[Çözüldü] Intel Wireless aygıtı kurma

[LordsWords]

Kod Seç Genişlet

SIOCSIFFLAGS: Operation not possible due to RF-kill

Aynı sorun bende de var, bana da yardımcı olur musunuz?

Kod Seç Genişlet

root@ubuntu:~# rfkill unblock wlan
root@ubuntu:~# rfkill list
0: phy0: Wireless LAN
   Soft blocked: no
   Hard blocked: no
root@ubuntu:~# rfkill block wlan
root@ubuntu:~# rfkill list
0: phy0: Wireless LAN
   Soft blocked: yes
   Hard blocked: no


[if]

@LordsWords, başlıktaki önerileri denediniz mi?

[LordsWords]

@LordsWords, başlıktaki önerileri denediniz mi?

evet hepsini tektek denedim olmadı

halen hata devam ediyor..

Kod Seç Genişlet

wlan0 Intel 3945ABG iwl3945 - [phy0]SIOCSIFFLAGS: Operation not possible due to RF-kill


Kod Seç Genişlet

ioctl(SIOCSIFFLAGS) failed: Operation not possible due to RF-kill

[LordsWords]

Yardım edecek kimse yok mu=?

[cagriemer]

@LordsWords basligin hepsini okuyamadim fakat su asagidaki komutu niye verdiniz?

Kod Seç Genişlet

rfkill block wlan

Duzeltme: Simdi okumayi bitirdim.

Kod Seç Genişlet

sudo rfkill unblock all
sudo ifconfig wlan0 up

komutlarini deneyin. Yine baglanamazsaniz asagidaki komutun ciktisini paylasin lutfen.

Kod Seç Genişlet

cat /etc/network/interfaces

[LordsWords]

Kod Seç Genişlet

computer@ubuntu:~$ sudo ifconfig wlan0 up
kodunu girdim

Kod Seç Genişlet

SIOCSIFFLAGS: Operation not possible due to RF-kill
dedi
----

Kod Seç Genişlet

cat /etc/network/interfaces
kodunu girdim

Kod Seç Genişlet

# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback
dedi

[heartsmagic]

Kod Seç Genişlet

sudo rfkill unblock all komutunun çıktısı eksik, uyguladın mı uygulamadın mı?

[LordsWords]

Kod Seç Genişlet

sudo rfkill unblock all
kodunu uyguladım. herhangibi bir çıktı vermedi

[heartsmagic]

Tamam, o komut çıktı veremeyecek zaten. Ancak bizim uygulayıp uygulamadığını görmemiz gerekiyordu. Şimdi, kartını bilmiyoruz, önce ona bir bakalım:

Kod Seç Genişlet

lspci
lsusb

Ardından tekrar bir sonucu görelim:

Kod Seç Genişlet

rfkill list

[LordsWords]

Kod Seç Genişlet

computer@ubuntu:~$ lspci
kodunu girdim

Kod Seç Genişlet

00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 03)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
02:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040T PCI-E Fast Ethernet Controller (rev 12)
0a:01.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
0a:01.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02)
0a:01.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
dedi

---

Kod Seç Genişlet

computer@ubuntu:~$ lsusb
kodunu girdim

Kod Seç Genişlet

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 04f2:b008 Chicony Electronics Co., Ltd USB 2.0 Camera
Bus 005 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305
dedi

--

Kod Seç Genişlet

computer@ubuntu:~$ rfkill list
kodunu girdim

Kod Seç Genişlet

0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
dedi

[if]

@LordsWords, şu an kablosuz bağlantı yapabiliyor olmanız gerek. Ne yazılımsal ne de donanımsal olarak engellenmiş görünüyor aygıt.

[LordsWords]

çevredeki hiç bir ağı görmüyor :S

[if]

@yavuzhatip, şu durumda

Kod Seç Genişlet

ifconfig
iwconfig
iwlist scanning ne döndürüyor?

[LordsWords]

Kod Seç Genişlet

computer@ubuntu:~$ ifconfig
kodunu yazdım

Kod Seç Genişlet

eth0      Link encap:Ethernet  HWaddr 00:1e:68:7d:b9:ed 
          inet addr:192.168.1.5  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::21e:68ff:fe7d:b9ed/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:30675 errors:0 dropped:0 overruns:0 frame:0
          TX packets:23305 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:40158646 (40.1 MB)  TX bytes:2767372 (2.7 MB)
          Interrupt:17

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Sunucu
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

dedi

--------

Kod Seç Genişlet

computer@ubuntu:~$ iwconfig

yazdım

Kod Seç Genişlet

lo        no wireless extensions.

wlan0     IEEE 802.11abg  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
         
eth0      no wireless extensions.



dedi

-----

Kod Seç Genişlet

computer@ubuntu:~$ iwlist scanning

yazdım

Kod Seç Genişlet

lo        Interface doesn't support scanning.

wlan0     Failed to read scan data : Network is down

eth0      Interface doesn't support scanning.

dedi

[if]

Kod Seç Genişlet

sudo ifconfig wlan0 up komutundan sonra kablosuz bağlantılar görünüyor mu?

[LordsWords]

Kod Seç Genişlet

computer@ubuntu:~$ sudo ifconfig wlan0 up
[sudo] password for computer:
SIOCSIFFLAGS: Böyle bir aygıt yok


[if]

@LordsWord,

Kod Seç Genişlet

lsmod ne basıyor?

[LordsWords]

Kod Seç Genişlet

computer@ubuntu:~$ lsmod

Kod Seç Genişlet


Module                  Size  Used by
rfcomm                 47605  0
bnep                   18281  2
bluetooth             180168  10 rfcomm,bnep
parport_pc             32866  0
ppdev                  17113  0
lp                     17799  0
parport                46562  3 parport_pc,ppdev,lp
snd_hda_codec_conexant    62222  1
snd_hda_intel          33773  2
snd_hda_codec         118027  2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep              13668  1 snd_hda_codec
snd_pcm                97188  2 snd_hda_intel,snd_hda_codec
arc4                   12529  2
iwl3945                79045  0
snd_seq_midi           13324  0
uvcvideo               72629  0
videodev               98259  1 uvcvideo
v4l2_compat_ioctl32    17128  1 videodev
joydev                 17693  0
snd_rawmidi            30485  1 snd_seq_midi
iwl_legacy             83105  1 iwl3945
mac80211              507116  2 iwl3945,iwl_legacy
i915                  464033  3
snd_seq_midi_event     14899  1 snd_seq_midi
snd_seq                61896  2 snd_seq_midi,snd_seq_midi_event
psmouse                87603  0
serio_raw              13211  0
snd_timer              29991  2 snd_pcm,snd_seq
snd_seq_device         14540  3 snd_seq_midi,snd_rawmidi,snd_seq
cfg80211              205521  3 iwl3945,iwl_legacy,mac80211
drm_kms_helper         42558  1 i915
wmi                    19256  0
drm                   241902  4 i915,drm_kms_helper
toshiba_bluetooth      12807  0
toshiba_acpi           18306  0
sparse_keymap          13890  1 toshiba_acpi
snd                    68318  13 snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore              12680  1 snd
snd_page_alloc         18529  2 snd_hda_intel,snd_pcm
i2c_algo_bit           13423  1 i915
video                  19412  1 i915
usbhid                 47199  0
hid                    99559  1 usbhid
firewire_ohci          41000  0
firewire_core          63626  1 firewire_ohci
crc_itu_t              12707  1 firewire_core
sdhci_pci              18826  0
sdhci                  33205  1 sdhci_pci
sky2                   58918  0


[bytan]

Çıktıları nedir? Aygıtı donanımsal olarak açıp kapatmak gibi bir imkanın var mı?

Kod Seç Genişlet


dmesg
sudo lshw -C network
lsb_release -d

[LordsWords]

Donanımsal olarak bakmayı bilmiyorum..

Kod Seç Genişlet

computer@ubuntu:~$ dmesg
yazdım

Kod Seç Genişlet


[    0.229162] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.234003] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.234050] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.234093] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.234135] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.234178] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.234221] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[    0.234263] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.234305] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.234433] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.234445] vgaarb: loaded
[    0.234446] vgaarb: bridge control possible 0000:00:02.0
[    0.234553] i2c-core: driver [aat2870] using legacy suspend method
[    0.234555] i2c-core: driver [aat2870] using legacy resume method
[    0.234626] SCSI subsystem initialized
[    0.234698] libata version 3.00 loaded.
[    0.234750] usbcore: registered new interface driver usbfs
[    0.234761] usbcore: registered new interface driver hub
[    0.234793] usbcore: registered new device driver usb
[    0.234889] PCI: Using ACPI for IRQ routing
[    0.245826] PCI: pci_cache_line_size set to 64 bytes
[    0.245962] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[    0.245965] reserve RAM buffer: 00000000bf6d0000 - 00000000bfffffff
[    0.246104] NetLabel: Initializing
[    0.246106] NetLabel:  domain hash size = 128
[    0.246108] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.246122] NetLabel:  unlabeled traffic allowed by default
[    0.246181] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.246187] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.246192] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.256092] Switching to clocksource hpet
[    0.264141] AppArmor: AppArmor Filesystem Enabled
[    0.264194] pnp: PnP ACPI init
[    0.264216] ACPI: bus type pnp registered
[    0.264570] pnp 00:00: [bus 00-ff]
[    0.264573] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.264575] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.264577] pnp 00:00: [io  0x0d00-0xffff window]
[    0.264580] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.264582] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.264584] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.264586] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.264588] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.264590] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.264592] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.264594] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.264596] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.264598] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.264600] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.264602] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.264605] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.264607] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.264609] pnp 00:00: [mem 0xc0000000-0xdfffffff window]
[    0.264611] pnp 00:00: [mem 0xf0000000-0xfebfffff window]
[    0.264700] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.264770] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[    0.264772] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[    0.264774] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[    0.264776] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[    0.264778] pnp 00:01: [mem 0xe0000000-0xefffffff]
[    0.264779] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
[    0.264781] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
[    0.264783] pnp 00:01: [mem 0x0ff80000-0x0ff8ffff]
[    0.264853] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.264856] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.264859] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.264861] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.264864] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.264866] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.264869] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.264871] system 00:01: [mem 0x0ff80000-0x0ff8ffff] could not be reserved
[    0.264875] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265074] pnp 00:02: [io  0x0000-0x001f]
[    0.265076] pnp 00:02: [io  0x0081-0x0091]
[    0.265078] pnp 00:02: [io  0x0093-0x009f]
[    0.265080] pnp 00:02: [io  0x00c0-0x00df]
[    0.265082] pnp 00:02: [dma 4]
[    0.265121] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.265182] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[    0.265237] system 00:03: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.265240] system 00:03: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.265251] pnp 00:04: [io  0x00f0]
[    0.265265] pnp 00:04: [irq 13]
[    0.265305] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.265316] pnp 00:05: [io  0x002e-0x002f]
[    0.265321] pnp 00:05: [io  0x004e-0x004f]
[    0.265322] pnp 00:05: [io  0x0061]
[    0.265324] pnp 00:05: [io  0x0063]
[    0.265326] pnp 00:05: [io  0x0065]
[    0.265327] pnp 00:05: [io  0x0067]
[    0.265329] pnp 00:05: [io  0x0068]
[    0.265331] pnp 00:05: [io  0x006c]
[    0.265332] pnp 00:05: [io  0x0080]
[    0.265334] pnp 00:05: [io  0x0092]
[    0.265335] pnp 00:05: [io  0x00b2-0x00b3]
[    0.265337] pnp 00:05: [io  0x0800-0x080f]
[    0.265339] pnp 00:05: [io  0x1000-0x107f]
[    0.265341] pnp 00:05: [io  0x1180-0x11bf]
[    0.265342] pnp 00:05: [io  0xfe00]
[    0.265406] system 00:05: [io  0x0800-0x080f] has been reserved
[    0.265409] system 00:05: [io  0x1000-0x107f] has been reserved
[    0.265414] system 00:05: [io  0x1180-0x11bf] has been reserved
[    0.265417] system 00:05: [io  0xfe00] has been reserved
[    0.265420] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265428] pnp 00:06: [io  0x0070-0x0077]
[    0.265434] pnp 00:06: [irq 8]
[    0.265470] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.266060] pnp 00:07: [io  0x0060]
[    0.266062] pnp 00:07: [io  0x0064]
[    0.266068] pnp 00:07: [irq 1]
[    0.266110] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.266122] pnp 00:08: [irq 12]
[    0.266163] pnp 00:08: Plug and Play ACPI device, IDs SYN1020 SYN1000 SYN0002 PNP0f13 (active)
[    0.266182] pnp: PnP ACPI: found 9 devices
[    0.266184] ACPI: ACPI bus type pnp unregistered
[    0.272599] PCI: max bus depth: 1 pci_try_num: 2
[    0.272661] pci 0000:00:1f.3: BAR 0: assigned [mem 0xc0000000-0xc00000ff]
[    0.272667] pci 0000:00:1f.3: BAR 0: set to [mem 0xc0000000-0xc00000ff] (PCI address [0xc0000000-0xc00000ff])
[    0.272671] pci 0000:00:1c.3: BAR 14: assigned [mem 0xc0100000-0xc02fffff]
[    0.272675] pci 0000:00:1c.3: BAR 15: assigned [mem 0xc0300000-0xc04fffff 64bit pref]
[    0.272679] pci 0000:00:1c.3: BAR 13: assigned [io  0x3000-0x3fff]
[    0.272682] pci 0000:00:1c.1: BAR 15: assigned [mem 0xc0500000-0xc06fffff 64bit pref]
[    0.272686] pci 0000:00:1c.0: BAR 15: assigned [mem 0xc0700000-0xc08fffff 64bit pref]
[    0.272689] pci 0000:00:1c.0: BAR 13: assigned [io  0x4000-0x4fff]
[    0.272692] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.272696] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    0.272702] pci 0000:00:1c.0:   bridge window [mem 0xf0300000-0xf03fffff]
[    0.272707] pci 0000:00:1c.0:   bridge window [mem 0xc0700000-0xc08fffff 64bit pref]
[    0.272715] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[    0.272719] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.272725] pci 0000:00:1c.1:   bridge window [mem 0xf0200000-0xf02fffff]
[    0.272730] pci 0000:00:1c.1:   bridge window [mem 0xc0500000-0xc06fffff 64bit pref]
[    0.272737] pci 0000:00:1c.3: PCI bridge to [bus 05-05]
[    0.272741] pci 0000:00:1c.3:   bridge window [io  0x3000-0x3fff]
[    0.272747] pci 0000:00:1c.3:   bridge window [mem 0xc0100000-0xc02fffff]
[    0.272752] pci 0000:00:1c.3:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[    0.272760] pci 0000:00:1e.0: PCI bridge to [bus 0a-0a]
[    0.272766] pci 0000:00:1e.0:   bridge window [mem 0xf0400000-0xf04fffff]
[    0.272796] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.272802] pci 0000:00:1c.0: setting latency timer to 64
[    0.272815] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.272820] pci 0000:00:1c.1: setting latency timer to 64
[    0.272831] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.272836] pci 0000:00:1c.3: setting latency timer to 64
[    0.272844] pci 0000:00:1e.0: setting latency timer to 64
[    0.272848] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.272850] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.272853] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.272855] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[    0.272857] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[    0.272859] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[    0.272861] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xdfffffff]
[    0.272863] pci_bus 0000:00: resource 11 [mem 0xf0000000-0xfebfffff]
[    0.272866] pci_bus 0000:02: resource 0 [io  0x4000-0x4fff]
[    0.272868] pci_bus 0000:02: resource 1 [mem 0xf0300000-0xf03fffff]
[    0.272870] pci_bus 0000:02: resource 2 [mem 0xc0700000-0xc08fffff 64bit pref]
[    0.272872] pci_bus 0000:03: resource 0 [io  0x2000-0x2fff]
[    0.272874] pci_bus 0000:03: resource 1 [mem 0xf0200000-0xf02fffff]
[    0.272877] pci_bus 0000:03: resource 2 [mem 0xc0500000-0xc06fffff 64bit pref]
[    0.272879] pci_bus 0000:05: resource 0 [io  0x3000-0x3fff]
[    0.272881] pci_bus 0000:05: resource 1 [mem 0xc0100000-0xc02fffff]
[    0.272883] pci_bus 0000:05: resource 2 [mem 0xc0300000-0xc04fffff 64bit pref]
[    0.272886] pci_bus 0000:0a: resource 1 [mem 0xf0400000-0xf04fffff]
[    0.272888] pci_bus 0000:0a: resource 4 [io  0x0000-0x0cf7]
[    0.272890] pci_bus 0000:0a: resource 5 [io  0x0d00-0xffff]
[    0.272892] pci_bus 0000:0a: resource 6 [mem 0x000a0000-0x000bffff]
[    0.272894] pci_bus 0000:0a: resource 7 [mem 0x000d0000-0x000d3fff]
[    0.272896] pci_bus 0000:0a: resource 8 [mem 0x000d4000-0x000d7fff]
[    0.272898] pci_bus 0000:0a: resource 9 [mem 0x000d8000-0x000dbfff]
[    0.272900] pci_bus 0000:0a: resource 10 [mem 0xc0000000-0xdfffffff]
[    0.272902] pci_bus 0000:0a: resource 11 [mem 0xf0000000-0xfebfffff]
[    0.272946] NET: Registered protocol family 2
[    0.273095] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.274418] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.280357] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.281098] TCP: Hash tables configured (established 524288 bind 65536)
[    0.281100] TCP reno registered
[    0.281109] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.281177] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.281331] NET: Registered protocol family 1
[    0.281352] pci 0000:00:02.0: Boot video device
[    0.281543] PCI: CLS 64 bytes, default 64
[    0.281558] Simple Boot Flag at 0x36 set to 0x1
[    0.281928] audit: initializing netlink socket (disabled)
[    0.281938] type=2000 audit(1323459502.276:1): initialized
[    0.313880] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.336835] VFS: Disk quotas dquot_6.5.2
[    0.336895] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.337393] fuse init (API version 7.17)
[    0.337477] msgmni has been set to 5970
[    0.337781] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.337806] io scheduler noop registered
[    0.337807] io scheduler deadline registered
[    0.337839] io scheduler cfq registered (default)
[    0.337958] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.338020] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    0.338101] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.338156] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    0.338236] pcieport 0000:00:1c.3: setting latency timer to 64
[    0.338291] pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
[    0.338390] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.338415] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.338470] intel_idle: MWAIT substates: 0x3122220
[    0.338472] intel_idle: does not run on family 6 model 23
[    0.339601] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[    0.340188] ACPI: AC Adapter [ACAD] (on-line)
[    0.340263] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[    0.340299] ACPI: Lid Switch [LID]
[    0.340343] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.340348] ACPI: Power Button [PWRB]
[    0.340401] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.340404] ACPI: Power Button [PWRF]
[    0.348096] Monitor-Mwait will be used to enter C-1 state
[    0.348134] Monitor-Mwait will be used to enter C-2 state
[    0.356029] Monitor-Mwait will be used to enter C-3 state
[    0.356046] Marking TSC unstable due to TSC halts in idle
[    0.356064] ACPI: acpi_idle registered with cpuidle
[    0.360764] thermal LNXTHERM:00: registered as thermal_zone0
[    0.360766] ACPI: Thermal Zone [THRM] (46 C)
[    0.360788] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[    0.360798] ACPI: Battery Slot [BAT1] (battery absent)
[    0.360828] ERST: Table is not found!
[    0.360830] GHES: HEST is not enabled!
[    0.360937] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.361086] ACPI: Battery Slot [BAT1] (battery absent)
[    0.443676] Freeing initrd memory: 13676k freed
[    0.508408] Linux agpgart interface v0.103
[    0.508488] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[    0.508573] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[    0.509582] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[    0.509722] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    0.511143] brd: module loaded
[    0.511887] loop: module loaded
[    0.512074] ata_piix 0000:00:1f.1: version 2.13
[    0.512088] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    0.512122] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.512434] scsi0 : ata_piix
[    0.512512] scsi1 : ata_piix
[    0.512840] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    0.512842] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    0.512865] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.512871] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    0.512890] ata2: port disabled--ignoring
[    0.668053] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.668332] scsi2 : ata_piix
[    0.668405] scsi3 : ata_piix
[    0.668697] ata3: SATA max UDMA/133 cmd 0x1c00 ctl 0x18f4 bmdma 0x18e0 irq 19
[    0.668704] ata4: SATA max UDMA/133 cmd 0x18f8 ctl 0x18f0 bmdma 0x18e8 irq 19
[    0.669050] Fixed MDIO Bus: probed
[    0.669070] tun: Universal TUN/TAP device driver, 1.6
[    0.669072] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.669117] arcnet loaded.
[    0.669120] PPP generic driver version 2.4.2
[    0.669216] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.669238] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.669254] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    0.669257] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    0.669300] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.669330] ehci_hcd 0000:00:1a.7: debug port 1
[    0.673204] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    0.673218] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf0704000
[    0.676450] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T40N, JT03, max UDMA/33
[    0.688018] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.688139] hub 1-0:1.0: USB hub found
[    0.688143] hub 1-0:1.0: 4 ports detected
[    0.688215] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.688225] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.688229] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.688278] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.688305] ehci_hcd 0000:00:1d.7: debug port 1
[    0.692188] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    0.692407] ata1.00: configured for UDMA/33
[    0.692413] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0704400
[    0.697845] scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T40N  JT03 PQ: 0 ANSI: 5
[    0.702823] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    0.702825] cdrom: Uniform CD-ROM driver Revision: 3.20
[    0.702927] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    0.703043] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    0.708018] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.708140] hub 2-0:1.0: USB hub found
[    0.708145] hub 2-0:1.0: 6 ports detected
[    0.708225] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.708238] uhci_hcd: USB Universal Host Controller Interface driver
[    0.708255] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.708262] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    0.708265] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.708306] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.708345] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[    0.708465] hub 3-0:1.0: USB hub found
[    0.708469] hub 3-0:1.0: 2 ports detected
[    0.708541] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    0.708547] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    0.708550] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.708590] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.708625] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[    0.708745] hub 4-0:1.0: USB hub found
[    0.708749] hub 4-0:1.0: 2 ports detected
[    0.708816] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.708822] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.708825] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.708869] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    0.708895] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[    0.709021] hub 5-0:1.0: USB hub found
[    0.709024] hub 5-0:1.0: 2 ports detected
[    0.709089] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.709095] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.709098] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.709141] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    0.709170] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[    0.709287] hub 6-0:1.0: USB hub found
[    0.709291] hub 6-0:1.0: 2 ports detected
[    0.709355] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.709361] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.709364] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.709403] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    0.709430] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[    0.709549] hub 7-0:1.0: USB hub found
[    0.709553] hub 7-0:1.0: 2 ports detected
[    0.709669] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.712515] i8042: Detected active multiplexing controller, rev 1.1
[    0.713629] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.713634] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.713662] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.713687] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.713711] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.713829] mousedev: PS/2 mouse device common for all mice
[    0.714010] rtc_cmos 00:06: RTC can wake from S4
[    0.714126] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    0.714156] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.714232] device-mapper: uevent: version 1.0.3
[    0.714299] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    0.714360] cpuidle: using governor ladder
[    0.714443] cpuidle: using governor menu
[    0.714445] EFI Variables Facility v0.08 2004-May-17
[    0.714680] TCP cubic registered
[    0.714782] NET: Registered protocol family 10
[    0.715192] NET: Registered protocol family 17
[    0.715205] Registering the dns_resolver key type
[    0.715348] PM: Hibernation image not present or could not be loaded.
[    0.715360] registered taskstats version 1
[    0.731912]   Magic number: 7:310:647
[    0.731936] scsi_host host1: hash matches
[    0.731938] scsi host1: hash matches
[    0.732015] processor LNXCPU:00: hash matches
[    0.732074] rtc_cmos 00:06: setting system clock to 2011-12-09 19:38:23 UTC (1323459503)
[    0.732549] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.732551] EDD information not available.
[    0.743480] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.132264] usb 2-3: new high-speed USB device number 3 using ehci_hcd
[    1.464288] ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.464310] ata3.01: SATA link down (SStatus 0 SControl 310)
[    1.516198] usb 5-2: new full-speed USB device number 2 using uhci_hcd
[    1.528464] ata3.00: ATA-8: TOSHIBA MK3252GSX, LV010M, max UDMA/100
[    1.528470] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.544631] ata3.00: configured for UDMA/100
[    1.544865] scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA MK3252GS LV01 PQ: 0 ANSI: 5
[    1.545047] sd 2:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.545050] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    1.545133] sd 2:0:0:0: [sda] Write Protect is off
[    1.545136] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.545220] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.599677]  sda: sda1 sda2 sda3
[    1.600114] sd 2:0:0:0: [sda] Attached SCSI disk
[    2.016251] ata4.01: failed to resume link (SControl 0)
[    2.027411] ata4.00: SATA link down (SStatus 0 SControl 300)
[    2.027434] ata4.01: SATA link down (SStatus 0 SControl 0)
[    2.028938] Freeing unused kernel memory: 916k freed
[    2.029218] Write protecting the kernel read-only data: 12288k
[    2.034195] Freeing unused kernel memory: 1648k freed
[    2.038313] Freeing unused kernel memory: 1208k freed
[    2.053593] udevd[97]: starting version 175
[    2.115510] sky2: driver version 1.30
[    2.115553] sky2 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    2.115569] sky2 0000:03:00.0: setting latency timer to 64
[    2.115605] sky2 0000:03:00.0: Yukon-2 FE+ chip revision 0
[    2.115715] sky2 0000:03:00.0: irq 43 for MSI/MSI-X
[    2.116230] sky2 0000:03:00.0: eth0: addr 00:1e:68:7d:b9:ed
[    2.143191] sdhci: Secure Digital Host Controller Interface driver
[    2.143194] sdhci: Copyright(c) Pierre Ossman
[    2.143475] sdhci-pci 0000:0a:01.2: SDHCI controller found [1217:7120] (rev 2)
[    2.143495] sdhci-pci 0000:0a:01.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.143541] mmc0: no vmmc regulator found
[    2.143572] Registered led device: mmc0::
[    2.146725] mmc0: SDHCI controller on PCI [0000:0a:01.2] using DMA
[    2.147410] firewire_ohci 0000:0a:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.158844] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input4
[    2.160666] generic-usb 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2/input0
[    2.165056] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input5
[    2.165314] generic-usb 0003:046D:C52F.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-2/input1
[    2.165333] usbcore: registered new interface driver usbhid
[    2.165335] usbhid: USB HID core driver
[    2.200106] firewire_ohci: Added fw-ohci device 0000:0a:01.0, OHCI v1.10, 8 IR + 8 IT contexts, quirks 0x10
[    2.700235] firewire_core: created device fw0: GUID 001b240001047ebe, S400
[    3.073272] kjournald starting.  Commit interval 5 seconds
[    3.073383] EXT3-fs (loop0): mounted filesystem with ordered data mode
[    5.052365] Monitor-Mwait will be used to enter C-3 state
[   17.832258] udevd[363]: starting version 175
[   17.953303] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19
[   17.954509] input: Toshiba input device as /devices/virtual/input/input6
[   17.957803] Registered led device: toshiba::illumination
[   17.960261] toshiba_bluetooth: Detected Toshiba ACPI Bluetooth device - installing RFKill handler
[   17.965211] [drm] Initialized drm 1.1.0 20060810
[   17.966431] wmi: Mapper loaded
[   17.990855] cfg80211: Calling CRDA to update world regulatory domain
[   18.094574] type=1400 audit(1323452320.859:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=532 comm="apparmor_parser"
[   18.094950] type=1400 audit(1323452320.859:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=532 comm="apparmor_parser"
[   18.095177] type=1400 audit(1323452320.859:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=532 comm="apparmor_parser"
[   18.234605] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.234611] i915 0000:00:02.0: setting latency timer to 64
[   18.313547] i915 0000:00:02.0: irq 44 for MSI/MSI-X
[   18.313554] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   18.313555] [drm] Driver supports precise vblank timestamp query.
[   18.313598] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   18.323917] Linux video capture interface: v2.00
[   18.324512] uvcvideo: Found UVC 1.00 device Chicony USB 2.0 Camera (04f2:b008)
[   18.353582] input: Chicony USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/2-3:1.0/input/input7
[   18.353851] usbcore: registered new interface driver uvcvideo
[   18.353854] USB Video Class driver (1.1.1)
[   18.368665] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
[   18.368668] iwl3945: Copyright(c) 2003-2011 Intel Corporation
[   18.368749] iwl3945 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.368763] iwl3945 0000:02:00.0: setting latency timer to 64
[   18.426070] fixme: max PWM is zero.
[   18.426198] iwl3945 0000:02:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[   18.426202] iwl3945 0000:02:00.0: Detected Intel Wireless WiFi Link 3945ABG
[   18.426352] iwl3945 0000:02:00.0: irq 45 for MSI/MSI-X
[   18.426567] Registered led device: phy0-led
[   18.426596] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[   18.457531] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[   18.457535] cfg80211: World regulatory domain updated:
[   18.457536] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   18.457539] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.457541] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   18.457544] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   18.457546] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.457549] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.457990] ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
[   18.656453] [drm] initialized overlay support
[   18.801970] fbcon: inteldrmfb (fb0) is primary device
[   18.802592] Console: switching to colour frame buffer device 160x50
[   18.802617] fb0: inteldrmfb frame buffer device
[   18.802619] drm: registered panic notifier
[   18.827448] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.0, id: 0x1e0b1, caps: 0xd04711/0xa00000/0x20000
[   18.827454] psmouse serio4: synaptics: Toshiba Satellite A300 detected, limiting rate to 40pps.
[   18.862616] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[   18.872782] acpi device:02: registered as cooling_device2
[   18.880818] acpi device:03: registered as cooling_device3
[   18.890156] acpi device:04: registered as cooling_device4
[   18.896782] acpi device:05: registered as cooling_device5
[   18.905185] acpi device:06: registered as cooling_device6
[   18.905258] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input9
[   18.905606] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   18.905674] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   18.905732] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   18.905802] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[   18.905833] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   18.942332] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   18.942500] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   18.988303] Adding 262140k swap on /host/ubuntu/disks/swap.disk.  Priority:-1 extents:1 across:262140k
[   19.022011] EXT3-fs (loop0): using internal journal
[   19.215287] lp: driver loaded but no devices found
[   19.220707] ppdev: user-space parallel port driver
[   19.236774] type=1400 audit(1323452322.003:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=793 comm="apparmor_parser"
[   19.237231] type=1400 audit(1323452322.003:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=793 comm="apparmor_parser"
[   19.449117] iwl3945 0000:02:00.0: loaded firmware version 15.32.2.9
[   19.449281] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch
[   19.473231] sky2 0000:03:00.0: eth0: enabling interface
[   19.473728] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.510737] type=1400 audit(1323452322.275:7): apparmor="DENIED" operation="open" parent=1 profile="/usr/sbin/cupsd" name="/etc/pkcs11/modules/" pid=794 comm="cupsd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[   19.593995] type=1400 audit(1323452322.359:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=809 comm="apparmor_parser"
[   19.594522] type=1400 audit(1323452322.359:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=808 comm="apparmor_parser"
[   19.595189] type=1400 audit(1323452322.359:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=809 comm="apparmor_parser"
[   19.595418] type=1400 audit(1323452322.359:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=809 comm="apparmor_parser"
[   19.605111] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch
[   19.605262] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch
[   19.727889] init: failsafe main process (731) killed by TERM signal
[   19.756758] Bluetooth: Core ver 2.16
[   19.756785] NET: Registered protocol family 31
[   19.756787] Bluetooth: HCI device and connection manager initialized
[   19.756789] Bluetooth: HCI socket layer initialized
[   19.756792] Bluetooth: L2CAP socket layer initialized
[   19.756964] Bluetooth: SCO socket layer initialized
[   19.758657] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.758661] Bluetooth: BNEP filters: protocol multicast
[   19.765568] Bluetooth: RFCOMM TTY layer initialized
[   19.765574] Bluetooth: RFCOMM socket layer initialized
[   19.765575] Bluetooth: RFCOMM ver 1.11
[   21.073878] sky2 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control both
[   21.074290] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.233154] init: plymouth-stop pre-start process (1123) terminated with status 1
[   31.384223] eth0: no IPv6 routers present
[   52.595133] audit_printk_skb: 24 callbacks suppressed
[   52.595137] type=1400 audit(1323452357.205:20): apparmor="DENIED" operation="mkdir" parent=1646 profile="/usr/lib/telepathy/mission-control-5" name="/home/computer/.local/share/telepathy/" pid=1647 comm="mission-control" requested_mask="c" denied_mask="c" fsuid=1000 ouid=1000
[   52.891564] type=1400 audit(1323452357.501:21): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/mission-control-5" name="/home/computer/.cache/dconf/user" pid=1647 comm="mission-control" requested_mask="rwc" denied_mask="rwc" fsuid=1000 ouid=1000
[ 3874.723142] sky2 0000:03:00.0: eth0: Link is down
[ 3876.337629] sky2 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 4082.070696] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch
[ 4271.003946] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch


dedi

-----

Kod Seç Genişlet

computer@ubuntu:~$ sudo lshw -C network
yazdım

Kod Seç Genişlet

computer@ubuntu:~$ sudo lshw -C network
  *-network DISABLED     
       description: Wireless interface
       product: PRO/Wireless 3945ABG [Golan] Network Connection
       vendor: Intel Corporation
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: wlan0
       version: 02
       serial: 00:1f:3c:78:2b:64
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
       configuration: broadcast=yes driver=iwl3945 driverversion=3.2.0-2-generic firmware=15.32.2.9 latency=0 link=no multicast=yes wireless=IEEE 802.11abg
       resources: irq:45 memory:f0300000-f0300fff
  *-network
       description: Ethernet interface
       product: 88E8040T PCI-E Fast Ethernet Controller
       vendor: Marvell Technology Group Ltd.
       physical id: 0
       bus info: pci@0000:03:00.0
       logical name: eth0
       version: 12
       serial: 00:1e:68:7d:b9:ed
       size: 100Mbit/s
       capacity: 100Mbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.5 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
       resources: irq:43 memory:f0200000-f0203fff ioport:2000(size=256)

dedi.

----------

Kod Seç Genişlet

computer@ubuntu:~$ lsb_release -d
yazdım

Kod Seç Genişlet


Description: Ubuntu precise (development branch)

dedi

[bytan]

Kod Seç Genişlet


[   19.449281] iwl3945 0000:02:00.0: Radio disabled by HW RF Kill switch

Kullandığın makinanda bir şekilde donanımsal olarak kablosuz kartı açıp kapatmaya yarayan bir düğme/çentik varsa bunu araştırıp öğrenmelisin. Buna göre de kontrollere devam edebilirsin.


Ayrıca;

Kullandığın sistem henüz geliştirilme aşamasında. Kartına ait araştırma yaparken önceki sürümlerde yeni çekirdek güncellemeleriyle sorunun yaşandığı ve daha sonra yine güncellemelerle çözüldüğüne dair böcek girdilerine denk geldim.

Konuyu da alfa bölümümüze taşıyalım.

[LordsWords]

Teşekkürler Sorun u Sayenizde Çözdüm..

Fn+F8 ve wireless ı ''On'' konumuna getirdim. Sorun Çözüldü.

Emeği Geçen Arkadaşlar Hepinize Teşekkür Ederim..

[alquirel]

Çözüldüğüne göre ilk iletinizin başlığına [Çözüldü] ifadesi ekleyebilirsiniz.

Şimdilik benden olsun