[Çözüldü] Pardus yavaş açılıyor!

[acemiyim91]

Merhaba;
Gene ben Pardusu kurdum sistem sapa sağlam kuruldu.Md5sum-verify cd kontrol hepsini yaptım cd veya kurulumda sorun yok.
Boot menüsünden pardusu seçip, açılış ekranı birazcık doluyor ve dahada ilerlemiyor.5-10 dakika sonra sistem açıldı.Girdiğimde de ses kartı hatası verdi.
Aylar önce kurduğumda da böyle olmuştu.Nerede çakışıyor acaba?

[atomkarinca]

Açılışta Ctrl+Alt+F1 yaparsanız verdiği hatayı görebilirsiniz.

[acemiyim91]

ctrl+alt+f1 tepki vermedi ancak ctrl+altf2 siyah ekrana geçti ve hiç bir hata vermiyor.Fark ettim çok yavaş açılıyor nerede takılıyor?Bunla ilgili bir log yeri yok mudur?

ethernet kartımı nasıl gösterebilirim?

Kod Seç Genişlet


Parola:
irony-pardus ~ # lspci
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. PT890 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139
C+ (rev 10)
00:08.0 Modem: Smart Link Ltd. Device 2800 (rev 02)
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (r                                            ev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/                                            C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller                                             (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller                                             (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller                                             (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller                                             (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T89                                            0 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 A                                            C97 Audio Controller (rev 60)
01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO]                                             (rev 01)
01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Second                                            ary) (rev 01)
irony-pardus ~ # echo 8139too >> /etc/modules.autoload.d/kernel-2.6
irony-pardus ~ # echo 8139too >> /etc/modules.autoload.d/kernel-2.6
irony-pardus ~ # echo 8139too >> /etc/modules.autoload.d/kernel-2.6
irony-pardus ~ # su -
irony-pardus ~ # echo 8139too >> /etc/modules.autoload.d/kernel-2.6
irony-pardus ~ # sudo /sbin/modprobe 8139too
denedim ama cevab yok

[atomkarinca]

Eğer komut ekranı görebiliyorsanız

Kod Seç Genişlet

dmesg

komutuyla en son ne olup bittiğini görebilirsiniz.

[acemiyim91]

ctrl+alt+f2 de şunları gördüm;
İlk başlarda camera found gibi normal açılıyor yanı azıcık dolduğu yere kadar sorun yok ve takılıyor o ara demek ki birşeyleri kontrol ediyor 5-10 dakika sonra devam ediyor;

Kod Seç Genişlet


*/dev/pts dizini bağlanıyor
kök dosya sistemi salt okunur halde yeniden bağlanıyor.
kök dosya sistemi denetim atlandı (fstab pass değeri=0)
kök dosya sistemi okunur/yazılır halde yeniden bağlanıyor.
sistem adı acemiyim91-pardus olarak ayarlanıyor.
Calculating module dependencies for 2.6.25.16-108

bundan sonrada tepki vermedi bende reset attım pc ye slackware 12.2 kurdum pardusda duruyor yardımlarınızı bekliyorum.

[acemiyim91]

O yazılardan sonra
Daha önce başarısız olan udev tekrar başlıyor
gibisinden yazıyor ve sistem açılıyor.



dmesg

Kod Seç Genişlet



iRoNY-Pardus iRoNY # dmesg
Linux version 2.6.25.16-108 (pardus@buildfarm) (gcc version 4.3.1 (Pardus Linux) ) #1 SMP Tue Aug 26 15:29:43 EEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS)
BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00f5150] 000f5150
Entering add_active_range(0, 0, 130800) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130800
  HighMem    130800 ->   130800
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   130800
On node 0 totalpages: 130800
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 989 pages used for memmap
  Normal zone: 125715 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F7240, 0014 (r0 P4M80P)
ACPI: RSDT 1FEF3040, 0034 (r1 P4M80P AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 1FEF30C0, 0074 (r1 P4M80P AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 1FEF3180, 54E1 (r1 P4M80P AWRDACPI     1000 MSFT  100000E)
ACPI: FACS 1FEF0000, 0040
ACPI: APIC 1FEF86C0, 0068 (r1 P4M80P AWRDACPI 42302E31 AWRD        0)
ACPI: SSDT 1FEF8770, 015C (r1  PmRef  Cpu0Ist     3000 INTL 20041203)
ACPI: SSDT 1FEF8C00, 014E (r1  PmRef    CpuPm     3000 INTL 20041203)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1ff00000:ded00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129779
Kernel command line: root=LABEL=PARDUS_ROOT vga=791 splash=silent quiet resume=/dev/sda2
bootsplash: silent mode.
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2994.375 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 509528k/523200k available (1901k kernel code, 13076k reserved, 1020k data, 264k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe14000 - 0xfffff000   (1964 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdfef0000   ( 510 MB)
      .init : 0xc03e2000 - 0xc0424000   ( 264 kB)
      .data : 0xc02db4bc - 0xc03da67c   (1020 kB)
      .text : 0xc0100000 - 0xc02db4bc   (1901 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=128, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 5993.47 BogoMIPS (lpj=2996737)
Security Framework initialized
AppArmor: AppArmor initialized <NULL>
AppArmor: Registered secondary security module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Booting processor 1/1 ip 4000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5971.33 BogoMIPS (lpj=2985665)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Total of 2 processors activated (11964.80 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000003
  groups: 00000001 00000002
  domain 1: span 00000003
   groups: 00000003
CPU1 attaching sched-domain:
domain 0: span 00000003
  groups: 00000002 00000001
  domain 1: span 00000003
   groups: 00000003
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3c0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
AppArmor: AppArmor Filesystem Enabled
ACPI: RTC can wake from S4
system 00:00: iomem range 0xd0000-0xd3fff has been reserved
system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x1fef0000-0x1fefffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x1feeffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:00: iomem range 0xfff80000-0xfffeffff could not be reserved
system 00:02: ioport range 0x400-0x47f has been reserved
system 00:02: ioport range 0x500-0x50f has been reserved
system 00:03: ioport range 0xb78-0xb7b has been reserved
system 00:03: ioport range 0xf78-0xf7b has been reserved
system 00:03: ioport range 0xa78-0xa7b has been reserved
system 00:03: ioport range 0xe78-0xe7b has been reserved
system 00:03: ioport range 0xbbc-0xbbf has been reserved
system 00:03: ioport range 0xfbc-0xfbf has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
system 00:03: ioport range 0x290-0x297 has been reserved
system 00:03: ioport range 0x880-0x88f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: b000-bfff
  MEM window: 0xfde00000-0xfdefffff
  PREFETCH window: 0x00000000e0000000-0x00000000efffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 4744k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1229958223.519:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
pci 0000:00:10.4: EHCI: BIOS handoff failed (BIOS bug?) 01010001
pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xe8000000, mapped to 0xe0880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:5799
vesafb: pmi: set display start = c00c582d, set palette = c00c5879
vesafb: pmi: ports = bc10 bc16 bc54 bc38 bc3c bc5c bc00 bc04 bcb0 bcb2 bcb4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 170855 bytes
bootsplash: ...found (1024x768, 25378 bytes, v3).
Console: switching to colour frame buffer device 128x45
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:08.0 disabled
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
NET: Registered protocol family 1
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
Write protecting the kernel read-only data: 832k
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdffe000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25.16-108 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI interrupt for device 0000:00:0f.0 disabled
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI interrupt for device 0000:00:0f.1 disabled
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25.16-108 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 1
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25.16-108 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25.16-108 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 3
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.25.16-108 uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
sata_via 0000:00:0f.0: version 2.3
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 11
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0xf800 ctl 0xf400 bmdma 0xe800 irq 20
ata2: SATA max UDMA/133 cmd 0xf000 ctl 0xec00 bmdma 0xe808 irq 20
hub 1-0:1.0: unable to enumerate USB device on port 4
ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
usb 2-1: new full speed USB device using uhci_hcd and address 2
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
pata_via 0000:00:0f.1: version 0.3.3
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
scsi2 : pata_via
scsi3 : pata_via
ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=0ac8, idProduct=303b
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: PC Camera
usb 2-1: Manufacturer: Vimicro Corp.
ata3.00: HPA detected: current 234439535, native 234441648
ata3.00: ATA-6: WDC WD1200BB-22GUC0, 08.02D08, max UDMA/100
ata3.00: 234439535 sectors, multi 16: LBA48
ata3.00: configured for UDMA/100
usb 3-1: new low speed USB device using uhci_hcd and address 2
ata4.00: ATAPI: TSSTcorp CDW/DVD SH-M522C, TS05, max UDMA/33
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=045e, idProduct=0083
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Basic Optical Mouse
usb 3-1: Manufacturer: Microsoft
ata4.00: configured for UDMA/33
scsi 2:0:0:0: Direct-Access     ATA      WDC WD1200BB-22G 08.0 PQ: 0 ANSI: 5
scsi 3:0:0:0: CD-ROM            TSSTcorp CDW/DVD SH-M522C TS05 PQ: 0 ANSI: 5
usb 3-2: new low speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 3-2: New USB device found, idVendor=04f3, idProduct=0103
usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver hiddev
input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.0/input/input1
input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:10.1-1
input: HID 04f3:0103 as /devices/pci0000:00/0000:00:10.1/usb3/3-2/3-2:1.0/input/input2
input,hidraw1: USB HID v1.10 Keyboard [HID 04f3:0103] on usb-0000:00:10.1-2
input: HID 04f3:0103 as /devices/pci0000:00/0000:00:10.1/usb3/3-2/3-2:1.1/input/input3
input,hidraw2: USB HID v1.10 Device [HID 04f3:0103] on usb-0000:00:10.1-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 8x/52x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 234439535 512-byte hardware sectors (120033 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 234439535 512-byte hardware sectors (120033 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 2:0:0:0: [sda] Attached SCSI disk
PM: Starting manual resume from disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 126 started
sd 2:0:0:0: Attached scsi generic sg0 type 0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
sr 3:0:0:0: Attached scsi generic sg1 type 5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.103
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
BUG: unable to handle kernel paging request at 75626564
IP: [<c01dc300>] strnlen+0x9/0x19
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in: slamr(P+) agpgart shpchp mii v4l1_compat pci_hotplug sg ext3 jbd mbcache sd_mod sr_mod cdrom usbhid hid ff_memless pata_via sata_via uhci_hcd pata_acpi ata_generic libata scsi_mod dock ehci_hcd usbcore

Pid: 380, comm: modprobe Tainted: P         (2.6.25.16-108 #1)
EIP: 0060:[<c01dc300>] EFLAGS: 00210097 CPU: 1
EIP is at strnlen+0x9/0x19
EAX: 75626564 EBX: c043a86e ECX: 75626564 EDX: fffffffe
ESI: df7c5da8 EDI: 75626564 EBP: df7c5cdc ESP: df7c5cdc
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 380, ti=df7c4000 task=df5d4000 task.ti=df7c4000)
Stack: df7c5d10 c01db960 e12029db 00000400 c043a854 00000010 c043ac54 00000000
       ffffffff ffffffff 00000400 c043a854 df4b5800 df7c5d20 c01dbb6f df7c5da0
       00000000 df7c5d84 c0123787 df7c5da0 00000006 df480f84 00200292 00000001
Call Trace:
[<c01db960>] ? vsnprintf+0x287/0x420
[<c01dbb6f>] ? vscnprintf+0xe/0x1c
[<c0123787>] ? vprintk+0xfb/0x2d9
[<c0185a17>] ? find_inode+0x1f/0x5b
[<c01afcd4>] ? sysfs_ilookup_test+0x0/0x11
[<c0185897>] ? iput+0x3c/0x66
[<c02d5c50>] ? printk+0xf/0x17
[<e0840027>] ? amrmo_pci_probe+0x27/0x32d [slamr]
[<c01e56e1>] ? pci_match_device+0x8d/0x93
[<c01e579b>] ? pci_device_probe+0x39/0x59
[<c02414df>] ? driver_probe_device+0xa0/0x136
[<c02415d0>] ? __driver_attach+0x5b/0x91
[<c0240ebc>] ? bus_for_each_dev+0x3b/0x63
[<c0241384>] ? driver_attach+0x14/0x16
[<c0241575>] ? __driver_attach+0x0/0x91
[<c02408ba>] ? bus_add_driver+0x9d/0x1ba
[<c0241744>] ? driver_register+0x47/0xa7
[<c01e5950>] ? __pci_register_driver+0x35/0x61
[<e08403ca>] ? amrmo_init+0x9d/0xdf [slamr]
[<c0141f16>] ? sys_init_module+0x18ab/0x19c8
[<c01e23af>] ? pci_bus_read_config_byte+0x0/0x57
[<c01bfff6>] ? security_file_permission+0xf/0x11
[<c0175aa9>] ? sys_read+0x3b/0x60
[<c01049b4>] ? sysenter_past_esp+0x6d/0xa5
[<c02d0000>] ? pcibios_setup+0x12c/0x281
=======================
Code: 05 bf 01 00 00 00 4f 89 f8 5f 5d c3 55 85 c9 89 e5 57 89 c7 89 d0 74 05 f2 ae 75 01 4f 89 f8 5f 5d c3 55 89 c1 89 e5 89 c8 eb 06 <80> 38 00 74 07 40 4a 83 fa ff 75 f4 29 c8 5d c3 55 89 e5 57 56
EIP: [<c01dc300>] strnlen+0x9/0x19 SS:ESP 0068:df7c5cdc
---[ end trace 7d843f923a78bd78 ]---
Linux video capture interface: v2.00
8139too Fast Ethernet driver 0.9.28
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: SSDT 1FEF8B70, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20041203)
ACPI: ACPI0007:01 is registered as cooling_device1
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
ACPI: Sleep Button (CM) [SLPB]
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10
usb 2-1: ZC0301[P] Image Processor and Control Chip detected (vid/pid 0x0AC8:0x303B)
usb 2-1: PB-0330 image sensor detected
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [THRM] (39 C)
usb 2-1: Initialization succeeded
usb 2-1: V4L2 device registered as /dev/video0
usbcore: registered new interface driver zc0301
usbcore: registered new interface driver gspca
/var/pisi/gspca-0.0_20071224-14/work/gspcav1-20071224/gspca_core.c: gspca driver 01.00.20 registered
ACPI: PNP0C0B:00 is registered as cooling_device2
ACPI: Fan [FAN] (on)
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
EXT3 FS on sda3, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
Adding 1550264k swap on /dev/sda2.  Priority:-1 extents:1 across:1550264k
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.29.0 20080528 on minor 0




lsmod

Kod Seç Genişlet



iRoNY-Pardus iRoNY # lsmod
Module                  Size  Used by
radeon                129028  0
drm                   168804  1 radeon
ipv6                  245992  16
firmware_class         13056  0
acpi_cpufreq           13068  0
cpufreq_powersave       5760  0
cpufreq_userspace       8196  0
fuse                   48924  2
snd_via82xx            30769  1
gameport               18060  1 snd_via82xx
snd_ac97_codec         97568  1 snd_via82xx
ac97_bus                5888  1 snd_ac97_codec
snd_seq_dummy           7812  0
snd_seq_oss            34332  0
snd_seq_midi_event     11008  1 snd_seq_oss
snd_seq                51496  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
ppdev                  12702  1
snd_pcm_oss            41376  0
snd_mixer_oss          19200  1 snd_pcm_oss
snd_pcm                73476  3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
parport_pc             41108  1
lp                     15390  1
snd_timer              25608  2 snd_seq,snd_pcm
snd_page_alloc         13960  2 snd_via82xx,snd_pcm
rtc_cmos               14112  0
parport                37972  3 ppdev,parport_pc,lp
snd_mpu401_uart        12160  1 snd_via82xx
fan                     9604  0
rtc_core               22940  1 rtc_cmos
snd_rawmidi            26912  1 snd_mpu401_uart
gspca                 652900  0
snd_seq_device         11788  4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
rtc_lib                 6912  1 rtc_core
thermal                22940  0
serio_raw              10628  0
joydev                 15424  0
snd                    57528  12 snd_via82xx,snd_ac97_codec,snd_seq_dummy,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
i2c_viapro             12205  1
soundcore              11336  1 snd
zc0301                 52868  0
compat_ioctl32          5376  1 zc0301
i2c_core               26516  2 drm,i2c_viapro
via_agp                13863  1
button                 12176  0
processor              43948  2 acpi_cpufreq,thermal
8139too                28707  1
videodev               33152  2 gspca,zc0301
slamr                 436628  1
agpgart                36020  2 drm,via_agp
shpchp                 33940  0
mii                     9344  1 8139too
v4l1_compat            16260  1 videodev
pci_hotplug            30884  1 shpchp
sg                     37044  0
ext3                  128008  2
jbd                    47636  1 ext3
mbcache                12420  1 ext3
sd_mod                 29976  5
sr_mod                 19624  0
cdrom                  35740  1 sr_mod
usbhid                 44900  0
hid                    39500  1 usbhid
ff_memless              9352  1 usbhid
pata_via               14980  4
sata_via               14980  0
uhci_hcd               26640  0
pata_acpi              11136  0
ata_generic            12036  0
libata                150240  4 pata_via,sata_via,pata_acpi,ata_generic
scsi_mod              145268  4 sg,sd_mod,sr_mod,libata
dock                   14352  1 libata
ehci_hcd               37132  0
usbcore               136396  6 gspca,zc0301,usbhid,uhci_hcd,ehci_hcd


[acemiyim91]

Çözüldü.

Kod Seç Genişlet


echo "blacklist slamr" >> /etc/modprobe.d/blacklist-compat
İyi ki benden önce profesyonel kişilerde bunu yaşamış, hata.
http://hata.pardus.org.tr/ adersen çözüm verdiler sağolsunlar.Etherneti mi de tanıdı bir daha format attım:)