[Çözüldü]Wireless Yapılandırma Sorunu

[MTNT]

Arkadaslar o kadar araştırmama rağmen kablosuz ağımı nasıl yapılandıracağımı bilmiyorum kablosuz ağa tıkladığım zaman wireless ağım görünmüyor ne yapmam lazım.

[if]

Gerekli çıktıları alayım: http://forum.ubuntu-tr.net/index.php?topic=28764.0

[MTNT]

lspci:

Kod Seç Genişlet


00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to AGP Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation NV34M [GeForce FX Go5200 64M] (rev a1)
02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
02:04.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02)
02:04.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller
mtnt@MTNT-PC:~$ ifconfig wlan0 up



lsusb:

Kod Seç Genişlet

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

ifconfig:

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr 00:0f:1f:0c:d1:0c 
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::20f:1fff:fe0c:d10c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:558487 errors:0 dropped:0 overruns:0 frame:0
          TX packets:304272 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:744417850 (744.4 MB)  TX bytes:34272948 (34.2 MB)
          Interrupt:17

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Sunucu
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:32 errors:0 dropped:0 overruns:0 frame:0
          TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2096 (2.0 KB)  TX bytes:2096 (2.0 KB)


iwconfig:

Kod Seç Genişlet

lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11bg  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on


iwlist scanning:

Kod Seç Genişlet

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wlan0     Failed to read scan data : Network is down

lsmod:

Kod Seç Genişlet

nls_iso8859_1          12617  0
nls_cp437              12751  0
vfat                   17308  0
fat                    55577  1 vfat
usb_storage            44173  0
uas                    17699  0
parport_pc             32114  0
ppdev                  12849  0
rfcomm                 38408  4
bnep                   17923  2
bluetooth             148839  10 rfcomm,bnep
joydev                 17393  0
snd_intel8x0           33318  3
snd_ac97_codec        106082  1 snd_intel8x0
ac97_bus               12642  1 snd_ac97_codec
snd_pcm                80435  2 snd_intel8x0,snd_ac97_codec
snd_seq_midi           13132  0
snd_rawmidi            25241  1 snd_seq_midi
arc4                   12473  2
snd_seq_midi_event     14475  1 snd_seq_midi
nvidia               7098131  26
b43legacy             131930  0
dcdbas                 14098  0
mac80211              393459  1 b43legacy
snd_seq                51567  2 snd_seq_midi,snd_seq_midi_event
pcmcia                 39822  0
snd_timer              28932  2 snd_pcm,snd_seq
snd_seq_device         14172  3 snd_seq_midi,snd_rawmidi,snd_seq
snd                    55902  13 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
psmouse                73673  0
serio_raw              12990  0
soundcore              12600  1 snd
yenta_socket           27428  0
snd_page_alloc         14115  2 snd_intel8x0,snd_pcm
cfg80211              172392  2 b43legacy,mac80211
pcmcia_rsrc            18367  1 yenta_socket
pcmcia_core            21511  3 pcmcia,yenta_socket,pcmcia_rsrc
video                  18908  0
shpchp                 32356  0
lp                     17455  0
parport                40930  3 parport_pc,ppdev,lp
b44                    31443  0
firewire_ohci          35854  0
firewire_core          56937  1 firewire_ohci
crc_itu_t              12627  1 firewire_core
ssb                    50682  2 b43legacy,b44


rfkill list:

Kod Seç Genişlet

0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no


sudo lshw -C network:

Kod Seç Genişlet

*-network:0             
       description: Ethernet interface
       product: BCM4401 100Base-T
       vendor: Broadcom Corporation
       physical id: 1
       bus info: pci@0000:02:01.0
       logical name: eth0
       version: 01
       serial: 00:0f:1f:0c:d1:0c
       size: 100Mbit/s
       capacity: 100Mbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=192.168.1.3 latency=32 link=yes multicast=yes port=twisted pair speed=100Mbit/s
       resources: irq:17 memory:faffe000-faffffff
  *-network:1
       description: Network controller
       product: BCM4306 802.11b/g Wireless LAN Controller
       vendor: Broadcom Corporation
       physical id: 2
       bus info: pci@0000:02:02.0
       version: 02
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list
       configuration: driver=b43-pci-bridge latency=32
       resources: irq:18 memory:faffc000-faffdfff
  *-network DISABLED
       description: Wireless interface
       physical id: 2
       logical name: wlan0
       serial: 00:90:4b:66:3b:49
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=b43legacy driverversion=3.0.0-14-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg


dmesg:

Kod Seç Genişlet

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.0-14-generic (buildd@palmer) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #23-Ubuntu SMP Mon Nov 21 20:34:47 UTC 2011 (Ubuntu 3.0.0-14.23-generic 3.0.9)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007ffcf800 (usable)
[    0.000000]  BIOS-e820: 000000007ffcf800 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec20000 (reserved)
[    0.000000]  BIOS-e820: 00000000feda0000 - 00000000fee10000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] NX (Execute Disable) protection: approximated by x86 segment limits
[    0.000000] DMI 2.3 present.
[    0.000000] DMI: Dell Computer Corporation Inspiron 5150                   /      , BIOS A37 09/29/2004
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x7ffcf max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 0FEDA0000 mask FFFFE0000 write-combining
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 01c00000
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 1bfb000-1c00000
[    0.000000] RAMDISK: 365f2000 - 372f1000
[    0.000000] ACPI: RSDP 000fdea0 00014 (v00 DELL  )
[    0.000000] ACPI: RSDT 7fff0000 0002C (v01 DELL    CPi R   27D4091D ASL  00000061)
[    0.000000] ACPI: FACP 7fff0400 00074 (v01 DELL    CPi R   27D4091D ASL  00000061)
[    0.000000] ACPI: DSDT 7fff1000 0220B (v01 INT430 SYSFexxx 00001001 MSFT 0100000E)
[    0.000000] ACPI: FACS 7ffff800 00040
[    0.000000] ACPI: APIC 7fff0c00 00068 (v01 DELL    CPi R   27D4091D ASL  00000047)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1159MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0007ffcf
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0007ffcf
[    0.000000] On node 0 totalpages: 524126
[    0.000000] free_area_init_node: node 0, pgdat c17b3400, node_mem_map f55f2200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2320 pages used for memmap
[    0.000000]   HighMem zone: 294593 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 12 pages/cpu @f5000000 s26240 r0 d22912 u2097152
[    0.000000] pcpu-alloc: s26240 r0 d22912 u2097152 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520030
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.0.0-14-generic root=UUID=777481c8-a608-4a0b-aecd-929769d0e90f ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] allocated 8387568 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:0007ffcf)
[    0.000000] Memory: 2048128k/2096956k available (5335k kernel code, 48376k reserved, 2592k data, 696k init, 1187652k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff16000 - 0xfffff000   ( 932 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc17bf000 - 0xc186d000   ( 696 kB)
[    0.000000]       .data : 0xc1535d84 - 0xc17be080   (2592 kB)
[    0.000000]       .text : 0xc1000000 - 0xc1535d84   (5335 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:2304 nr_irqs:512 16
[    0.000000] CPU 0 irqstacks, hard=f4408000 soft=f440a000
[    0.000000] vt handoff: transparent VT on vt#7
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3056.257 MHz processor.
[    0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6112.51 BogoMIPS (lpj=12225028)
[    0.008011] pid_max: default: 32768 minimum: 301
[    0.008042] Security Framework initialized
[    0.008071] AppArmor: AppArmor initialized
[    0.008074] Yama: becoming mindful.
[    0.008146] Mount-cache hash table entries: 512
[    0.008354] Initializing cgroup subsys cpuacct
[    0.008363] Initializing cgroup subsys memory
[    0.008374] Initializing cgroup subsys devices
[    0.008378] Initializing cgroup subsys freezer
[    0.008381] Initializing cgroup subsys net_cls
[    0.008385] Initializing cgroup subsys blkio
[    0.008397] Initializing cgroup subsys perf_event
[    0.008440] CPU: Physical Processor ID: 0
[    0.008443] CPU: Processor Core ID: 0
[    0.008448] mce: CPU supports 4 MCE banks
[    0.008461] CPU0: Thermal monitoring enabled (TM1)
[    0.010820] ACPI: Core revision 20110413
[    0.014310] ftrace: allocating 24878 entries in 49 pages
[    0.016109] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.016413] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.056634] CPU0: Mobile Intel(R) Pentium(R) 4     CPU 3.06GHz stepping 09
[    0.060003] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[    0.060003] ... version:                0
[    0.060003] ... bit width:              40
[    0.060003] ... generic registers:      18
[    0.060003] ... value mask:             000000ffffffffff
[    0.060003] ... max period:             0000007fffffffff
[    0.060003] ... fixed-purpose events:   0
[    0.060003] ... event mask:             000000000003ffff
[    0.060003] CPU 1 irqstacks, hard=f44b0000 soft=f44b2000
[    0.060003] Booting Node   0, Processors  #1 Ok.
[    0.060003] smpboot cpu 1: start_ip = 9b000
[    0.012000] Initializing CPU#1
[    0.148008] TSC synchronization [CPU#0 -> CPU#1]:
[    0.148008] Measured 31825984 cycles TSC warp between CPUs, turning off TSC clock.
[    0.148008] Marking TSC unstable due to check_tsc_sync_source failed
[    0.148034] Brought up 2 CPUs
[    0.148039] Total of 2 processors activated (12225.80 BogoMIPS).
[    0.148544] devtmpfs: initialized
[    0.150859] print_constraints: dummy:
[    0.150887] Time: 16:25:25  Date: 12/14/11
[    0.152035] NET: Registered protocol family 16
[    0.152116] Trying to unpack rootfs image as initramfs...
[    0.152346] EISA bus registered
[    0.152365] ACPI: bus type pci registered
[    0.203483] PCI: PCI BIOS revision 2.10 entry at 0xfcf1e, last bus=2
[    0.203490] PCI: Using configuration type 1 for base access
[    0.206071] bio: create slab <bio-0> at 0
[    0.207721] ACPI: EC: Look up EC in DSDT
[    0.213025] ACPI: SSDT 7fff320b 0066C (v01   DELL CPU0HTCI 00001001 MSFT 0100000E)
[    0.213045] ACPI Error: [SMIX] Namespace lookup failure, AE_ALREADY_EXISTS (20110413/dswload-337)
[    0.213057] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20110413/psloop-231)
[    0.213070] ACPI Error: Method parse/execution failed [\_PR_.CPU0._PDC] (Node f4421780), AE_ALREADY_EXISTS (20110413/psparse-536)
[    0.213087] ACPI: Marking method _PDC as Serialized because of AE_ALREADY_EXISTS error
[    0.213190] ACPI: SSDT 7fff3877 000C6 (v01   DELL CPU1HTCI 00001001 MSFT 0100000E)
[    0.213206] ACPI Error: [GETC] Namespace lookup failure, AE_ALREADY_EXISTS (20110413/dswload-337)
[    0.213217] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20110413/psloop-231)
[    0.213229] ACPI Error: Method parse/execution failed [\_PR_.CPU1._PDC] (Node f44217b0), AE_ALREADY_EXISTS (20110413/psparse-536)
[    0.213244] ACPI: Marking method _PDC as Serialized because of AE_ALREADY_EXISTS error
[    0.213495] ACPI: Interpreter enabled
[    0.213509] ACPI: (supports S0 S1 S3 S4 S5)
[    0.213572] ACPI: Using IOAPIC for interrupt routing
[    0.224125] ACPI: No dock devices found.
[    0.224132] HEST: Table not found.
[    0.224142] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.228916] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.238476] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.238484] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.238490] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.238496] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[    0.238502] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xfebfffff] (ignored)
[    0.238507] pci_root PNP0A03:00: host bridge window [mem 0xfec20000-0xfed9ffff] (ignored)
[    0.238513] pci_root PNP0A03:00: host bridge window [mem 0xfee10000-0xffafffff] (ignored)
[    0.238538] pci 0000:00:00.0: [8086:3580] type 0 class 0x000600
[    0.238552] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[    0.238634] pci 0000:00:00.1: [8086:3584] type 0 class 0x000880
[    0.238701] pci 0000:00:00.3: [8086:3585] type 0 class 0x000880
[    0.238772] pci 0000:00:01.0: [8086:3581] type 1 class 0x000604
[    0.238853] pci 0000:00:1d.0: [8086:24c2] type 0 class 0x000c03
[    0.238910] pci 0000:00:1d.0: reg 20: [io  0xbf80-0xbf9f]
[    0.238954] pci 0000:00:1d.1: [8086:24c4] type 0 class 0x000c03
[    0.239015] pci 0000:00:1d.1: reg 20: [io  0xbf40-0xbf5f]
[    0.239064] pci 0000:00:1d.2: [8086:24c7] type 0 class 0x000c03
[    0.239121] pci 0000:00:1d.2: reg 20: [io  0xbf20-0xbf3f]
[    0.239178] pci 0000:00:1d.7: [8086:24cd] type 0 class 0x000c03
[    0.239207] pci 0000:00:1d.7: reg 10: [mem 0xf4fffc00-0xf4ffffff]
[    0.239304] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.239313] pci 0000:00:1d.7: PME# disabled
[    0.239337] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[    0.239392] pci 0000:00:1f.0: [8086:24cc] type 0 class 0x000601
[    0.239486] pci 0000:00:1f.0: quirk: [io  0x1000-0x107f] claimed by ICH4 ACPI/GPIO/TCO
[    0.239494] pci 0000:00:1f.0: quirk: [io  0x1080-0x10bf] claimed by ICH4 GPIO
[    0.239516] pci 0000:00:1f.1: [8086:24ca] type 0 class 0x000101
[    0.239535] pci 0000:00:1f.1: reg 10: [io  0x01f0-0x01f7]
[    0.239550] pci 0000:00:1f.1: reg 14: [io  0x03f4-0x03f7]
[    0.239564] pci 0000:00:1f.1: reg 18: [io  0x0170-0x0177]
[    0.239578] pci 0000:00:1f.1: reg 1c: [io  0x0374-0x0377]
[    0.239592] pci 0000:00:1f.1: reg 20: [io  0xbfa0-0xbfaf]
[    0.239606] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
[    0.239657] pci 0000:00:1f.5: [8086:24c5] type 0 class 0x000401
[    0.239679] pci 0000:00:1f.5: reg 10: [io  0xb800-0xb8ff]
[    0.239692] pci 0000:00:1f.5: reg 14: [io  0xbc40-0xbc7f]
[    0.239706] pci 0000:00:1f.5: reg 18: [mem 0xf4fff800-0xf4fff9ff]
[    0.239719] pci 0000:00:1f.5: reg 1c: [mem 0xf4fff400-0xf4fff4ff]
[    0.239769] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[    0.239776] pci 0000:00:1f.5: PME# disabled
[    0.239799] pci 0000:00:1f.6: [8086:24c6] type 0 class 0x000703
[    0.239821] pci 0000:00:1f.6: reg 10: [io  0xb400-0xb4ff]
[    0.239836] pci 0000:00:1f.6: reg 14: [io  0xb080-0xb0ff]
[    0.239910] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[    0.239917] pci 0000:00:1f.6: PME# disabled
[    0.239952] pci 0000:01:00.0: [10de:0324] type 0 class 0x000300
[    0.239974] pci 0000:01:00.0: reg 10: [mem 0xfc000000-0xfcffffff]
[    0.240027] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref]
[    0.240068] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.240139] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.240146] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.240154] pci 0000:00:01.0:   bridge window [mem 0xfc000000-0xfdffffff]
[    0.240161] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff pref]
[    0.240194] pci 0000:02:01.0: [14e4:4401] type 0 class 0x000200
[    0.240216] pci 0000:02:01.0: reg 10: [mem 0xfaffe000-0xfaffffff]
[    0.240291] pci 0000:02:01.0: supports D1 D2
[    0.240296] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.240306] pci 0000:02:01.0: PME# disabled
[    0.240335] pci 0000:02:02.0: [14e4:4320] type 0 class 0x000280
[    0.240358] pci 0000:02:02.0: reg 10: [mem 0xfaffc000-0xfaffdfff]
[    0.240433] pci 0000:02:02.0: supports D1 D2
[    0.240438] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.240445] pci 0000:02:02.0: PME# disabled
[    0.240470] pci 0000:02:04.0: [104c:ac44] type 2 class 0x000607
[    0.240493] pci 0000:02:04.0: reg 10: [mem 0x00000000-0x00000fff]
[    0.240519] pci 0000:02:04.0: supports D1 D2
[    0.240523] pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.240530] pci 0000:02:04.0: PME# disabled
[    0.240554] pci 0000:02:04.1: [104c:8029] type 0 class 0x000c00
[    0.240577] pci 0000:02:04.1: reg 10: [mem 0xfaffb800-0xfaffbfff]
[    0.240592] pci 0000:02:04.1: reg 14: [mem 0xfaff4000-0xfaff7fff]
[    0.240662] pci 0000:02:04.1: supports D1 D2
[    0.240667] pci 0000:02:04.1: PME# supported from D0 D1 D2 D3hot
[    0.240674] pci 0000:02:04.1: PME# disabled
[    0.240738] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive decode)
[    0.240747] pci 0000:00:1e.0:   bridge window [io  0xd000-0xefff]
[    0.240756] pci 0000:00:1e.0:   bridge window [mem 0xf6000000-0xfbffffff]
[    0.240766] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.240771] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.240777] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[    0.240824] pci_bus 0000:03: [bus 03-06] partially hidden behind transparent bridge 0000:02 [bus 02-02]
[    0.240843] pci_bus 0000:00: on NUMA node 0
[    0.240856] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.241253] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.241363] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[    0.241545]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[    0.251886] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[    0.252065] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
[    0.252205] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
[    0.252371] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
[    0.252511] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.252659] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.252953] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.252966] vgaarb: loaded
[    0.252969] vgaarb: bridge control possible 0000:01:00.0
[    0.253478] SCSI subsystem initialized
[    0.253617] libata version 3.00 loaded.
[    0.253751] usbcore: registered new interface driver usbfs
[    0.253788] usbcore: registered new interface driver hub
[    0.253866] usbcore: registered new device driver usb
[    0.254066] PCI: Using ACPI for IRQ routing
[    0.254075] PCI: pci_cache_line_size set to 64 bytes
[    0.254200] reserve RAM buffer: 000000000009f000 - 000000000009ffff
[    0.254206] reserve RAM buffer: 000000007ffcf800 - 000000007fffffff
[    0.254452] NetLabel: Initializing
[    0.254457] NetLabel:  domain hash size = 128
[    0.254460] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.254483] NetLabel:  unlabeled traffic allowed by default
[    0.273106] AppArmor: AppArmor Filesystem Enabled
[    0.273192] pnp: PnP ACPI init
[    0.273230] ACPI: bus type pnp registered
[    0.278304] pnp 00:00: [mem 0x00000000-0x0009fbff]
[    0.278311] pnp 00:00: [mem 0x0009fc00-0x0009ffff]
[    0.278316] pnp 00:00: [mem 0x000c0000-0x000cffff]
[    0.278321] pnp 00:00: [mem 0x000e0000-0x000fffff]
[    0.278325] pnp 00:00: [mem 0x00100000-0x7ffeffff]
[    0.278330] pnp 00:00: [mem 0x7fff0000-0x7fffffff]
[    0.278335] pnp 00:00: [mem 0xfec10000-0xfec1ffff]
[    0.278339] pnp 00:00: [mem 0xfeda0000-0xfedfffff]
[    0.278344] pnp 00:00: [mem 0xffb00000-0xffbfffff]
[    0.278349] pnp 00:00: [mem 0xfec00000-0xfec0ffff]
[    0.278354] pnp 00:00: [mem 0xfee00000-0xfee0ffff]
[    0.278517] system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
[    0.278524] system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
[    0.278530] system 00:00: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.278537] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.278543] system 00:00: [mem 0x00100000-0x7ffeffff] could not be reserved
[    0.278549] system 00:00: [mem 0x7fff0000-0x7fffffff] has been reserved
[    0.278555] system 00:00: [mem 0xfec10000-0xfec1ffff] has been reserved
[    0.278561] system 00:00: [mem 0xfeda0000-0xfedfffff] has been reserved
[    0.278567] system 00:00: [mem 0xffb00000-0xffbfffff] has been reserved
[    0.278573] system 00:00: [mem 0xfec00000-0xfec0ffff] could not be reserved
[    0.278579] system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
[    0.278587] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.283444] pnp 00:01: [bus 00-ff]
[    0.283452] pnp 00:01: [io  0x0000-0x0cf7 window]
[    0.283457] pnp 00:01: [io  0x0cf8-0x0cff]
[    0.283461] pnp 00:01: [io  0x0d00-0xffff window]
[    0.283467] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[    0.283473] pnp 00:01: [mem 0x000d0000-0x000dffff window]
[    0.283478] pnp 00:01: [mem 0x80000000-0xfebfffff window]
[    0.283483] pnp 00:01: [mem 0xfec20000-0xfed9ffff window]
[    0.283488] pnp 00:01: [mem 0xfee10000-0xffafffff window]
[    0.283626] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.283668] pnp 00:02: [io  0x0092]
[    0.283673] pnp 00:02: [io  0x00b2]
[    0.283677] pnp 00:02: [io  0x0020-0x0021]
[    0.283681] pnp 00:02: [io  0x00a0-0x00a1]
[    0.283686] pnp 00:02: [irq 0 disabled]
[    0.283691] pnp 00:02: [io  0x04d0-0x04d1]
[    0.283695] pnp 00:02: [io  0x0800-0x080f]
[    0.283700] pnp 00:02: [io  0x1000-0x1005]
[    0.283704] pnp 00:02: [io  0x1008-0x100f]
[    0.283741] pnp 00:02: disabling [io  0x1000-0x1005] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.283749] pnp 00:02: disabling [io  0x1008-0x100f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.283839] system 00:02: [io  0x04d0-0x04d1] has been reserved
[    0.283845] system 00:02: [io  0x0800-0x080f] has been reserved
[    0.283853] system 00:02: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.283901] pnp 00:03: [io  0xf400-0xf4fe]
[    0.283907] pnp 00:03: [io  0x0086]
[    0.283911] pnp 00:03: [io  0x00b3]
[    0.283914] pnp 00:03: [io  0x1006-0x1007]
[    0.283919] pnp 00:03: [io  0x1010-0x105f]
[    0.283923] pnp 00:03: [io  0x1060-0x107f]
[    0.283927] pnp 00:03: [io  0x1080-0x10bf]
[    0.283932] pnp 00:03: [io  0x10c0-0x10df]
[    0.283941] pnp 00:03: [io  0x10e0-0x10ff]
[    0.283972] pnp 00:03: disabling [io  0x1006-0x1007] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.283979] pnp 00:03: disabling [io  0x1010-0x105f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.283986] pnp 00:03: disabling [io  0x1060-0x107f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.284114] system 00:03: [io  0xf400-0xf4fe] has been reserved
[    0.284121] system 00:03: [io  0x1080-0x10bf] has been reserved
[    0.284127] system 00:03: [io  0x10c0-0x10df] has been reserved
[    0.284133] system 00:03: [io  0x10e0-0x10ff] has been reserved
[    0.284140] system 00:03: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.284201] pnp 00:04: [irq 12]
[    0.284265] pnp 00:04: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.284298] pnp 00:05: [io  0x0060]
[    0.284303] pnp 00:05: [io  0x0064]
[    0.284307] pnp 00:05: [io  0x0062]
[    0.284311] pnp 00:05: [io  0x0066]
[    0.284320] pnp 00:05: [irq 1]
[    0.284377] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.284408] pnp 00:06: [io  0x0070-0x0071]
[    0.284417] pnp 00:06: [irq 8]
[    0.284423] pnp 00:06: [io  0x0072-0x0077]
[    0.284490] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.284530] pnp 00:07: [io  0x0061]
[    0.284535] pnp 00:07: [io  0x0063]
[    0.284539] pnp 00:07: [io  0x0065]
[    0.284543] pnp 00:07: [io  0x0067]
[    0.284606] pnp 00:07: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.284638] pnp 00:08: [io  0x004e-0x004f]
[    0.284642] pnp 00:08: [io  0x0900-0x097f]
[    0.284744] system 00:08: [io  0x0900-0x097f] has been reserved
[    0.284751] system 00:08: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.284790] pnp 00:09: [dma 4]
[    0.284794] pnp 00:09: [io  0x0000-0x000f]
[    0.284799] pnp 00:09: [io  0x0080-0x0085]
[    0.284803] pnp 00:09: [io  0x0087-0x008f]
[    0.284808] pnp 00:09: [io  0x00c0-0x00df]
[    0.284812] pnp 00:09: [io  0x0010-0x001f]
[    0.284816] pnp 00:09: [io  0x0090-0x0091]
[    0.284821] pnp 00:09: [io  0x0093-0x009f]
[    0.284881] pnp 00:09: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.284915] pnp 00:0a: [io  0x00f0-0x00ff]
[    0.284927] pnp 00:0a: [irq 13]
[    0.285006] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.285443] pnp: PnP ACPI: found 11 devices
[    0.285448] ACPI: ACPI bus type pnp unregistered
[    0.285457] PnPBIOS: Disabled by ACPI PNP
[    0.323800] Switching to clocksource acpi_pm
[    0.323986] Switched to NOHz mode on CPU #0
[    0.323986] PCI: max bus depth: 2 pci_try_num: 3
[    0.323986] pci 0000:00:1e.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci 0000:00:1f.1: BAR 5: assigned [mem 0x84000000-0x840003ff]
[    0.323986] pci 0000:00:1f.1: BAR 5: set to [mem 0x84000000-0x840003ff] (PCI address [0x84000000-0x840003ff])
[    0.323986] pci 0000:01:00.0: BAR 6: assigned [mem 0xfd000000-0xfd01ffff pref]
[    0.323986] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.323986] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.323847] Switched to NOHz mode on CPU #1
[    0.323986] pci 0000:00:01.0:   bridge window [mem 0xfc000000-0xfdffffff]
[    0.323986] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff pref]
[    0.323986] pci 0000:02:04.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci 0000:02:04.0: BAR 16: assigned [mem 0x88000000-0x8bffffff]
[    0.323986] pci 0000:02:04.0: BAR 0: assigned [mem 0xf6000000-0xf6000fff]
[    0.323986] pci 0000:02:04.0: BAR 0: set to [mem 0xf6000000-0xf6000fff] (PCI address [0xf6000000-0xf6000fff])
[    0.323986] pci 0000:02:04.0: BAR 13: assigned [io  0xd000-0xd0ff]
[    0.323986] pci 0000:02:04.0: BAR 14: assigned [io  0xd400-0xd4ff]
[    0.323986] pci 0000:02:04.0: CardBus bridge to [bus 03-06]
[    0.323986] pci 0000:02:04.0:   bridge window [io  0xd000-0xd0ff]
[    0.323986] pci 0000:02:04.0:   bridge window [io  0xd400-0xd4ff]
[    0.323986] pci 0000:02:04.0:   bridge window [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci 0000:02:04.0:   bridge window [mem 0x88000000-0x8bffffff]
[    0.323986] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
[    0.323986] pci 0000:00:1e.0:   bridge window [io  0xd000-0xefff]
[    0.323986] pci 0000:00:1e.0:   bridge window [mem 0xf6000000-0xfbffffff]
[    0.323986] pci 0000:00:1e.0:   bridge window [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci 0000:00:1e.0: setting latency timer to 64
[    0.323986] pci 0000:02:04.0: enabling device (0000 -> 0003)
[    0.323986] pci 0000:02:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.323986] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.323986] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[    0.323986] pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
[    0.323986] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfdffffff]
[    0.323986] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref]
[    0.323986] pci_bus 0000:02: resource 0 [io  0xd000-0xefff]
[    0.323986] pci_bus 0000:02: resource 1 [mem 0xf6000000-0xfbffffff]
[    0.323986] pci_bus 0000:02: resource 2 [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci_bus 0000:02: resource 4 [io  0x0000-0xffff]
[    0.323986] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
[    0.323986] pci_bus 0000:03: resource 0 [io  0xd000-0xd0ff]
[    0.323986] pci_bus 0000:03: resource 1 [io  0xd400-0xd4ff]
[    0.323986] pci_bus 0000:03: resource 2 [mem 0x80000000-0x83ffffff pref]
[    0.323986] pci_bus 0000:03: resource 3 [mem 0x88000000-0x8bffffff]
[    0.323986] NET: Registered protocol family 2
[    0.323986] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.323986] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.323986] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.323986] TCP: Hash tables configured (established 131072 bind 65536)
[    0.323986] TCP reno registered
[    0.323986] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.323986] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.323986] NET: Registered protocol family 1
[    0.323986] pci 0000:01:00.0: Boot video device
[    0.323986] PCI: CLS 32 bytes, default 64
[    0.324350] audit: initializing netlink socket (disabled)
[    0.324371] type=2000 audit(1323879925.320:1): initialized
[    0.359857] highmem bounce pool size: 64 pages
[    0.359868] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.380334] VFS: Disk quotas dquot_6.5.2
[    0.380489] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.382047] fuse init (API version 7.16)
[    0.382282] msgmni has been set to 1680
[    0.383167] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.383234] io scheduler noop registered
[    0.383239] io scheduler deadline registered
[    0.383273] io scheduler cfq registered (default)
[    0.383617] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.383670] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.383858] efifb: probing for efifb
[    0.383865] efifb: cannot reserve video memory at 0xa6d60
[    0.383875] efifb: framebuffer at 0xa6d60, mapped to 0xc00a6d60, using 56k, total 64k
[    0.383880] efifb: mode is 640x350x1, linelength=80, pages=1
[    0.383884] efifb: scrolling: redraw
[    0.383889] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.384160] Console: switching to colour frame buffer device 80x43
[    0.384190] fb0: EFI VGA frame buffer device
[    0.384535] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[    0.384876] ACPI: AC Adapter [AC] (on-line)
[    0.385054] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[    0.385446] ACPI: Lid Switch [LID]
[    0.385536] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.385545] ACPI: Power Button [PBTN]
[    0.385632] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[    0.385641] ACPI: Sleep Button [SBTN]
[    0.385724] ACPI: acpi_idle registered with cpuidle
[    0.389922] thermal LNXTHERM:00: registered as thermal_zone0
[    0.389927] ACPI: Thermal Zone [THM] (59 C)
[    0.389959] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[    0.390020] ERST: Table is not found!
[    0.390205] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.411533] isapnp: Scanning for PnP cards...
[    0.641731] Freeing initrd memory: 13308k freed
[    0.663885] ACPI: Battery Slot [BAT0] (battery present)
[    0.765883] isapnp: No Plug & Play device found
[    0.804334] serial 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.804342] serial 0000:00:1f.6: PCI INT B disabled
[    0.804547] Linux agpgart interface v0.103
[    0.804826] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[    0.814397] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
[    0.816272] brd: module loaded
[    0.817157] loop: module loaded
[    0.817399] ata_piix 0000:00:1f.1: version 2.13
[    0.817417] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    0.817427] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.817497] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.818012] scsi0 : ata_piix
[    0.818177] scsi1 : ata_piix
[    0.818376] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[    0.818381] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[    0.818995] Fixed MDIO Bus: probed
[    0.819031] PPP generic driver version 2.4.2
[    0.819134] tun: Universal TUN/TAP device driver, 1.6
[    0.819137] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.819277] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.819324] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[    0.819352] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.819357] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.819412] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.819452] ehci_hcd 0000:00:1d.7: debug port 1
[    0.823336] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.823364] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf4fffc00
[    0.836023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.836226] hub 1-0:1.0: USB hub found
[    0.836233] hub 1-0:1.0: 6 ports detected
[    0.836360] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.836387] uhci_hcd: USB Universal Host Controller Interface driver
[    0.836453] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.836465] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.836469] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.836532] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.836578] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[    0.836768] hub 2-0:1.0: USB hub found
[    0.836778] hub 2-0:1.0: 2 ports detected
[    0.836888] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.836897] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.836902] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.836957] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.836994] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000bf40
[    0.837177] hub 3-0:1.0: USB hub found
[    0.837184] hub 3-0:1.0: 2 ports detected
[    0.837283] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.837293] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.837297] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.837352] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.837388] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf20
[    0.837568] hub 4-0:1.0: USB hub found
[    0.837574] hub 4-0:1.0: 2 ports detected
[    0.837746] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.838063] i8042: Warning: Keylock active
[    0.840264] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.840279] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.840473] mousedev: PS/2 mouse device common for all mice
[    0.840823] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    0.840847] rtc0: alarms up to one day, 114 bytes nvram
[    0.841027] device-mapper: uevent: version 1.0.3
[    0.841177] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    0.841232] EISA: Probing bus 0 at eisa.0
[    0.841240] Cannot allocate resource for EISA slot 1
[    0.841261] EISA: Detected 0 cards.
[    0.841476] cpufreq-nforce2: No nForce2 chipset.
[    0.841480] cpuidle: using governor ladder
[    0.841483] cpuidle: using governor menu
[    0.841486] EFI Variables Facility v0.08 2004-May-17
[    0.842087] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    0.842230] TCP cubic registered
[    0.842428] NET: Registered protocol family 10
[    0.843439] NET: Registered protocol family 17
[    0.843471] Registering the dns_resolver key type
[    0.843517] Using IPI No-Shortcut mode
[    0.843662] PM: Hibernation image not present or could not be loaded.
[    0.843690] registered taskstats version 1
[    0.863217]   Magic number: 7:161:439
[    0.863340] rtc_cmos 00:06: setting system clock to 2011-12-14 16:25:26 UTC (1323879926)
[    0.863363] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.863366] EDD information not available.
[    0.980641] ata2.00: ATA-6: HTS721010G9AT00, MCZOA51A, max UDMA/100
[    0.980646] ata2.00: 195371568 sectors, multi 8: LBA48
[    0.988320] ata1.00: ATAPI: HL-DT-STCD-RW/DVD-ROM GCC-4241N, A100, max UDMA/33
[    0.996424] ata2.00: configured for UDMA/100
[    1.004159] ata1.00: configured for UDMA/33
[    1.010638] scsi 0:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4241N A100 PQ: 0 ANSI: 5
[    1.016605] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.016610] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.016791] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.016897] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.017141] scsi 1:0:0:0: Direct-Access     ATA      HTS721010G9AT00  MCZO PQ: 0 ANSI: 5
[    1.017333] sd 1:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[    1.017386] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.017461] sd 1:0:0:0: [sda] Write Protect is off
[    1.017468] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.017536] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.045308]  sda: sda1 sda2 < sda5 >
[    1.045825] sd 1:0:0:0: [sda] Attached SCSI disk
[    1.045895] Freeing unused kernel memory: 696k freed
[    1.046668] Write protecting the kernel text: 5336k
[    1.046745] Write protecting the kernel read-only data: 2192k
[    1.080593] udevd[85]: starting version 173
[    1.337819] b43-pci-bridge 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.337876] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x02, vendor 0x4243)
[    1.337887] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
[    1.337897] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x01, vendor 0x4243)
[    1.337906] ssb: Core 3 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
[    1.337915] ssb: Core 4 found: PCI (cc 0x804, rev 0x07, vendor 0x4243)
[    1.337924] ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
[    1.355725] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[    1.356905] b44 0000:02:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.376285] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x04, vendor 0x4243)
[    1.376294] ssb: Core 1 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
[    1.376300] ssb: Core 2 found: PCI (cc 0x804, rev 0x02, vendor 0x4243)
[    1.416272] ssb: Sonics Silicon Backplane found on PCI device 0000:02:01.0
[    1.416334] b44: b44.c:v2.0
[    1.416345] firewire_ohci 0000:02:04.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.437668] b44 ssb1:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0f:1f:0c:d1:0c
[    1.472112] firewire_ohci: Added fw-ohci device 0000:02:04.1, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[    1.518308] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[    1.518313] EXT4-fs (sda1): write access will be enabled during recovery
[    1.972243] firewire_core: created device fw0: GUID 344fc0002f167010, S400
[    5.766936] EXT4-fs (sda1): orphan cleanup on readonly fs
[    5.766957] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282862
[    5.767083] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282861
[    5.767111] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282809
[    5.767139] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282808
[    5.767196] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282805
[    5.767236] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 139970
[    5.767390] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 140504
[    5.767618] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282804
[    5.767684] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282628
[    5.767713] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282419
[    5.767748] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 282450
[    5.767773] EXT4-fs (sda1): 11 orphan inodes deleted
[    5.767777] EXT4-fs (sda1): recovery complete
[    5.946830] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    7.525666] udevd[280]: starting version 173
[    8.556690] intel_rng: FWH not detected
[    8.564756] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.674447] lp: driver loaded but no devices found
[    8.922049] cfg80211: Calling CRDA to update world regulatory domain
[    9.002480] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:1b/LNXVIDEO:00/input/input4
[    9.002647] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    9.080420] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    9.410762] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x254ab1, caps: 0x804713/0x0/0x0
[    9.463891] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[    9.536254] yenta_cardbus 0000:02:04.0: CardBus bridge found [1028:015f]
[    9.536281] yenta_cardbus 0000:02:04.0: Using CSCINT to route CSC interrupts to PCI
[    9.536286] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[    9.536296] yenta_cardbus 0000:02:04.0: TI: mfunc 0x00001002, devctl 0x64
[    9.768817] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0cf8, PCI irq 16
[    9.768823] yenta_cardbus 0000:02:04.0: Socket status: 30000086
[    9.768828] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[    9.768841] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [io  0xd000-0xefff]
[    9.768845] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xd000-0xefff: excluding 0xd000-0xd0ff 0xd400-0xd4ff
[    9.774851] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0xf6000000-0xfbffffff]
[    9.774857] pcmcia_socket pcmcia_socket0: cs: memory probe 0xf6000000-0xfbffffff: excluding 0xf6000000-0xf65fffff 0xfae00000-0xfb3fffff
[    9.774878] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0x80000000-0x83ffffff pref]
[    9.774883] pcmcia_socket pcmcia_socket0: cs: memory probe 0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
[    9.973690] b43legacy-phy0: Broadcom 4306 WLAN found
[    9.996053] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[    9.996080] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   10.020785] b43legacy-phy0 debug: Radio initialized
[   10.020971] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[   10.020978] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.020983] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[   10.020988] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.020994] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[   10.020999] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021004] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[   10.021009] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021014] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[   10.021019] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021033] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[   10.021038] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021050] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[   10.021055] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021059] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[   10.021065] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021069] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[   10.021075] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021081] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[   10.021086] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021091] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[   10.021096] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021101] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[   10.021107] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021111] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[   10.021117] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.021122] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[   10.021127] cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (600 mBi, 2000 mBm)
[   10.384238] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
[   10.385223] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
[   10.385664] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[   10.386036] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   10.386443] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xf0000-0xfffff
[   10.386535] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[   10.386626] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[   10.386716] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   10.394085] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[   10.394092] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394095] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[   10.394099] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394102] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[   10.394106] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394110] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[   10.394114] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394117] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[   10.394121] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394124] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[   10.394128] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394131] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[   10.394135] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394138] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[   10.394142] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394146] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[   10.394150] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394153] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[   10.394157] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394160] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[   10.394164] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394167] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[   10.394171] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394174] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[   10.394178] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394182] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[   10.394185] cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (300 mBi, 2000 mBm)
[   10.394190] cfg80211: World regulatory domain updated:
[   10.394192] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.394196] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.394200] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.394204] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.394208] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.394211] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.428426] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   10.428492] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   10.489018] nvidia: module license 'NVIDIA' taints kernel.
[   10.489024] Disabling lock debugging due to kernel taint
[   11.130749] nvidia 0000:01:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[   11.130766] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   11.131109] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.30  Thu Apr 14 08:47:14 PDT 2011
[   11.181918] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   11.183149] Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
[   11.260063] intel8x0_measure_ac97_clock: measured 54045 usecs (2604 samples)
[   11.260069] intel8x0: clocking to 48000
[   12.623690] type=1400 audit(1323879938.255:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=591 comm="apparmor_parser"
[   12.623711] type=1400 audit(1323879938.255:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=592 comm="apparmor_parser"
[   12.624922] type=1400 audit(1323879938.259:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=591 comm="apparmor_parser"
[   12.624968] type=1400 audit(1323879938.259:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=592 comm="apparmor_parser"
[   12.625626] type=1400 audit(1323879938.259:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=591 comm="apparmor_parser"
[   12.625670] type=1400 audit(1323879938.259:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=592 comm="apparmor_parser"
[   12.627321] type=1400 audit(1323879938.259:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=629 comm="apparmor_parser"
[   12.628177] type=1400 audit(1323879938.263:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=629 comm="apparmor_parser"
[   12.628675] type=1400 audit(1323879938.263:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=629 comm="apparmor_parser"
[   13.258632] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   13.875477] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   14.893251] ppdev: user-space parallel port driver
[   15.146365] type=1400 audit(1323879940.779:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=778 comm="apparmor_parser"
[   16.852810] init: failsafe main process (720) killed by TERM signal
[   16.929080] init: apport pre-start process (829) terminated with status 1
[   16.936259] init: apport post-stop process (859) terminated with status 1
[   17.808236] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.635920] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed.
[   18.635927] b43legacy-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3).
[   20.221958] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[   20.221980] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[   20.222029] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[   20.804192] b44 ssb1:0: eth0: Link is up at 100 Mbps, full duplex
[   20.804198] b44 ssb1:0: eth0: Flow control is off for TX and off for RX
[   20.815691] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.448114] Bluetooth: Core ver 2.16
[   21.448178] NET: Registered protocol family 31
[   21.448182] Bluetooth: HCI device and connection manager initialized
[   21.448188] Bluetooth: HCI socket layer initialized
[   21.448192] Bluetooth: L2CAP socket layer initialized
[   21.451289] Bluetooth: SCO socket layer initialized
[   21.548621] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   21.548629] Bluetooth: BNEP filters: protocol multicast
[   21.551462] Bluetooth: RFCOMM TTY layer initialized
[   21.551475] Bluetooth: RFCOMM socket layer initialized
[   21.551480] Bluetooth: RFCOMM ver 1.11
[   21.962304] init: plymouth-upstart-bridge main process (746) killed by TERM signal
[   22.305298] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed.
[   22.305311] b43legacy-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3).
[   24.164599] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   24.265087] EXT4-fs (sda5): re-mounted. Opts: commit=0
[   25.726202] init: plymouth-stop pre-start process (1192) terminated with status 1
[   27.307592] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   27.317948] EXT4-fs (sda5): re-mounted. Opts: commit=0
[   31.392023] eth0: no IPv6 routers present



[villain]

02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)

b43legacy sürücüsü ile çalışıyormuş.
http://linuxwireless.org/en/users/Drivers/b43#Supported_devices

Kod Seç Genişlet

sudo apt-get install firmware-b43-installer

[if]

Kod Seç Genişlet

sudo apt-get purge b43-fwcutter firmware-b43-installer firmware-b43-lpphy-installer firmware-b43legacy-installer bcmwl*
sudo apt-get install b43-fwcutter firmware-b43legacy-installer bcmwl*

[MTNT]

dediklerinizi yaptım kablosuz ağları gördü bilgisayarı kapatıp açtığğımda hiç bir ağı görmüyor kablolu olarakda ağa bağlanamıyorum ne yapmam gerekiyor kablolu ağ görünmüyor.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 14 Aralık 2011 - 23:45:46
biraz daha uğraştım ve dediklerinizi kurdukdan sonra kablosuz ağları görünüyor ağa tıklayıp wireless şifresini girdikten sonra sistem donuyor kapat aç yaptığımda ise hiç bir ağa bağlanmıyor.Sorun nedir sizce.

[if]

@MTNT,

Kod Seç Genişlet

sudo apt-get purge firmware-b43-installer dan sonra durum nedir?

Kod Seç Genişlet

dmesg | grep b43
lsmod ne diyor?

[MTNT]

dmesg | grep b43

Kod Seç Genişlet

[    1.353331] b43-pci-bridge 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   15.119032] b43legacy-phy0: Broadcom 4306 WLAN found
[   15.143349] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[   15.143372] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   15.164057] b43legacy-phy0 debug: Radio initialized
[   16.518922] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed.
[   16.518933] b43legacy-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3).


Kod Seç Genişlet

Module                  Size  Used by
nls_iso8859_1          12617  0
nls_cp437              12751  0
vfat                   17308  0
fat                    55577  1 vfat
usb_storage            44173  0
uas                    17699  0
parport_pc             32114  0
ppdev                  12849  0
rfcomm                 38408  4
bnep                   17923  2
bluetooth             148839  10 rfcomm,bnep
joydev                 17393  0
snd_intel8x0           33318  3
snd_ac97_codec        106082  1 snd_intel8x0
ac97_bus               12642  1 snd_ac97_codec
arc4                   12473  2
pcmcia                 39822  0
snd_pcm                80435  2 snd_intel8x0,snd_ac97_codec
nvidia               7098131  26
b43legacy             131930  0
snd_seq_midi           13132  0
snd_rawmidi            25241  1 snd_seq_midi
mac80211              393459  1 b43legacy
dcdbas                 14098  0
snd_seq_midi_event     14475  1 snd_seq_midi
snd_seq                51567  2 snd_seq_midi,snd_seq_midi_event
snd_timer              28932  2 snd_pcm,snd_seq
snd_seq_device         14172  3 snd_seq_midi,snd_rawmidi,snd_seq
psmouse                73673  0
snd                    55902  13 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
serio_raw              12990  0
cfg80211              172392  2 b43legacy,mac80211
yenta_socket           27428  0
pcmcia_rsrc            18367  1 yenta_socket
pcmcia_core            21511  3 pcmcia,yenta_socket,pcmcia_rsrc
soundcore              12600  1 snd
snd_page_alloc         14115  2 snd_intel8x0,snd_pcm
video                  18908  0
shpchp                 32356  0
lp                     17455  0
parport                40930  3 parport_pc,ppdev,lp
b44                    31443  0
firewire_ohci          35854  0
firewire_core          56937  1 firewire_ohci
ssb                    50682  2 b43legacy,b44
crc_itu_t              12627  1 firewire_core


[if]

@MTNT, kablo ile bağlanabiliyor musun bağlanamıyor musun? Paketleri nasıl yükledin?

[MTNT]

Kod Seç Genişlet

sudo apt-get purge firmware-b43-installer
sudo apt-get purge b43-fwcutter firmware-b43-installer firmware-b43-lpphy-installer firmware-b43legacy-installer bcmwl*
sudo apt-get install b43-fwcutter firmware-b43legacy-installer bcmwl*

bunları uçbirimde gerçekleştirdiğimde yüklendiğinde kablosuz ağlar görünüyor fakat bağlanamıyorum.Kablolu ağada bağlanamıyor sildiğimde ise bunları sadece kablolu ağlara bağlanabiliyorum.

[if]

@MTNT, eğer başka bir bilgisayar veya dağıtım kullanıyorsanız http://downloads.openwrt.org/sources/wl_apsta-3.130.20.0.o bağlantısından gerekli sürücüyü indirin. İndirilen sürücü wl_apsta-3.130.20.0.o şeklindedir. Bir şekilde Ubuntu'ya kopyalayın. Diyelimki kullanıcı ev dizini altına kopyaladınız - yani /home/kullanıcı_adı/ altındadır. Bu işlemden sonra CTRL+ALT+T ile uçbirimi açıp sırasıyla şu komutları girin:

Kod Seç Genişlet

export FIRMWARE_INSTALL_DIR="/lib/firmware"
sudo b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta-3.130.20.0.o
Sonra bilgisayarı yeniden başlatıp tekrar bağlanmayı deneyin.

[MTNT]

Kod Seç Genişlet

sudo b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta-3.130.20.0.o girince

sudo: b43-fwcutter: command not found
hatası aldım

bide şunu söylemek istiyorum bcmwl* adlı paketi kurduğumda ağda kablosuz bağlantıları görebiliyorum.Ama giriş yapmaya çalıştığımda donuyor pc.Belki bu işe yarar.

[if]

b43-fwcutter paketi yüklü görünmüyor.

Kod Seç Genişlet

dpkg -l | grep b43 ne diyor?

[MTNT]

Kod Seç Genişlet

rc  firmware-b43legacy-installer           1:014-9                                 Installer package for firmware for the b43legacy driver çıktısını aldım.

[if]

b43-fwcutter paketi yüklü değil. Yine bir şekilde bu paketi http://packages.ubuntu.com/oneiric/b43-fwcutter bağlantısından işlemci mimarisine göre indirin, Ubuntu'ya atın, yine diyelim kullanıcı ev dizininde olsun, vermeniz gerekn komut

Kod Seç Genişlet

sudo dpkg -i b43-fwcutter_014-9_i386.deb bu kurulum bittikten sonra

Kod Seç Genişlet

export FIRMWARE_INSTALL_DIR="/lib/firmware"
sudo b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta-3.130.20.0.o kısmından devam edebilirsin. Bu şekilde olmazsa bilgisayarın donma işine yükleniriz.

[MTNT]

evet sonunda oldu yaptığım şeyleride size anlatmak istiyorum.

öncelikle terminale

Kod Seç Genişlet

sudo apt-get install firmware-b43-installer

Komutunu verdim ve sizin istediğiniz b43-fwcutter paketini bağımlılık olarak yükledi.Ardından indirdiğim paketi

Kod Seç Genişlet

export FIRMWARE_INSTALL_DIR="/lib/firmware"
sudo b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta-3.130.20.0.o kodlarını yazarak kurdum ilgilendiğiniz için binlerce kez teşekkür ediyorum.Çok sağolun gerçekten.

[if]

Rica ederim @MTNT, sorunu çözmüş olmamıza ben de sevindim. Biliyorsunuz, çözülen konuların başlığına çözüldü etiketi koyuyoruz. Üyelerin bunu yapması yükümüzü hafifletiyor. Bir dahaki sefere siz koyarsınız, bu sefer ben etiketliyorum.