GT-U8000-RH Gigabyte USB Dijital+Analog TV Kartı

[mustafaceylan]

bu tv kartını ubuntu 10.04 te nasıl çalıştırabilirim.heryere baktım ama hiç bir şey bulamadım.bulduklarımda işe yaramadı.kullandığım bilgisayarda asus f3jc laptop.yardım ederseniz sevinirim.

[heartsmagic]

TV kartı sahibi arkadaşlar çipseti görürlerse belki yardımcı olabilirler:

Kod Seç Genişlet

lsusb

[mustafaceylan]

lsusb kodu sonucu aşağıdadır.

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 0b05:1712 ASUSTek Computer, Inc. BT-183 Bluetooth 2.0+EDR adapter
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c019 Logitech, Inc. Optical Tilt Wheel Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 005: ID 1044:7002 Chu Yuen Enterprise Co., Ltd
Bus 001 Device 004: ID 05e1:0501 Syntek Semiconductor Co., Ltd DC-1125 Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

[eribol]

Kaffeine veya alternatiflerini denediniz mi? İngilizceniz varsa http://ubuntuforums.org/showthread.php?t=853987 buyrun. Çözülmüş bu başlıkta.

[mustafaceylan]

evet denedim.kaffeine kurdum.kanal arattırıyorum bulmuyor hiçbirşey.sanırım kaffein kartı görmüyor.dibcom 7000pc yazıyor device ye girince kaffeinde.ayarı nasıl yapılır anlatırsanız deneyebilirim.

[eribol]

http://www.linuxtv.org/wiki/index.php/Gigabyte_U8000-RH burada adım adım anlatılmış. Az bir ingilizce ile yapılabilir sanırım.

Kod Seç Genişlet

dmesgçıktısınında;

usb 5-2: new high speed USB device using ehci_hcd and address 2

böyle bir satır olacak tv kartınız için. Sonrasında söylenen komutları takip edebilirsiniz.

[mustafaceylan]

dmesg çıktısı bu

Kod Seç Genişlet


[    0.232597] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.232612] NetLabel:  unlabeled traffic allowed by default
[    0.232650] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.232657] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.236236] Switching to clocksource tsc
[    0.238488] AppArmor: AppArmor Filesystem Enabled
[    0.238505] pnp: PnP ACPI init
[    0.238523] ACPI: bus type pnp registered
[    0.241054] pnp: PnP ACPI: found 13 devices
[    0.241057] ACPI: ACPI bus type pnp unregistered
[    0.241062] PnPBIOS: Disabled by ACPI PNP
[    0.241076] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.241087] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.241091] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.241094] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.241098] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.241101] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[    0.241105] system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
[    0.241108] system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
[    0.241112] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
[    0.241115] system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
[    0.241123] system 00:0a: ioport range 0x250-0x253 has been reserved
[    0.241126] system 00:0a: ioport range 0x256-0x25f has been reserved
[    0.241129] system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.241133] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.241136] system 00:0a: iomem range 0xfec10000-0xfec17fff has been reserved
[    0.241140] system 00:0a: iomem range 0xfec18000-0xfec1ffff has been reserved
[    0.241143] system 00:0a: iomem range 0xfec20000-0xfec27fff has been reserved
[    0.241150] system 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
[    0.241157] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[    0.241160] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[    0.241163] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[    0.241167] system 00:0c: iomem range 0x100000-0x3fffffff could not be reserved
[    0.275984] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.275988] pci 0000:00:01.0:   IO window: disabled
[    0.275993] pci 0000:00:01.0:   MEM window: 0xf9f00000-0xfdffffff
[    0.275998] pci 0000:00:01.0:   PREFETCH window: 0x000000bdf00000-0x000000ddefffff
[    0.276004] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.276008] pci 0000:00:1c.0:   IO window: 0xc000-0xcfff
[    0.276016] pci 0000:00:1c.0:   MEM window: 0xfe000000-0xfe0fffff
[    0.276022] pci 0000:00:1c.0:   PREFETCH window: 0x00000040000000-0x000000401fffff
[    0.276031] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[    0.276035] pci 0000:00:1c.1:   IO window: 0x1000-0x1fff
[    0.276043] pci 0000:00:1c.1:   MEM window: 0xfe100000-0xfe1fffff
[    0.276048] pci 0000:00:1c.1:   PREFETCH window: 0x00000040200000-0x000000403fffff
[    0.276058] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[    0.276062] pci 0000:00:1c.2:   IO window: 0xd000-0xdfff
[    0.276070] pci 0000:00:1c.2:   MEM window: 0xfe200000-0xfe9fffff
[    0.276076] pci 0000:00:1c.2:   PREFETCH window: 0x000000ddf00000-0x000000dfefffff
[    0.276085] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
[    0.276087] pci 0000:00:1e.0:   IO window: disabled
[    0.276095] pci 0000:00:1e.0:   MEM window: 0xfea00000-0xfeafffff
[    0.276100] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.276126]   alloc irq_desc for 16 on node -1
[    0.276128]   alloc kstat_irqs on node -1
[    0.276137] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.276143] pci 0000:00:01.0: setting latency timer to 64
[    0.276154] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.276160] pci 0000:00:1c.0: setting latency timer to 64
[    0.276172] pci 0000:00:1c.1: enabling device (0106 -> 0107)
[    0.276176]   alloc irq_desc for 17 on node -1
[    0.276178]   alloc kstat_irqs on node -1
[    0.276182] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.276188] pci 0000:00:1c.1: setting latency timer to 64
[    0.276199]   alloc irq_desc for 18 on node -1
[    0.276201]   alloc kstat_irqs on node -1
[    0.276205] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.276211] pci 0000:00:1c.2: setting latency timer to 64
[    0.276221] pci 0000:00:1e.0: setting latency timer to 64
[    0.276226] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.276229] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.276233] pci_bus 0000:01: resource 1 mem: [0xf9f00000-0xfdffffff]
[    0.276236] pci_bus 0000:01: resource 2 pref mem [0xbdf00000-0xddefffff]
[    0.276239] pci_bus 0000:02: resource 0 io:  [0xc000-0xcfff]
[    0.276241] pci_bus 0000:02: resource 1 mem: [0xfe000000-0xfe0fffff]
[    0.276244] pci_bus 0000:02: resource 2 pref mem [0x40000000-0x401fffff]
[    0.276247] pci_bus 0000:03: resource 0 io:  [0x1000-0x1fff]
[    0.276250] pci_bus 0000:03: resource 1 mem: [0xfe100000-0xfe1fffff]
[    0.276253] pci_bus 0000:03: resource 2 pref mem [0x40200000-0x403fffff]
[    0.276256] pci_bus 0000:04: resource 0 io:  [0xd000-0xdfff]
[    0.276259] pci_bus 0000:04: resource 1 mem: [0xfe200000-0xfe9fffff]
[    0.276261] pci_bus 0000:04: resource 2 pref mem [0xddf00000-0xdfefffff]
[    0.276265] pci_bus 0000:06: resource 1 mem: [0xfea00000-0xfeafffff]
[    0.276267] pci_bus 0000:06: resource 3 io:  [0x00-0xffff]
[    0.276270] pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
[    0.276317] NET: Registered protocol family 2
[    0.276444] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.276832] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.277444] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.277738] TCP: Hash tables configured (established 131072 bind 65536)
[    0.277741] TCP reno registered
[    0.277848] NET: Registered protocol family 1
[    0.278002] pci 0000:01:00.0: Boot video device
[    0.278047] Simple Boot Flag at 0x52 set to 0x1
[    0.278255] cpufreq-nforce2: No nForce2 chipset.
[    0.278293] Scanning for low [s]memory[/s] corruption every 60 seconds
[    0.278422] audit: initializing netlink socket (disabled)
[    0.278435] type=2000 audit(1275377576.275:1): initialized
[    0.289447] highmem bounce pool size: 64 pages
[    0.289456] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.291208] VFS: Disk quotas dquot_6.5.2
[    0.291295] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.291955] fuse init (API version 7.13)
[    0.292051] msgmni has been set to 1716
[    0.292299] alg: No test for stdrng (krng)
[    0.292358] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.292362] io scheduler noop registered
[    0.292364] io scheduler anticipatory registered
[    0.292367] io scheduler deadline registered
[    0.292409] io scheduler cfq registered (default)
[    0.292586]   alloc irq_desc for 24 on node -1
[    0.292589]   alloc kstat_irqs on node -1
[    0.292599] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[    0.292607] pcieport 0000:00:01.0: setting latency timer to 64
[    0.292742]   alloc irq_desc for 25 on node -1
[    0.292744]   alloc kstat_irqs on node -1
[    0.292753] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[    0.292765] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.292933]   alloc irq_desc for 26 on node -1
[    0.292935]   alloc kstat_irqs on node -1
[    0.292945] pcieport 0000:00:1c.1: irq 26 for MSI/MSI-X
[    0.292956] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.293125]   alloc irq_desc for 27 on node -1
[    0.293127]   alloc kstat_irqs on node -1
[    0.293137] pcieport 0000:00:1c.2: irq 27 for MSI/MSI-X
[    0.293148] pcieport 0000:00:1c.2: setting latency timer to 64
[    0.293264] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.293420] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.293586] ACPI: AC Adapter [AC0] (on-line)
[    0.293673] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.295519] ACPI: Lid Switch [LID]
[    0.295572] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.295580] ACPI: Power Button [PWRB]
[    0.295638] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    0.295645] ACPI: Sleep Button [SLPB]
[    0.295692] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.295695] ACPI: Power Button [PWRF]
[    0.296611] ACPI: SSDT 3ffb91b0 00D24 (v01    AMI   CPU1PM 00000001 INTL 02002026)
[    0.297167] Marking TSC unstable due to TSC halts in idle
[    0.297254] processor LNXCPU:00: registered as cooling_device0
[    0.297820] ACPI Warning: Incorrect checksum in table [SSDT] - 21, should be 64 (20090903/tbutils-314)
[    0.297827] ACPI: SSDT 3ffb9ee0 00D24 (v01    AMI   CPU2PM 00000001 INTL 02002026)
[    0.298280] Switching to clocksource hpet
[    0.298528] processor LNXCPU:01: registered as cooling_device1
[    0.304061] thermal LNXTHERM:01: registered as thermal_zone0
[    0.304071] ACPI: Thermal Zone [THRM] (42 C)
[    0.305836] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.307463] brd: module loaded
[    0.308025] loop: module loaded
[    0.308123] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    0.308237] ata_piix 0000:00:1f.2: version 2.13
[    0.308260]   alloc irq_desc for 19 on node -1
[    0.308263]   alloc kstat_irqs on node -1
[    0.308271] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.308277] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    0.308324] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.308423] scsi0 : ata_piix
[    0.308504] scsi1 : ata_piix
[    0.309779] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    0.309783] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    0.310179] Fixed MDIO Bus: probed
[    0.310223] PPP generic driver version 2.4.2
[    0.310269] tun: Universal TUN/TAP device driver, 1.6
[    0.310272] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.310366] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.310389]   alloc irq_desc for 23 on node -1
[    0.310391]   alloc kstat_irqs on node -1
[    0.310396] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.310414] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.310418] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.310460] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.310482] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    0.310496] ehci_hcd 0000:00:1d.7: debug port 1
[    0.314388] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.314406] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfbc00
[    0.322165] isapnp: Scanning for PnP cards...
[    0.371402] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.371608] usb usb1: configuration #1 chosen from 1 choice
[    0.371645] hub 1-0:1.0: USB hub found
[    0.371657] hub 1-0:1.0: 8 ports detected
[    0.371749] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.371774] uhci_hcd: USB Universal Host Controller Interface driver
[    0.371832] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.371843] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.371848] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.371887] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.371921] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ec00
[    0.372048] usb usb2: configuration #1 chosen from 1 choice
[    0.372079] hub 2-0:1.0: USB hub found
[    0.372086] hub 2-0:1.0: 2 ports detected
[    0.372138] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.372145] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.372149] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.372184] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.372224] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880
[    0.372319] usb usb3: configuration #1 chosen from 1 choice
[    0.372351] hub 3-0:1.0: USB hub found
[    0.372358] hub 3-0:1.0: 2 ports detected
[    0.372409] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.372416] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.372420] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.372456] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.372493] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[    0.372604] usb usb4: configuration #1 chosen from 1 choice
[    0.372632] hub 4-0:1.0: USB hub found
[    0.372640] hub 4-0:1.0: 2 ports detected
[    0.372688] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    0.372695] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.372699] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.372741] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.372782] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e480
[    0.372881] usb usb5: configuration #1 chosen from 1 choice
[    0.372910] hub 5-0:1.0: USB hub found
[    0.372917] hub 5-0:1.0: 2 ports detected
[    0.373061] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.375333] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.378972] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.378979] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.379017] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.379042] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.379067] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.379252] mice: PS/2 mouse device common for all mice
[    0.379563] rtc_cmos 00:03: RTC can wake from S4
[    0.379611] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.379648] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.379843] device-mapper: uevent: version 1.0.3
[    0.385345] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.393124] device-mapper: multipath: version 1.1.0 loaded
[    0.393127] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.401141] EISA: Probing bus 0 at eisa.0
[    0.401150] Cannot allocate resource for EISA slot 1
[    0.401180] EISA: Detected 0 cards.
[    0.401487] Freeing initrd [s]memory[/s]: 7773k freed
[    0.405832] cpuidle: using governor ladder
[    0.405939] cpuidle: using governor menu
[    0.406524] TCP cubic registered
[    0.406703] NET: Registered protocol family 10
[    0.407254] lo: Disabled Privacy Extensions
[    0.407641] NET: Registered protocol family 17
[    0.415188] Using IPI No-Shortcut mode
[    0.415305] PM: Resume from disk failed.
[    0.415321] registered taskstats version 1
[    0.415949]   Magic number: 14:291:520
[    0.416062] rtc_cmos 00:03: setting system clock to 2010-06-01 07:32:57 UTC (1275377577)
[    0.416065] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.416067] EDD information not available.
[    0.443629] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    0.496507] ata1.00: ATA-7: ST9100828AS, 3.ALC, max UDMA/133
[    0.496511] ata1.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.512513] ata1.00: configured for UDMA/133
[    0.584405] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T10N, PR03, max UDMA/33
[    0.600314] ata2.00: configured for UDMA/33
[    0.613158] ACPI: Battery Slot [BAT0] (battery present)
[    0.685843] isapnp: No Plug & Play device found
[    0.685983] scsi 0:0:0:0: Direct-Access     ATA      ST9100828AS      3.AL PQ: 0 ANSI: 5
[    0.686119] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[    0.686124] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.686173] sd 0:0:0:0: [sda] Write Protect is off
[    0.686176] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.686202] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.686353]  sda:
[    0.690064] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T10N  PR03 PQ: 0 ANSI: 5
[    0.699695]  sda1 sda2 sda3 sda4
[    0.701873] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    0.701879] Uniform CD-ROM driver Revision: 3.20
[    0.702040] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    0.702125] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    0.714353] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.714390] Freeing unused kernel [s]memory[/s]: 656k freed
[    0.714825] Write protecting the kernel text: 4676k
[    0.714879] Write protecting the kernel read-only data: 1840k
[    0.733659] udev: starting version 151
[    0.848069] usb 1-8: new high speed USB device using ehci_hcd and address 4
[    0.862418] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.862445] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.862884] r8169 0000:02:00.0: setting latency timer to 64
[    0.863439]   alloc irq_desc for 28 on node -1
[    0.863442]   alloc kstat_irqs on node -1
[    0.863462] r8169 0000:02:00.0: irq 28 for MSI/MSI-X
[    0.864581] eth0: RTL8168b/8111b at 0xf804a000, 00:18:f3:f0:e8:b2, XID 18000000 IRQ 28
[    0.886629] ohci1394 0000:06:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.942085] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[feaff800-feafffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    0.981224] usb 1-8: configuration #1 chosen from 1 choice
[    1.220140] usb 2-2: new low speed USB device using uhci_hcd and address 2
[    1.305984] EXT4-fs (sda4): mounted filesystem with ordered data mode
[    1.398082] usb 2-2: configuration #1 chosen from 1 choice
[    1.640094] usb 4-1: new full speed USB device using uhci_hcd and address 2
[    1.882735] usb 4-1: configuration #1 chosen from 1 choice
[    2.216261] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e018000377d059]
[    2.816697] Adding 2039800k swap on /dev/sda3.  Priority:-1 extents:1 across:2039800k
[    2.929492] udev: starting version 151
[    4.102274] asus_laptop: Asus Laptop Support version 0.42
[    4.107563] asus_laptop:   F3JC model detected
[    4.109858] input: Asus Laptop extra buttons as /devices/virtual/input/input6
[    4.109990] Registered led device: asus::`imleçsürer`
[    4.110123] asus_laptop: Brightness ignored, must be controlled by ACPI video driver
[    4.114134] Linux video capture interface: v2.00
[    4.221146] acpi device:17: registered as cooling_device2
[    4.221605] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:13/LNXVIDEO:00/input/input7
[    4.221738] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    4.226840] vga16fb: initializing
[    4.226845] vga16fb: mapped to 0xc00a0000
[    4.226916] fb0: VGA16 VGA frame buffer device
[    4.242936] stkwebcam: Syntek USB2.0 Camera is now controlling video device /dev/video0
[    4.242963] usbcore: registered new interface driver stkwebcam
[    4.308492] stk11xx: Syntek USB2.0 webcam driver startup
[    4.308530] usbcore: registered new interface driver usb_stk11xx_driver
[    4.308533] stk11xx: v2.0.0 : Syntek USB Video Camera
[    4.336384] intel_rng: FWH not detected
[    4.389949] cfg80211: Calling CRDA to update world regulatory domain
[    4.396058] Bluetooth: Core ver 2.15
[    4.396116] NET: Registered protocol family 31
[    4.396118] Bluetooth: HCI device and connection manager initialized
[    4.396121] Bluetooth: HCI socket layer initialized
[    4.409087] Linux agpgart interface v0.103
[    4.443830] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    4.443965] usbcore: registered new interface driver btusb
[    4.651694] lp: driver loaded but no devices found
[    4.652958] usbcore: registered new interface driver hiddev
[    4.666378] input: Logitech Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input8
[    4.666513] generic-usb 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:1d.0-2/input0
[    4.666549] usbcore: registered new interface driver usbhid
[    4.666553] usbhid: v2.6:USB HID core driver
[    4.912828] type=1505 audit(1275366781.995:2):  operation="profile_load" pid=473 name="/sbin/dhclient3"
[    4.913763] type=1505 audit(1275366781.995:3):  operation="profile_load" pid=473 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[    4.914167] type=1505 audit(1275366781.995:4):  operation="profile_load" pid=473 name="/usr/lib/connman/scripts/dhclient-script"
[    5.884312] cfg80211: World regulatory domain updated:
[    5.884316] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    5.884319] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    5.884322] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    5.884325] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    5.884328] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    5.884331] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.046805] nvidia: module license 'NVIDIA' taints kernel.
[    6.046810] Disabling lock debugging due to kernel taint
[    6.655950] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    6.655963] nvidia 0000:01:00.0: setting latency timer to 64
[    6.656169] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.22  Sun Nov  8 20:26:31 PST 2009
[    6.744717] sdhci: Secure Digital Host Controller Interface driver
[    6.744721] sdhci: Copyright(c) Pierre Ossman
[    6.745166] ricoh-mmc: Ricoh MMC Controller disabling driver
[    6.745168] ricoh-mmc: Copyright(c) Philip Langdale
[    6.745201] ricoh-mmc: Ricoh MMC controller found at 0000:06:01.2 [1180:0843] (rev 1)
[    6.745221] ricoh-mmc: Controller is now disabled.
[    6.849680] sdhci-pci 0000:06:01.1: SDHCI controller found [1180:0822] (rev 19)
[    6.849704] sdhci-pci 0000:06:01.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    6.851810] Registered led device: mmc0::
[    6.852897] mmc0: SDHCI controller on PCI [0000:06:01.1] using PIO
[    6.896029] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[    6.896033] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[    6.896145] iwl3945 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    6.896160] iwl3945 0000:03:00.0: setting latency timer to 64
[    6.965707] iwl3945 0000:03:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[    6.965712] iwl3945 0000:03:00.0: Detected Intel Wireless WiFi Link 3945ABG
[    6.965831]   alloc irq_desc for 29 on node -1
[    6.965834]   alloc kstat_irqs on node -1
[    6.965868] iwl3945 0000:03:00.0: irq 29 for MSI/MSI-X
[    7.190941] Synaptics `imleçsürer`, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[    7.232848] input: SynPS/2 Synaptics `imleçsürer` as /devices/platform/i8042/serio4/input/input9
[    7.284121] phy0: Selected rate control algorithm 'iwl-3945-rs'
[    7.315930] Console: switching to colour frame buffer device 80x30
[    8.125713] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    8.125950] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    8.733574] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[   10.762021] type=1505 audit(1275366787.844:5):  operation="profile_load" pid=825 name="/usr/share/gdm/guest-session/Xsession"
[   10.764098] type=1505 audit(1275366787.844:6):  operation="profile_replace" pid=826 name="/sbin/dhclient3"
[   10.764861] type=1505 audit(1275366787.844:7):  operation="profile_replace" pid=826 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   10.765295] type=1505 audit(1275366787.848:8):  operation="profile_replace" pid=826 name="/usr/lib/connman/scripts/dhclient-script"
[   11.068105] type=1505 audit(1275366788.151:9):  operation="profile_load" pid=827 name="/usr/bin/evince"
[   11.078109] type=1505 audit(1275366788.159:10):  operation="profile_load" pid=827 name="/usr/bin/evince-previewer"
[   11.084195] type=1505 audit(1275366788.167:11):  operation="profile_load" pid=827 name="/usr/bin/evince-thumbnailer"
[   11.274576] type=1505 audit(1275366788.355:12):  operation="profile_load" pid=832 name="/usr/lib/cups/backend/cups-pdf"
[   11.275480] type=1505 audit(1275366788.355:13):  operation="profile_load" pid=832 name="/usr/sbin/cupsd"
[   11.431544] type=1505 audit(1275366788.512:14):  operation="profile_load" pid=833 name="/usr/sbin/mysqld-akonadi"
[   11.667950] NET: Registered protocol family 8
[   11.667953] NET: Registered protocol family 20
[   12.587990] r8169: eth0: link down
[   12.588214] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   12.598813] iwl3945 0000:03:00.0: firmware: requesting iwlwifi-3945-2.ucode
[   12.767062] iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
[   12.839261] Registered led device: iwl-phy0::radio
[   12.839344] Registered led device: iwl-phy0::assoc
[   12.839384] Registered led device: iwl-phy0::RX
[   12.839415] Registered led device: iwl-phy0::TX
[   12.853063] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   15.419587] Bluetooth: L2CAP ver 2.14
[   15.419591] Bluetooth: L2CAP socket layer initialized
[   15.510091] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.510095] Bluetooth: BNEP filters: protocol multicast
[   15.553716] Bridge firewalling registered
[   15.663220] Bluetooth: SCO (Voice Link) ver 0.6
[   15.663223] Bluetooth: SCO socket layer initialized
[   15.800828] ppdev: user-space parallel port driver
[   16.266004] Bluetooth: RFCOMM TTY layer initialized
[   16.266010] Bluetooth: RFCOMM socket layer initialized
[   16.266012] Bluetooth: RFCOMM ver 1.11
[   24.270473] wlan0: deauthenticating from 00:1c:a8:91:c0:93 by local choice (reason=3)
[   24.272768] wlan0: direct probe to AP 00:1c:a8:91:c0:93 (try 1)
[   24.275276] wlan0: direct probe responded
[   24.275283] wlan0: authenticate with AP 00:1c:a8:91:c0:93 (try 1)
[   24.278534] wlan0: authenticated
[   24.278565] wlan0: associate with AP 00:1c:a8:91:c0:93 (try 1)
[   24.281545] wlan0: RX AssocResp from 00:1c:a8:91:c0:93 (capab=0x411 status=0 aid=1)
[   24.281548] wlan0: associated
[   24.285137] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   25.456347] padlock: VIA PadLock not detected.
[   34.384029] wlan0: no IPv6 routers present
[  604.812033] CE: hpet increasing min_delta_ns to 15000 nsec
[ 4694.513076] CE: hpet increasing min_delta_ns to 22500 nsec
[16659.146829] CE: hpet increasing min_delta_ns to 33750 nsec
[31038.025094] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[37754.560069] usb 1-1: new high speed USB device using ehci_hcd and address 5
[37754.693102] usb 1-1: configuration #1 chosen from 1 choice
[37755.575326] dib0700: loaded with support for 13 different device-types
[37755.575860] dvb-usb: found a 'Gigabyte U8000-RH' in cold state, will try to load a firmware
[37755.575870] usb 1-1: firmware: requesting dvb-usb-dib0700-1.20.fw
[37755.647541] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[37755.852531] dib0700: firmware started successfully.
[37756.356076] dvb-usb: found a 'Gigabyte U8000-RH' in warm state.
[37756.356168] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[37756.356425] DVB: registering new adapter (Gigabyte U8000-RH)
[37756.600917] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[37756.656149] xc2028 4-0061: creating new instance
[37756.656156] xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner
[37756.656304] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/input/input11
[37756.656402] dvb-usb: schedule remote query interval to 50 msecs.
[37756.656409] dvb-usb: Gigabyte U8000-RH successfully initialized and connected.
[37756.656879] usbcore: registered new interface driver dvb_usb_dib0700
[38844.343292] usb 1-1: firmware: requesting xc3028-v27.fw
[38844.404640] xc2028 4-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[38844.433273] xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
[38850.602183] xc2028 4-0061: Loading firmware for type=D2620 DTV7 (88), id 0000000000000000.
[38850.711688] xc2028 4-0061: Loading SCODE for type=SCODE HAS_IF_5900 (60000000), id 0000000000000000.
[38872.150435] xc2028 4-0061: Loading firmware for type=D2620 DTV78 (108), id 0000000000000000.
[38872.260187] xc2028 4-0061: Loading SCODE for type=DTV7 DTV78 DTV8 DIBCOM52 CHINA SCODE HAS_IF_5400 (65000380), id 0000000000000000.



Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 01 Haziran 2010 - 21:34:07

http://www.linuxtv.org/wiki/index.php/Gigabyte_U8000-RH burada adım adım anlatılmış. Az bir ingilizce ile yapılabilir sanırım.

Kod Seç Genişlet

dmesgçıktısınında;

usb 5-2: new high speed USB device using ehci_hcd and address 2

böyle bir satır olacak tv kartınız için. Sonrasında söylenen komutları takip edebilirsiniz.

en son aşamaya kadar geldim.son komutu verince:
mv: 'dvb-usb-dib0700-1.20.fw' durumlanamadı: No such file or directory
mv: 'xc3028-v27.fw' durumlanamadı: No such file or directory

hatasını aldım.

[eribol]

[37756.656409] dvb-usb: Gigabyte U8000-RH successfully initialized and connected.

dmesg çıktısında Tv kartınız tanınmış ve kullanıma hazır hale getirilmiş denmiş. Alternatif programları deneyip sonuç alamadıysanız sanırım sorun bağlantı noktalarında.

[mustafaceylan]

analog yayınlar için önereceğiniz bir program varmı.ve bu programın ayarlarını anlatırsanız,yani nasıl kanal bulunur filan çok iyi olur.ben kaffein,xawtv,xbmc ve zapping tv leri denedim olmadı.

[eribol]

Maalesef ben bu konuda tecrübeli değilim ama bağlantıların birinde MeTv denilen bir paketten bahsedilmiş.

[Sherlock Holmes]

analog yayınlar için önereceğiniz bir program varmı.

MythTV

ve bu programın ayarlarını anlatırsanız,yani nasıl kanal bulunur filan çok iyi olur.

Tv kartı sahibi olmadığımdan denemeye fırsatım olmadı hali ile.
Muhtemelen/umarım analog ayarlarınızı otomatik algılar.
Çünkü kendim yapmak istediklerimi, ayrıca bir ayar yapmaksızın gerçekleştirmiştim.
Depodan aratırabilirsiniz.

[zeitgeist]

Tvtime uygulamasıyla da deneyebilirsin. Synaptic aracılığıyla kurulabilir. Nanıl kullanılacağı ile ilgili zamanında kısa bir video hazırlamıştım:

http://www.youtube.com/watch?v=qnD4KN61rcQ

Eğer görüntü-ses almayı başaramazsan tvtime uygulamasını konsoldan çalıştır ve hata iletilerini buraya aktar ki konuyla ilgili bilgisi olanlar değerlendirebilsin.

[mustafaceylan]

tv kartımı değil kamerayı görüyor.

Running tvtime 1.0.2.
Reading configuration from /etc/tvtime/tvtime.xml
I/O warning : failed to load external entity "/home/mustafaceylan/.tvtime/tvtime.xml"
I/O error : Permission denied
I/O error : Permission denied
Cannot change owner of /home/mustafaceylan/.tvtime/tvtime.xml: Permission denied.
videoinput: Driver won't tell us its norm: Invalid argument
videoinput: Can't get tuner info: Invalid argument
videoinput: Driver won't tell us its norm: Invalid argument
videoinput: Can't get tuner info: Invalid argument
I/O error : Permission denied
I/O error : Permission denied
videoinput: Can't mute card.  Post a bug report with your
videoinput: driver info to http://tvtime.net/
videoinput: Include this error: 'Invalid argument'

[zeitgeist]

Çıktıdan anladığım kadarıyla usb tv aygıtını tanımamış ve sürücüye ihtiyaç duyuyor ya da aygıtı sağlıklı bir şekilde tanımıyor. Her ne kadar dmesg çıktısında görünse de bana kalırsa elindeki aygıtın linux sürücüsüne ihtiyacın var. Pek umutlu olmasam da şu çıktılara da bakmakta fayda var.

Kod Seç Genişlet

ls -l /dev/video*

Kod Seç Genişlet

lsmod | grep tv

[mustafaceylan]

ls -l /dev/video*  çıktısı
crw-rw----+ 1 root video 81, 0 2010-06-02 04:51 /dev/video0

lsmod | grep tv çıktısı

hiç bir şey yapmıyor komut satırını gösteriyor  kulanıcı adı :~$

[zeitgeist]

Herhangi bir modül yüklenmemiş, var olan tek video aygıtı kameranın, usb çıktısında aygıt gözükmüyor. Tüm bunlar aygıtın sürücüsüne ihtiyacın olduğunu gösteriyor.

[mustafaceylan]

sürücüsü varmı peki.ve nasıl yüklenecek anlatırsanız sevinirim.ben daha önce anlatılmış herşeyi yaptım ama olmadı.

[heartsmagic]

en son aşamaya kadar geldim.son komutu verince:
mv: 'dvb-usb-dib0700-1.20.fw' durumlanamadı: No such file or directory
mv: 'xc3028-v27.fw' durumlanamadı: No such file or directory

hatasını aldım.

Bence bunun üzerine gidilmeli zira firmware atlanmış. Oradaki son komutu .fw dosyalarının olduğu dizinde verdiğine emin misin?

[mustafaceylan]

evet eminim.o sayfada ne deniyorsa harfi harfine yaptım.isterseniz akşam eve gidince tekrar yapayım tek tek ve çıktılarınıda ekleyeyim buraya.şuan işyerindeyim o yüzden yapamıyorum.ama daha önce o işlemleri yaptığım için bilgisayarımda o dosyalar duruyor.temizlemem gerekirmi.gerekirse nasıl temizliyeyim eski işlemlerden kalma dosyaları


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 04 Haziran 2010 - 17:26:30
dmesg çıktısının son satırları bunlar.başını almadım.burda ne diyor.

[67322.164036] usb 1-1: new high speed USB device using ehci_hcd and address 7
[67322.297157] usb 1-1: configuration #1 chosen from 1 choice
[67322.297569] dvb-usb: found a 'Gigabyte U8000-RH' in cold state, will try to load a firmware
[67322.297578] usb 1-1: firmware: requesting dvb-usb-dib0700-1.20.fw
[67322.335673] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[67322.538832] dib0700: firmware started successfully.
[67323.040403] dvb-usb: found a 'Gigabyte U8000-RH' in warm state.
[67323.040491] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[67323.040715] DVB: registering new adapter (Gigabyte U8000-RH)
[67323.288838] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[67323.289132] xc2028 1-0061: creating new instance
[67323.289138] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
[67323.289383] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/input/input12
[67323.289526] dvb-usb: schedule remote query interval to 50 msecs.
[67323.289533] dvb-usb: Gigabyte U8000-RH successfully initialized and connected

[mustafaceylan]

bir yerde başka birşey daha buldum.benim sorunum bu galiba:
The sad thing is that currently only DVB-T digital TV/HDTV is working because there is no driver written for the CX25843-24Z audio/video decoder which is probably used for the analogue TV/FM radio portion of the device.

benim tv kartı karasal dijital ve analog yayın destekliyor.şimdiye kadar yaptığımız herşey karasal digital içindi.ama benim bulunduğum yerde karasal digital yayın henüz yok.zaten türkiyede nerdeyse hiçbiryerde yok henüz.
bana gt-u8000-rh gigabyte usb cihazının analog kısmını çalıştıracak birşeyler lazım arkadaşlar.

[heartsmagic]

Karasal yayın için bir fikrim yok ne yazık ki. Fakat bir önceki sorun için uçbirimden yapmak yerine dosya yöneticisi ile yapabilirsin işlemleri.

Kod Seç Genişlet

sudo nautilus ile açarsın dosya yöneticisini, dosyaları kesip ilgili dizine taşıyabilirsin.