[Çözüldü] HDD uyku moduna geçmiyor

[BuraKaan]

Laptopumda Ubuntu 18.04 tabanlı Elementary OS kullanıyorum. Bir tane hard diskim var ama kullanmama rağmen dönüyor. Haliyle ısınıyor en son 42 dereceye geldi aşağıdaki komutu verip uyku moduna geçirdim.

Kod Seç Genişlet

sudo hdparm -S 1 /dev/sda
Linux arkada işlem yapıyor gibi görünüyor. Bir kaç dakika diski dinledim ama. Disk salt okunur değil. Windows'ta böyle bir sorun yoktu yeni geçtim.


Mesaj tekrarı yüzünden mesajınız birleştirildi. Bu mesajın gönderim tarihi : 31 Ağustos 2020 - 13:33:12
Diskin markası Seagate.
hdparm -I /dev/sda:

Kod Seç Genişlet

/dev/sda:

ATA device, with non-removable media
Model Number:       ST1000LX015-1U7172                     
Serial Number:      WDEX21HF
Firmware Revision:  SDM1   
Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Used: unknown (minor revision code 0x001f)
Supported: 10 9 8 7 6 5
Likely used: 10
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors:    16514064
LBA    user addressable sectors:   268435455
LBA48  user addressable sectors:  1953525168
Logical  Sector size:                   512 bytes
Physical Sector size:                  4096 bytes
Logical Sector-0 offset:                  0 bytes
device size with M = 1024*1024:      953869 MBytes
device size with M = 1000*1000:     1000204 MBytes (1000 GB)
cache/buffer size  = unknown
Form Factor: 2.5 inch
Nominal Media Rotation Rate: 5400
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254
Recommended acoustic management value: 208, current value: 208
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
     Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
Enabled Supported:
   * SMART feature set
    Security Mode feature set
   * Power Management feature set
   * Write cache
   * Look-ahead
   * Host Protected Area feature set
   * WRITE_BUFFER command
   * READ_BUFFER command
   * NOP cmd
   * DOWNLOAD_MICROCODE
   * Advanced Power Management feature set
    Power-Up In Standby feature set
    SET_MAX security extension
   * 48-bit Address feature set
   * Device Configuration Overlay feature set
   * Mandatory FLUSH_CACHE
   * FLUSH_CACHE_EXT
   * SMART error logging
   * SMART self-test
   * General Purpose Logging feature set
   * WRITE_{DMA|MULTIPLE}_FUA_EXT
   * 64-bit World wide name
   * IDLE_IMMEDIATE with UNLOAD
    Write-Read-Verify feature set
   * WRITE_UNCORRECTABLE_EXT command
   * {READ,WRITE}_DMA_EXT_GPL commands
   * Segmented DOWNLOAD_MICROCODE
   * Gen1 signaling speed (1.5Gb/s)
   * Gen2 signaling speed (3.0Gb/s)
   * Gen3 signaling speed (6.0Gb/s)
   * Native Command Queueing (NCQ)
   * Host-initiated interface power management
   * Phy event counters
   * Idle-Unload when NCQ is active
   * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
   * DMA Setup Auto-Activate optimization
   * Device-initiated interface power management
    Asynchronous notification (eg. media change)
   * Software settings preservation
   * SMART Command Transport (SCT) feature set
   * SCT Write Same (AC2)
   * SCT Features Control (AC4)
   * SCT Data Tables (AC5)
    unknown 206[12] (vendor specific)
    unknown 206[13] (vendor specific)
   * DOWNLOAD MICROCODE DMA command
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
166min for SECURITY ERASE UNIT. 166min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000c500ace07355
NAA : 5
IEEE OUI : 000c50
Unique ID : 0ace07355
Checksum: correct


[BuraKaan]

Sorun çözüldü. Çözüm: https://forum.ubuntu-tr.net/index.php?topic=62392.0