yazıp - tırnaklar olmadan - ctrl+x ile başlattığınızda kilitlenme tekrar ediyor mu? Bir de "acpi=off" yerine "noapic" veya "nolapic" yazarak başlatıp gözlemleyin.

heartsmagic

#23
31 Aralık 2011 - 01:50:07
Ben aslında tüm iletileri okudum da, genelde de okurum da :) yine de kafam ciddi anlamda karıştı. Biraz da kopmuş gibiyim başlıktan zira @if'in söylediklerinden de bir şey anlamadım mesela :) Şimdilik aradan çıkayım.

Hayattan çıkarı olmayanların, ölümden de çıkarı olmayacaktır.
Hayatlarıyla yanlış olanların ölümleriyle doğru olmalarına imkân var mıdır?

Böylece yalan, dünyanın düzenine dönüştürülüyor.

if

#24
31 Aralık 2011 - 02:18:01 Son düzenlenme: 31 Aralık 2011 - 02:48:58 if
Benim de kafam karışık @heartsmagic:) Özetlemek gerekirse yaşanan sorunları:
1- İnternet bağlantısı
2- Bilgisayarın kilitlenmesi/donması

İnternete bağlanırken de bilgisayar donuyor,
Kod Seç
dmesg çıktısı alırken de donuyor. Birbirleriyle ilişkisini çözemedim bu sorunların. Kendilerini de çözemedim ya, neyse:)
Kod Seç
dmesg çıktısında kimi uyarılar var ama hemen hemen çoğu kişinin aldığı uyarılardan. İki şüpheli var bunlar arasında
Kod Seç
EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode
errors=remount-ro,commit=0 Bunlara Ubuntu kurulmadan önce dahili belleğin 'max blast' ile 'sıfırlanmasını' ekleyince acaba bellek kaynaklı bir durum mu var diye üzerine gitmeye çalışıyorum. Geldiğim nokta, bir önceki iletimde açıkladığım "journal-commit" özelliğinin devreye girmesi.
Yazdır
Yukarı git Sayfa1 2
Kullanıcı Eylemleri